6228-2. Steps to take in an emergency
IS300h_EE(OM53D89E)
■If the tire is inflated to more than the recommended level
Disconnect the hose from the valve.
Disconnect the hose from the valve, remove the air release cap from the hose and then
reconnect the hose.
Turn the compressor switch on and wait for se veral seconds, then turn it off. Check that the air pressure indicator sh ows the recommended level. (P. 652)
If the air pressure is lower than the reco mmended level, turn the compressor switch on
again and repeat the inflation procedure un til the recommended pressure is reached.
Install the air release cap to the end of the
hose and push the protrusion on the air release cap into the valve to let some air out.
WARNING
■Caution while driving
Observe the following precautions. Failure to do so may cause an accident.
●The emergency tire puncture re pair kit is made exclusively for your vehicle. Do not
use it on other vehicles.
●Do not use the emergency tire puncture repa ir kit for tires that are a different size
than the specified ones or for any other pu rpose. Doing so may cause the tires to not
be repaired properly.
■Precautions for use of the sealant
●Ingesting the sealant is haza rdous to your health. If you ingest sealant, consume as
much water as possible, then immediately consult a doctor.
●If sealant gets in eyes or adheres to skin, immediately wash it off with water. If discom-
fort persists, consult a doctor.
1
2
3
4
6238-2. Steps to take in an emergency
8
When trouble arises
IS300h_EE(OM53D89E)
WARNING
■When fixing the flat tire
●Stop your vehicle in a safe and flat area.
●Do not touch the wheels or the area around the brakes immediately after the vehicle
has been driven. After the vehicle has been driven, the wheels and the area around the brakes may be
extremely hot. Touching these areas with hands, feet or other body parts may result in
burns.
●Connect the valve and hose securely wi th the tire installed on the vehicle.
●If the hose is not properly connected to the valve, air leakage may occur or sealant
may be sprayed out.
●If the hose comes off the valve while inflating the tire, there is a risk that the hose will
move abruptly due to air pressure.
●After inflation of the tire ha s completed, the sealant may splatter when the hose is dis- connected or some air is let out of the tire.
●Follow the operation procedure to repair the tire. If the procedure is not followed, the
sealant may spray out.
●Keep back from the tire while it is being re paired, as there is a chance of it bursting
while the repair operation is being performed. If you notice any cracks or deforma-
tion of the tire, turn off the compressor sw itch and stop the repair operation immedi- ately.
●The kit may overheat if operated for a long period of time. Do not operate the com-
pressor continuously for more than 10 minutes.
●Parts of the kit become hot during operatio n. Be careful handling the kit during and
after operation.
●Do not attach the vehicle speed warning stic ker to an area other than the one indi- cated. If the sticker is attached to an area where an SRS airbag is located, such as the
pad of the steering wheel, it may prevent the SRS air bag from operating properly.
■Driving to spread the liquid sealant evenly
●Drive the vehicle carefully at a low speed. Be especially careful when turning and cor-
nering.
●If the vehicle does not drive straight or you feel a pull through the steering wheel, stop the vehicle and check the following:
• Tire condition. The tire may have separated from the wheel.
• Tire inflation pressure. If tire infl ation pressure is 130 kPa (1.3 kgf/cm2 or bar, 19 psi) or below, this may indi cate severe tire damage.
6248-2. Steps to take in an emergency
IS300h_EE(OM53D89E)
NOTICE
■When performing an emergency repair
●Perform the emergency repair without removing the nail or screw that has punctured
the tread of the tire. If the object that has punctured the tire is removed, repair by the
emergency tire puncture repair kit may not be possible.
●The kit is not waterproof. Make sure that the kit is not exposed to water, such as when
it is being used in the rain.
●Do not put the kit directly onto dusty ground such as sand at the side of the road. If the kit vacuums up dust etc., a malfunction may occur.
●Use the kit with the top facing upward. The kit cannot work properly if it is laid on its
side.
■Handling the emergency tire puncture repair kit
●The compressor power source should be 12 V DC suitable for vehicle use. Do not
connect the compressor to any other source.
●If gasoline splatters on the ki t, the kit may deteriorate. Take care not to allow gasoline
to contact it.
●Store the kit in its assigned place out of reach of children.
●Do not disassemble or modify the kit. Do not subject parts such as the air pressure
indicator to impacts. This may cause a malfunction.
■To avoid damage to the tire pressure warning valves and transmitters
When a tire is repaired with liquid sealants , the tire pressure warning valve and trans-
mitter may not operate properly. If a liqui d sealant is used, contact any authorized
Lexus retailer or Lexus authorized repairer, or any reliable repairer as soon as possible. After use of liquid sealant, make sure to replace the tire pressure warning valve and
transmitter when repairing or replacing the tire. (P. 526)
6258-2. Steps to take in an emergency
8
When trouble arises
IS300h_EE(OM53D89E)
■Run-flat tires (A “RFT” or “DSST” mark is molded on the sidewall)
Take your vehicle to the nearest
Lexus dealer or authorized tire
dealer as soon as possible if any tire
goes flat.
