2017 INFINITI QX30 clock setting

Seat belt reminder chime
A chime will sound for approximately 120 sec-
onds if the vehicle’s speed exceeds 16 MPH (25
km/h) and the driver’s seat belt or front pas-
senger’s seat belt, if occupied is not securely
fastened. SeeSeat belt warning lightin the1.
Safety — seats, seat belts and supplemental
restraint systemsection.
Idle Stop/Start System reminder
chime (if equipped)
The engine will shift to the normal stopped
state if any of the following operations is made
during Idle Stop/Start System activation, and
the Idle Stop/Start System chime will sound if:
– The vehicle engine hood is open.
When the above condition continues for over 3
minutes the Idle Stop/Start System chime will
sound in 5-minute intervals as a reminder to
prevent the possibility of a discharged battery.
Use the ignition switch to turn off the engine.
Close the hood or the driver’s door, or fasten
the seat belt then restart the engine using the
ignition switch.
For more information, seeIdle Stop/Start
System (if equipped)in the5. Starting and
drivingsection.The vehicle information display1is located
between the tachometer and the speedometer.1Permanent display: depending on ve-
hicle specification: outside temperature
or speed
2Time
3Text field
4Menu bar
5Drive program
6Shift lever position
Text field
3shows the selected menu or
submenu as well as display messages.
NOTE
Set the time using the INFINITI controller and the
[Settings] menu available in the central display
(seeClock settingsin the4. Display screen,
heater and air conditioner, and audio system
section).
NIC2751NIC2752
VEHICLE INFORMATION DISPLAY
Instruments and controls2-15

Opening and closing
Manual control:
To close the sunshade, press and hold the
“CLOSE” side of the switch
1To stop the
sunshade from closing fully, release the switch.
To open the sunshade press and hold the
“OPEN” side of the switch
2To stop the
sunshade from opening fully, release the
switch.
Automatic operation
:
To fully open or close the sunshade automati-
cally, press briefly on the open or close side of
the switch and then release. To stop the sun-
shade from opening or closing, press either
side of the switch.
Auto-reverse function
:
When the control unit detects something caught
by the sunshade, the sunshade will open auto-
matically.
NOTE
The auto-reverse function remains active
whether the sunshade is being closed manually
or automatically.If the battery cable is disconnected, the clock
will need to be re-adjusted to the correct time.
ADJUSTING TIME
Set the time using the INFINITI controller and
the [Settings] menu available in the central
display (seeClock settingsin the4. Display
screen, heater and air conditioner, and audio
systemsection).
NOTE
On vehicles fitted with a navigation system, the
clock is automatically updated via GPS. The ini-
tial clock setting may be incorrect.
In the center console (LHD) Rear console Lug-
gage compartment
The power outlet is used for powering electrical
accessories such as a cellular telephone.
An emergency cut-off ensures that the on-board
voltage does not drop too low. If the on board
voltage is too low, the power to the sockets is
automatically cut. This ensures that there is
sufficient power to start the engine.
NSD619NIC2690
CLOCK POWER OUTLET
Instruments and controls2-75

Clock settings
Clock settings can be changed.
1. Push

AIR CONDITIONING SYSTEM
1Sets the temperature
2De-ices/defogs the windshield
3Set the air distribution
4Activates/deactivates air-recirculation
mode
5Sets the airflow
6Activates/deactivates cooling with air
dehumidification
7Switches the rear window defroster on/
off
Operating tips
A number of tips and recommendations for
optimum use of the air-conditioning system are
listed below:
•Switch on the air-conditioning system by
turning control knob
5clockwise to the
desired position (except position0)
•Set the temperature to 70oF (22oC)
•Recommendation for avoiding misted win-
dows at low exterior temperatures or in rain:
switch on the
cooling with dehumidi-
fication function. Set air distribution to
and if possible switch offand. Deactivate air-recirculation mode.
Set airflow control
5to a setting between 3
and 6.
•Recommendation for rapid cooling or heat-
ing of the vehicle interior: briefly set airflow
control
5to a setting between 3 and 6.
•Recommendation for a constant vehicle in-
terior temperature: set airflow control
5to a
setting between 1 and 3.
NAA1644
4-44Display screen, heater and air conditioner, and audio system

