2017 JEEP RENEGADE light

Replacing Exterior Bulbs
Headlamps
Hi/Lo Beam Light Halogen
To replace the bulbs proceed as follows:
1. Open the engine compartment and remove the head-lamp bulb cap.
2. Rotate the headlamp bulb socket counterclockwise then pull outwards. 3. Push on the locking tab on the headlamp bulb connector
and remove the bulb and socket.
Headlamp Bulb Cap
Headlamp Bulb Socket
320 IN CASE OF EMERGENCY

Position Lights/Daytime Running Lights/Fog Lights
To replace the bulbs proceed as follows:
1. Turn the front wheels completely.
2. Use a suitable tool to remove the access door.
3. Remove the electrical connectors.4. Rotate in a counterclockwise direction (on the left-hand
socket) or in a clockwise direction (on the right-hand
socket) and remove the bulb and bulb socket.
Position Light/Daytime Running Light/Fog Light Access
1 — Screws
2 — Access Door
Electrical Connectors
322 IN CASE OF EMERGENCY

5. To replace the bulb gently push bulb and rotate coun-terclockwise. 6. Insert the new bulb by pushing on it and turning it
clockwise. Make sure the bulb is correctly locked in
place.
7. Install the bulb and sockets and rotate them clockwise (right side) and clockwise (left side), making sure that it
is properly locked.
8. Reconnect the electrical connectors.
Position Light/Daytime Running Light Assembly
1 — DRL Bulb Socket
2 — Turn Signal Bulb Socket
Bulb and Socket Assembly
1 — Bulb
2 — Rotate Bulb
7
IN CASE OF EMERGENCY 323

9. Reinstall the access door.
Front Fog Lights
To replace the bulbs proceed as follows:
1. Turn the front wheels completely.
2. Use a suitable tool to remove the access door.
3. By pushing the electrical connector tab remove theelectrical connector. 4. Rotate the bulb counterclockwise, and then replace the
bulb.
5. Insert the new bulb in the socket, making sure the bulb is locked into place.
6. Reconnect the electrical connector.
7. Reinstall the access door.
Position Light/Daytime Running Light/Fog Light Access
1 — Screws
2 — Access Door
Fog Light Assembly
1 — Bulb Socket
2 — Electrical Connector
3 — Bulb
324 IN CASE OF EMERGENCY

Rear Tail Lamps
Contain the following:
•Position lights
• Stop lights
• Direction indicator
• REVERSE lights
To replace the bulbs proceed as follows:
1. Open the liftgate.
2. Using a suitable tool remove the door as shown. 3. Using a suitable tool remove fastener.
4. Disconnect the electrical connector by pushing the re-
lease.
Trim Panel Door
Rear Lamp Fastener and Electrical Connector
1 — Fastener
2 — Electrical Connector
330 IN CASE OF EMERGENCY

7. Replace the bulb as necessary.
8. Insert the new bulb, making sure it is properly locked.
9. Reassemble the lamp assembly on the rear tail lamphousing, tightening the screws.
10. Reposition the rear tail lamp on the car.
11. Secure the fastener of the rear tail lamp and reconnect the electrical connector. 12. Reinstall the door making sure of its correct locked.
13. Finally close the tailgate.
Center High Mounted Stop Lamp (CHMSL)
The CHMSL is LED. For replacement see your authorized
dealer.
License Plate Lights
To replace the bulbs proceed as follows:
1. Using a suitable tool remove the license plate lens.
Rear Tail Lamp Holder
1 — Tail Light
2 — Reverse Bulb
3 — Position Light/Stop Light/Turn Signal
License Plate Light Location
332 IN CASE OF EMERGENCY

2. Remove the bulbs from the individual side contacts.
3. Insert the new bulbs, and ensure that they are properlylocked between the contacts.
4. Reinstall the license plate lens.
NOTE: If removal the license plate lens using a screw-
driver, be sure to cover the tip of the screwdriver with a
cloth so no damage is done to the lenses or the vehicle
paint.
Replacing Interior Bulbs
Front Courtesy Light
To replace the bulbs proceed as follows:
1. Using a suitable tool remove the front courtesy light as shown.
License Plate Light
Front Courtesy Light Housing
7
IN CASE OF EMERGENCY 333

2. Release the retainer clips and bulb housing as shown.
3. Replace the bulbs by pulling straight out of bulb hous-ing. 4. Insert the new bulbs, making sure that they are properly
locked.
5. Reassemble the bulb housing and courtesy light housing making sure that they are properly locked.
6. Install the front courtesy light making sure that it is properly locked.
Front Courtesy Bulb Housing
1 — Retaining Clips
2 — Bulb Housing
Front Courtesy Bulb Housing
334 IN CASE OF EMERGENCY