The vehicle can be driven for a maxi- mum of 300 km (186 miles) at a
speed below 60 km/h (37 mph)
after the tire pressure warning light comes on. ( P. 578)
■In some conditions (such as at high temperatures)
You cannot continue driving for up to 300 km (186 miles).
■For the detailed informat ion on run-flat tires
See the tire warranty booklet.
If you have a flat tire (vehicles with run-flat tires)
Your vehicle is not equipped with a sp are tire, but instead you can continue
driving the vehicle with run-flat tires even if any tire goes flat.In this case, slow
down and drive with extra caution.
NOTICE
■When replacing the tires
When removing or fitting the wheels, tires or the tire pressure warning valve and trans-
mitter, contact any authorized Lexus retailer or Lexus authorized repairer, or any reli- able repairer as the tire pressure warning valve and transmitter may be damaged if not
handled correctly.
■When driving over bumps
If a vehicle has a flat tire, the vehicle height will be lower than usual. Ensure that nothing
strikes the bottom of the vehicle.
■To avoid damage to the tire pressure warning valves and transmitters
When a tire is repaired with liquid sealants , the tire pressure warning valve and trans-
mitter may not operate properly. If a liqui d sealant is used, contact any authorized
Lexus retailer or Lexus authoriz ed repairer, or any reliable repairer or other qualified service shop as soon as possible. Make sure to replace the tire pressure warning valve
and transmitter when replacing the tire. ( P. 526)
6268-2. Steps to take in an emergency
IS300h_EE(OM53D89E)
One of the following may be the cause of the problem:
●The electronic key may not be functioning properly. (P. 629)
●There may not be sufficient fuel in the vehicle’s tank.
Refuel the vehicle.
●There may be a malfunction in the immobilizer system. ( P. 86)
●There may be a malfunction in the steering lock system.
●The hybrid system may be malfunctioning due to an electrical problem such
as electronic key battery depletion or a blown fuse. However, depending on
the type of malfunction, an interim meas ure is available to start the hybrid sys-
tem. ( P. 627)
One of the following may be the cause of the problem:
●The 12-volt battery may be discharged. ( P. 631)
●The 12-volt battery terminal connections may be loose or corroded.
( P. 522)
If the hybrid system will not start
Reasons for the hybrid system not starting vary depending on the situation.
Check the following and perfor m the appropriate procedure:
The hybrid system will not start even though the correct starting proce-
dure is being followed. ( P. 219)
The interior lights and headlights are dim, or the horn does not sound or
sounds at a low volume.
6278-2. Steps to take in an emergency
8
When trouble arises
IS300h_EE(OM53D89E)
One of the following may be the cause of the problem:
●The 12-volt battery may be discharged. (P. 631)
●One or both of the 12-volt battery terminals may be disconnected.
( P. 522)
Contact any authorized Lexus retailer or Lexus authorized repairer, or any reliable
repairer if the problem canno t be repaired, or if repair procedures are unknown.
When the hybrid system does not start, the following steps can be used as an
interim measure to start the hybrid system if the power switch is functioning nor-
mally.
Do not use this starting procedur e except in cases of emergency.
Set the parking brake.
Shift the shift lever to P.
Turn the power switch to ACCESSORY mode.
Press and hold the power switch for ab out 15 seconds while depressing the
brake pedal firmly.
Even if the hybrid system can be starte d using the above steps, the system may
be malfunctioning. Have the vehicle insp ected by any authorized Lexus retailer
or Lexus authorized repairer , or any reliable repairer.
The interior lights and headlights do not turn on, or the horn does not
sound.
Emergency start function
1
2
3
4
6288-2. Steps to take in an emergency
IS300h_EE(OM53D89E)
■Doors
Use the mechanical key ( P. 139)
in order to perform the following
operations:
Locks all the doors
Closes the windows and moon
roof (turn and hold)*
Unlocks all the doors
Opens the windows and moon roof (turn and hold)*
*: This setting must be customized at any authorized Lexus retailer or Lexus autho-
rized repairer, or an y reliable repairer.
■Trunk
Turn the mechanical key clockwise
to open.
If the electronic key does not operate properly
If communication between the electronic key and vehicle is interrupted ( P.
159) or the electronic key cannot be us ed because the battery is depleted, the
smart entry & start system and wireless remote control cannot be used. In
such cases, the doors and trunk can be opened and the hybrid system can be
started by following the procedure below.
Locking and unlocking the doors, unlocking the trunk and key linked
functions
1
2
3
4
6298-2. Steps to take in an emergency
8
When trouble arises
IS300h_EE(OM53D89E)
Ensure that the shift lever is in P and depress the brake pedal.
Touch the Lexus emblem side of the
electronic key to the power switch.
When the electronic key is detected, a buzzer sounds and th e power switch will
turn to ON mode.
When the smart entry & start system is deactivated in custom ization setting, the
power switch will turn to ACCESSORY
mode.
Firmly depress the brake pedal and check that is shown on the multi-
information display.
Press the power switch.
In the event that the hybrid system still cannot be started, contact any authorized
Lexus retailer or Lexus authorized repairer, or any reliable repairer.
Starting the hybrid system
1
2
3
4