•Recommendation for air distribution in win-
ter: select theandsettings.
Recommendation for air distribution in sum-
mer: select the
orandsettings.
•Only use theWindshield demistingfunc-
tion briefly until the windshield is clear again
•Only use air-recirculation mode briefly, e. g
if there are unpleasant outside odors or
when in a tunnel. The windows could other-
wise mist up as no fresh air is drawn into the
vehicle in air-recirculation mode
•If you change the settings of the climate
control system, the climate status display
appears for approximately three seconds at
the bottom of the screen in the central
display (see separate operating instruc-
tions). You will see the current settings of the
various climate control functions.
Switching air-conditioning system
on/off
Make sure the ignition switch is in the ON
position.
To switch on:turn control
5clockwise to the
desired position (except position0).
To switch off:turn control
5counter-clockwise
to position0.
Activating/deactivating the cooling
with air dehumidification function
If you deactivate theCooling with air dehumidi-
ficationfunction, the air inside the vehicle will
not be cooled. The air inside the vehicle will
also not be dehumidified. The windows can mist
up more quickly. Therefore, only deactivate the
Cooling with air dehumidificationfunction
briefly.
TheCooling with air dehumidificationfunction
is only available when the engine is running.
The air inside the vehicle is cooled and dehu-
midified according to the temperature selected.
Condensation may drip from the underside of
the vehicle when cooling mode is active. This is
normal and not a sign that there is a malfunc-
tion.
To activate
:
Press thebutton The indicator lamp in
thebutton lights up.
To deactivate
:
Press thebutton. The indicator lamp in
thebutton goes out. The cooling with air
dehumidification function has a delayed switch-
off feature.Problems with theCooling with air dehumidifi-
cationfunction
:
Problem:The indicator lamp in thebutton flashes three times or remains off. The
cooling with air dehumidification function can-
not be activated.
Cause and solution:The cooling with air dehu-
midification function has been deactivated due
to a malfunction. Have the system checked. It is
recommended you visit an INFINITI retailer for
this service.
Setting the temperature
You can set the temperature for the entire
vehicle. The set temperature is automatically
maintained at a constant level.
To increase or reduce the temperature: turn
control
1counterclockwise or clockwise. Only
change the temperature setting in small incre-
ments. Start at 70
oF (22oC).
Setting the air distribution
Directs the airflow through the demis-
ter ventilators.
Directs the airflow through the center
and side air ventilators.
Directs the airflow through the footwell
air ventilators.
Display screen, heater and air conditioner, and audio system4-45

NOTE
•You can also activate several of the air
distribution settings simultaneously. In order
to do this, press several of the air distribu-
tion buttons. The air is then routed through
different air ventilators.
•Regardless of the air distribution setting,
airflow is always directed through the side
air ventilators. The side air ventilators can
only be closed if the adjusters are turned
clockwise until they engage.
To set air distribution:
1. Make sure the engine is running.
2. Press one or more of the
,,orbuttons. The corresponding indicator
lamp comes on.
Setting the airflow
1. Make sure the ignition switch is in the ON
position.
2. To increase or reduce airflow: turn control
5counterclockwise or clockwise.
Defogging the windshield
You can use this function to de-ice the wind-
shield or to defog the inside of the windshield
and the side windows.NOTE
You should only select theWindshield demist-
ingfunction until the windshield is clear again.
Activating theWindshield demistingfunction
:
Make sure the ignition switch is in the ON
position.
To activate: press the
button The indica-
tor light in thebutton lights up.
The climate control system switches to the
following functions:
•High airflow
•High temperature
•Air distribution to the windshield and front
side windows
•Air-recirculation mode off
NOTE
•TheWindshield demistingfunction auto-
matically sets the blower output to the opti-
mum demisting effect. As a result, the airflow
may increase or decrease automatically after
the
button is pressed.
•You can adjust the blower output manually
while theWindshield demistingfunction is
in operation. Turn airflow control
5counter-
clockwise or clockwise.Deactivating theWindshield demistingfunc-
tion
:
Press thebutton. The indicator lamp in
thebutton goes out. The previous set-
tings are reactivated. Air-recirculation mode
remains deactivated.
or
Turn temperature control
1counterclockwise
or clockwise.
Defogging the windows
Windows misted up on the inside:
1. Activate theCooling with air dehu-
midificationfunction.
2. If the windows continue to mist up, activate
the
Windshield demistingfunction.
NOTE
You should only select this setting until the
windshield is clear again.
Windows misted up on the outside
:
1. Activate the windshield wipers.
2. Set the air distribution to
or.
NOTE
You should only select this setting until the win-
dows are clear again.
4-46Display screen, heater and air conditioner, and audio system

