2017 KIA BORREGO Owners Manual

653
Driving your vehicle
✽✽NOTICE
 During normal cruise control oper- ation, when the SET switch is acti-
vated or reactivated after applying
the brakes, the cruise control will
energize after approximately 3 sec-
onds. This delay is normal.
 To activate cruise control, depress the brake pedal at least once after
turning the ignition switch to the ON
position or starting the engine. This
is to check if the brake switch which
is important part to cancel cruise
control is in normal condition.Cruise control switch
CANCEL/O : Cancels cruise control operation.
CRUISE / : Turns cruise control system on or off.
RES+ : Resumes or increases cruise
control speed.
SET- : Sets or decreases cruise con- trol speed. To set cruise control speed:
1. Press the CRUISE / button on
the steering wheel, to turn the sys-
tem on. The cruise indicator light
will illuminate.
2. Accelerate to the desired speed, which must be more than approxi- mately 40 km/h (25 mph).
OHM056055L
OHM056054L
■Type A
■Type BOHM056053L
■Type A
■Type B

Driving your vehicle
54
6
3. Move the lever down (to SET-),
and release it at the desired
speed. The cruise set indicator
light will illuminate. Release the
accelerator pedal at the same
time. The desired speed will auto-matically be maintained.
On a steep grade, the vehicle may
slow down or speed up slightly whilegoing downhill.To increase cruise control set speed:
Follow either of these procedures:
Move the lever up (to RES+) and hold it. Your vehicle will accelerate.
Release the lever at the speed you
want.
OHM056058L
OHM056059L
■Type A
■Type B
OHM056057L
OHM056056L
■ Type A
■Type B

655
Driving your vehicle
Move the lever up (to RES+) andrelease it immediately. The cruising
speed will increase by 2 km/h (1
mph) each time you move the lever
up (to RES+) in this manner. To decrease the cruising speed:
Follow either of these procedures:
Move the lever down (to SET-) and
hold it. Your vehicle will gradually
slow down. Release the lever at the
speed you want to maintain. Move the lever down (to SET-) and
release it immediately. The cruising
speed will decrease by 2 km/h (1
mph) each time you move the lever
down (to SET-) in this manner.
OHM056057L
OHM056056L
■Type A
■Type B

Driving your vehicle
56
6
To temporarily accelerate with
the cruise control on:
If you want to speed up temporarily
when the cruise control is on,
depress the accelerator pedal.
Increased speed will not interfere
with cruise control operation orchange the set speed.
To return to the set speed, take your
foot off the accelerator pedal. To cancel cruise control, do
one of the following:
Depress the brake pedal.
Shift into N (Neutral) with an auto-
matic transaxle.
Press the CANCEL/O button locat- ed on the steering wheel. Decrease the vehicle speed lower
than the memory speed by approx- imately 15 km/h (9 mph).
Decrease the vehicle speed to less than approximately 40 km/h (25mph).
Each of these actions will cancel
cruise control operation (the
cruise
set
indicator light will go off), but it
will not turn the system off. If you wish to resume cruise control opera-tion, move up the lever (to RES+)located on your steering wheel. You will return to your previously presetspeed.
OHM056061L
OHM056060L
■ Type A
■Type B

657
Driving your vehicle
To resume cruising speed at
more than approximately 40km/h (25 mph).If any method other than the
CRUISE / button was used to
cancel cruising speed and the sys-
tem is still activated, the most recentset speed will automatically resume
when the RES+ switch is pushed.
It will not resume, however, if the
vehicle speed has dropped below
approximately 40 km/h (25 mph).To turn cruise control off, do
one of the following:
Press the CRUISE/ button (the
cruise indicator light will be turn off).
Turn the ignition off.
Both of these actions cancel cruise control operation. If you want toresume cruise control operation,repeat the steps provided in “To set cruise control speed” on the previouspage.
OHM056058L
OHM056059L
■ Type A
■Type B

Driving your vehicle
58
6
This system detects the lane with the sensor at the front windshield and
warns you when your vehicle leaves
the lane.
LANE DEPARTURE WARNING SYSTEM (LDWS) (IF EQUIPPED)
WARNING
The LDWS does not make the vehicle change lanes. It is the
driver's responsibility to always
check the road conditions.
Do not turn the steering wheel suddenly, when the LDWS
warns you that your vehicle is
leaving the lane.
If the sensor can not detect the lane or if the vehicle speed
does not exceed around
60km/h, the LDWS won't warn
you even though the vehicle
leaves the lane.
If your vehicle has window tint or other types of coating and
accessory on the front wind-
shield, the LDWS may not
work properly.
(Continued)
(Continued)
Do not let water or any kind ofliquid come in contact with
the LDWS sensor.
Do not remove the LDWS parts and do not affect the
sensor by a strong impact.
Do not put objects that reflect light on the dash board.
Always check road conditions because you may not hear the
warning chime because of
audio and external condi-tions.
OHM056062L
OUM054149
OHM056063L

659
Driving your vehicle
To operate the LDWS, press the
switch with the ignition in the ON
position. The indicator illuminates
white on the cluster.
To cancel the LDWS, press LDWS
button again. The indicator on the
cluster will go off.If you select this symbol, the LDWS
mode on the LCD display will appear.
If your vehicle leaves the lane when
the LDWS is operating and vehicle
speed exceeds around 60km/h, the
warning operates as follows:1. Visual warning
If you leave a lane, the lane you
cross will blink (yellow) and LDWS
indicator will blink green on LCD dur-
ing max 3 seconds.
OHM056105L
OHM056107L
OHM056106L
■Left lane departure warning
■Right lane departure warning

Driving your vehicle
60
6
2. Auditory warning
If you leave the lane, the warning
sound operates for maximum 3 sec-
onds. The color of symbol will change
depend on the condition of LDWSsystem.
- White color : When you activate the
lane departure warn-
ing system by press-
ing the LDWS button,
system operating con-ditions are not satis-fied or the sensor doesnot detect the lane line
- Green color : When you activate the
lane departure warn-
ing system by press-
ing the LDWS button,
system operating con-ditions are satisfiedand the sensor detectthe lane line
- Yellow color : when there is a mal- function with the lane
departure warningsystem. Warning indicator
When the LDWS is not working prop-
erly, the warning light will illuminate
and the warning message will come
on for a few second. After the mes-
sage disappears, the master warning
light will illuminate. We recommend that the system be
checked by an authorized Kia dealer.
OHM056108L
OHM056109L