Page 614 of 692
6148-2. Steps to take in an emergency
IS300h_EE(OM53D89E)
Take out the repair kit from the tool box.
Remove the valve cap from the valve
of the punctured tire.
Remove the protective film from the
bottle and extend the hose. Remove
the air release cap from the hose.
Attach the sticker enclosed with the bot-
tle on the specified locations. (See step
9.)
You will use the air release cap again.
Therefore keep it in a safe place.
Connect the hose to the valve.
Screw the end of the hose clockwise as
far as possible.
Emergency repair method
1
2
3
4
Page 615 of 692
6158-2. Steps to take in an emergency
8
When trouble arises
IS300h_EE(OM53D89E)
Make sure that the compressor
switch is off.
Remove the power plug from the
compressor.
Connect the power plug to the
power outlet socket. ( P. 492)
5
6
7
Page 616 of 692
6168-2. Steps to take in an emergency
IS300h_EE(OM53D89E)
Remove the sticker.
Attach the 2 stickers as shown.
Remove any dirt and moisture from the wheel before attaching the label. If it is
impossible to attach the label, make sure
to tell any authorized Lexus retailer or Lexus authorized repairer, or any reli-
able repairer when you have them
repair and replace the tire that sealant is injected.
8
9
Page 617 of 692
6178-2. Steps to take in an emergency
8
When trouble arises
IS300h_EE(OM53D89E)
Connect the bottle to the compres-
sor.
As shown in the illustration, insert the
bottle vertically in to the compressor to connect making sure that the claw on
the bottle's neck is hooked onto the cut-
out of the compressor case.
Check the specified tire inflation pressure.
Tire inflation pressure is spec ified on the label as shown. (P. 652)
10
11
Left-hand drive vehiclesRight-hand drive vehicles
Page 618 of 692

6188-2. Steps to take in an emergency
IS300h_EE(OM53D89E)
Start the hybrid system.
To inject the sealant and inflate the
tire, turn the compressor switch on.
Inflate the tire until the specified air
pressure is reached.
The sealant will be injected and
the pressure will surge and then
gradually decrease.
The air pressure gauge will dis-
play the actual tire inflation pres-
sure about 1 minute (5 minutes at
low temperature) after the switch
is turned on.
Inflate the tire until the specified
air pressure.
• Turn the compressor switch off
and then check the tire infla-
tion pressure. Being careful
not to over inflate, check and
repeat the inflation procedure
until the specified tire inflation
pressure is reached.
• If the tire inflation pressure is still lower than the specified point after
inflation for 35 minutes with the swit ch on, the tire is too damaged to be
repaired. Turn the compressor swit ch off and contact any authorized
Lexus retailer or Lexus authorized repairer, or any reliable repairer.
• If the tire inflation pressure exceed s the specified air pressure, let out
some air to adjust the tire inflation pressure. ( P. 622, 652)
12
13
14
1
2
3
Page 619 of 692
6198-2. Steps to take in an emergency
8
When trouble arises
IS300h_EE(OM53D89E)
With the compressor switch off, disconnect the hose from the valve on the tire
and then pull out the power plug from the power outlet socket.
Some sealant may leak when the hose is removed.
Install the valve cap onto the valve of the emergency repaired tire.
Attach the air release cap to the end
of the hose.
If the air release cap is not attached, the
sealant may leak and the vehicle may
get dirty.
Temporarily store the bottle in the luggage compartment while it is connected
to the compressor.
To spread the liquid sealant evenly within the tire, immediately drive safely for
about 5 km (3 miles) below 80 km/h (50 mph).
After driving for about 5 km (3
miles), stop your vehicle in a safe
place on a hard, flat surface and
remove the air release cap from the
hose before reconnecting the repair
kit.
15
16
17
18
19
20
Page 620 of 692

6208-2. Steps to take in an emergency
IS300h_EE(OM53D89E)
Turn the compressor switch on and
wait for an approximately 5 seconds,
and then turn it off. Check the tire
inflation pressure.
If the tire inflation pressure is
under 130 kPa (1.3 kgf/cm2 or
bar, 19 psi): The puncture cannot
be repaired. Contact any autho-
rized Lexus retailer or Lexus
authorized repairer, or any reli-
able repairer.
If the tire inflation pressu re is 130 kPa (1.3 kgf/cm2 or bar, 19 psi) or higher,
but less than the specified air pressure: Proceed to .
If the tire inflation pressure is the specified air pressure ( P. 652): Pro-
ceed to .
Turn the compressor switch on to inflat e the tire until the specified air pressure
is reached. Drive for about 5 km (3 miles) and then perform .
Attach the air release cap to the end
of the hose.
If the air release cap is not attached, the
sealant may leak and the vehicle may get dirty.
Store the bottle in the luggage compartm ent while it is connected to the com-
pressor.
Taking precautions to avoid sudden br aking, sudden acceleration and sharp
turns, drive carefully at under 80 km/h (50 mph) to the nearest authorized
Lexus retailer or Lexus authorized repa irer, or any reliable repairer for tire
repair or replacement.
21
1
2
22
3
23
22
20
23
24
25
Page 621 of 692

6218-2. Steps to take in an emergency
8
When trouble arises
IS300h_EE(OM53D89E)
■Emergency tire puncture repair kit
●The sealant has a limited lifespan. The expiry date is marked on the bottle. The sealant
should be replaced before the expiry date. Contact any authorized Lexus retailer or Lexus authorized repairer, or any reliable repairer for replacement.
●The sealant stored in the emergency tire puncture repair kit can be used only once to
temporarily repair a single tire. If the sealant in the bottle and other parts of the kit have been used and need to be purchased, cont act any authorized Lexus retailer or Lexus
authorized repairer, or any reliable repairer.
●The sealant can be used when the outside temperature is from -30C (-22F) to 60C (140 F).
●The kit is exclusively designed for size and type of tires originally installed on your vehi-
cle. Do not use it for tires that a different size than the original ones, or for any other purposes.
●If the sealant gets on yo ur clothes, it may stain.
●If the sealant adheres to a wheel or the surface of the vehicle body, the stain may not be removable if it is not cleaned at once. I mmediately wipe away the sealant with a wet
cloth.
●During operation of the kit, a loud operation noise is produced. This does not indicate a malfunction.
■After a tire is repaired with the emergency tire puncture repair kit
●The tire pressure warning valve and transmitter should be replaced.
●Even if the tire inflation pressure is at the recommended level, the tire pressure warning
light may come on/flash.
■Note for checking the emergency tire puncture repair kit
Check the sealant expiry date occasionally.
The expiry date is shown on the bottle. Do not use sealant whose expiry date has already
passed. Otherwise, repairs conducted using the emergency tire puncture repair kit may not be performed properly.