Setting automatic climate control to
automatic mode
Only automatic climate control features the
Control climate control automaticallyfunction.
In automatic mode, the set temperature is
maintained automatically at a constant level
The system automatically regulates the tem-
perature of the dispensed air, the airflow and
the air distribution.
The automatic mode functions optimally when
theCooling with air dehumidificationfunction
is activated. If desired, cooling with air dehu-
midification can be deactivated.
If you deactivate theCooling with air-
dehumidificationfunction, the air inside the
vehicle will not be cooled. The air inside the
vehicle will also not be dehumidified. The win-
dows can mist up more quickly. Therefore, only
deactivate theCooling with air-
dehumidificationfunction briefly.
To set climate control to automatic mode
:
Make sure the ignition switch is in the ON
position.
Set the desired temperature.
To activate: press the
button The indica-
tor lamp in thebutton lights up. Auto-
matic air distribution and airflow are activated.To switch to manual mode: press the
orbutton
or
Press the
orbutton. The indicator
lamp in thebutton goes out. Automatic
air distribution and airflow are deactivated.
Setting the temperature
Different temperatures can be set for the driv-
er’s and front-passenger sides. The set tem-
perature is automatically maintained at a con-
stant level.
Make sure the ignition switch is in the ON
position.
To increase or reduce temperature: turn control
1or9counterclockwise or clockwise. Only
change the temperature setting in small incre-
ments. Start at 70
oF (22oC).
Setting the air distribution
Directs the airflow through the demis-
ter ventilators.
Directs the airflow through the center
and side air ventilators.
Directs the airflow through the footwell
air ventilators.
Directs the airflow through the center
and side air ventilators as well as the
footwell air ventilators.
Directs the airflow through the center
and side air ventilators as well as the
demister ventilators.
Directs the airflow through the footwell
and demister ventilators.
Directs the airflow through the demis-
ter ventilators, the center and side air
ventilators as well as the footwell air
ventilators.
NOTE
Regardless of the air distribution setting, airflow
is always directed through the side air ventila-
tors. The side air ventilators can only be closed if
the adjusters are turned clockwise until they
engage.
To set the air distribution:
1. Make sure the engine is running.
2. Press the
orbutton repeatedly
until the desired symbol appears in the
display.
Setting the airflow
1. Make sure the ignition switch is in the ON
position.
2. To increase or reduce airflow: press the
orbutton.
4-50Display screen, heater and air conditioner, and audio system

Switching the ZONE function on/off
This function is only available with automatic
climate control.
To activate:press the
button. The indi-
cator light in thebutton lights up. The
temperature setting for the driver’s side is not
adopted for the front-passenger side.
To deactivate:press the
button. The
indicator lamp in thebutton goes out.
The temperature setting for the driver’s side is
adopted for the front-passenger side.
Defogging the windshield
You can use this function to de-ice the wind-
shield or to defog the inside of the windshield
and the side windows.
NOTE
You should only select theWindshield demist-
ingfunction until the windshield is clear again.
Activating theWindshield demistingfunction
:
Make sure the ignition switch is in the ON
position.
To activate: press the
button The indica-
tor light in thebutton lights up.The climate control system switches to the
following functions:
•High airflow
•High temperature
•Air distribution to the windshield and front
side windows
•Air-recirculation mode off
NOTE
•TheWindshield demistingfunction auto-
matically sets the blower output to the opti-
mum demisting effect. As a result, the airflow
may increase or decrease automatically after
the
button is pressed.
•You can adjust the blower output manually
while theWindshield demistingfunction is
in operation. Press the
orbutton.
Deactivating theWindshield demistingfunction:
Press thebutton. The indicator lamp in
thebutton goes out. The previous set-
tings are reactivated Air-recirculation mode re-
mains deactivated.
or
Turn temperature control
1or9counter-
clockwise or clockwise.
Defogging the windows
Windows misted up on the inside:
1. Activate theCooling with air dehu-
midificationfunction.
2. Activate automatic mode
.
3. If the windows continue to mist up, activate
the
Windshield demistingfunction.
NOTE
You should only select this setting until the
windshield is clear again.
Windows misted up on the outside
:
1. Activate the windshield wipers.
2. Set the air distribution to
or.
NOTE
You should only select this setting until the win-
dows are clear again.
Air recirculation mode
You can deactivate the flow of fresh air if
unpleasant odors are entering the vehicle from
outside. The air already inside the vehicle will
then be recirculated.
If you activate air-recirculation mode, the windows
can mist up more quickly, in particular at low
temperatures. Only use air recirculation mode
briefly to prevent the windows misting up.
Display screen, heater and air conditioner, and audio system4-51