2017 INFINITI QX30 recommended oil

1. Park the vehicle on a level surface and apply
the parking brake.
2. Start the engine and let it idle until it
reaches the normal operating temperature,
then turn it off.
3. Remove the oil filler cap by turning it
counterclockwise.
4. Remove the engine undershield.
5. Place a large drain pan under the drain plug.
6. Remove the drain plug with a wrench by
turning it counterclockwise and completely
drain the oil. If the oil filter is to be changed,
remove and replace it at this time. For
additional information, refer toChanging
engine oil filterlater in this section.
•Waste oil must be disposed of properly.
•Check your local regulations.
7. Clean and reinstall the drain plug and a new
washer. Securely tighten the drain plug with
a wrench. Do not use excessive force. Drain
plug tightening torque: 22 ft-lb, 30 N•m
8. Refill engine with recommended oil through
the oil filler opening, then install the oil filler
cap securely.
For additional information on drain and refill
capacity, refer toRecommended fluids/
lubricants and capacitiesin the9. Maintenance
and Schedulessection.
The drain and refill capacity depends on the
oil temperature and drain time. Use these
specifications for reference only. Always use
the dipstick to determine when the proper
amount of oil is in the engine.
9. Start the engine. Check for leakage around
the drain plug and oil filter. Correct as
required.
10. Turn the engine off and wait more than 10
minutes. Check the oil level with the dip-
stick. Add engine oil if necessary.
CHANGING ENGINE OIL FILTER
1. Park the vehicle on a level surface and apply
the parking brake.
2. Turn the engine off.
3. Place a large drain pan under the oil filter
1.
4. Loosen the oil filter
1with an oil filter
wrench by turning it counterclockwise. Then
remove the oil filter by turning it by hand.
CAUTION
Be careful not to burn yourself. The engine oil
may be hot.
5. Wipe the engine oil filter sealing surface
with a clean rag.
NDI1622NDI16102.0L gasoline engine
8-6Do-it-yourself

CAUTION
•Be sure to remove any old gasket material
remaining on the sealing surface of the en-
gine. Failure to do so could lead to an oil
leak and engine damage.
•The dipstick must be inserted in place to
prevent oil spillage from the dipstick hole
when filling the engine with oil.
6. Coat the gasket on the new filter with clean
engine oil.
7. Screw on the oil filter until a slight resis-
tance is felt, then tighten an additional 2/3
turn. Engine oil filter tightening torque: 19
ft-lb, 25 N•m
8. Start the engine and check for leakage
around the oil filter. Correct as required.
9. Turn the engine off and wait more than 10
minutes. Check the oil level. Add engine oil
if necessary.It is recommended that you visit an INFINITI
retailer if checking or replacement is required.
CAUTION
•Use only Shell DCT-M1 or equivalent. Do not
mix with other fluids.
•Using automatic transmission fluid other
than Shell DCT-M1 may cause deterioration
in driveability and automatic transmission
durability, and may damage the automatic
transmission. Damage caused by the use of
fluids other than as recommended is not
covered by the warranty.
WARNING
•Use only new fluid. Old, inferior, or contami-
nated fluid may damage the brake systems.
The use of improper fluids can damage the
brake system and affect the vehicle’s stop-
ping ability.
•Clean the filler cap before removing.
•Brake fluid is poisonous and should be
stored carefully in marked containers out of
the reach of children.
CAUTION
•Do not spill the fluid on painted surfaces.
This will damage the paint. If fluid is spilled,
wash with water.
NDI1599
AUTOMATIC TRANSMISSION FLUID (ATF) BRAKE FLUID
Do-it-yourself8-7

Parking brake*:
Check the parking brake operation regularly.
Also make sure that the vehicle is held securely
on a fairly steep hill when only the parking
brake is applied. If the parking brake needs
adjustment, it is recommended you visit an
INFINITI retailer for this service.
Seats
:
Check seat position controls such as seat ad-
justers, seatback recliner, etc. to ensure they
operate smoothly and that all latches lock
securely in every position. Check that the head
restraints move up and down smoothly and that
the locks (if so equipped) hold securely in all
latched positions.
Seat belts
:
Check that all parts of the seat belt system (for
example, buckles, anchors, adjusters and re-
tractors) operate properly and smoothly, and
are installed securely. Check the belt webbing
for cuts, fraying, wear or damage.
Steering wheel
:
Check for changes in the steering condition,
such as excessive free play, hard steering or
strange noises.Warning lights and chimes
:
Make sure that all warning lights and chimes
are operating properly.
Windshield defroster
:
Check that the air comes out of the defroster
outlets properly and in good quantity when
operating the heater or air conditioner.
Windshield wiper and washer*
:
Check that the wipers and washer operate
properly and that the wipers do not streak.
Under the hood and vehicle
The maintenance items listed here should be
checked periodically (for example, each time
you check the engine oil or refuel).
Battery*
:
Except for maintenance free battery, check the
fluid level in each cell. It should be between the
“UPPER” and “LOWER” lines. Vehicles operated
in high temperatures or under severe condi-
tions require frequent checks of the battery
fluid level.NOTE
Care should be taken to avoid situations that can
lead to potential battery discharge and potential
no-start conditions such as:
1. Installation or extended use of electronic ac-
cessories that consume battery power when
the engine is not running (Phone chargers,
GPS, DVD players, etc.)
2. Vehicle is not driven regularly and/or only
driven short distances.
In these cases, the battery may need to be
charged to maintain battery health.
Brake fluid level*
:
Make sure that the brake fluid level is between
the “MAX” and “MIN” lines on the reservoir.
Coolant level*
:
Check the coolant level when the engine is cold.
Engine drive belt(s)*
:
Make sure that no belt is frayed, worn, cracked
or oily.
Engine oil level*
:
Check the level after parking the vehicle on a
level spot and turning off the engine. Wait more
than 15 minutes for the oil to drain back into the
oil pan.
9-4Maintenance and Schedules

Exhaust system:
Make sure there are no loose supports, cracks
or holes. If the sound of the exhaust seems
unusual or there is a smell of exhaust fumes,
immediately have the exhaust system in-
spected. It is recommended you visit an INFINITI
retailer for this service. SeePrecautions when
starting and drivingin the5. Starting and
drivingsection.
Fluid leaks
:
Check under the vehicle for fuel, oil, water or
other fluid leaks after the vehicle has been
parked for a while. Water dripping from the air
conditioner after use is normal. If you should
notice any leaks or if gasoline fumes are evi-
dent, check for the cause and have it corrected
immediately.
Radiator and hoses
:
Check the front of the radiator and clean off any
dirt, insects, leaves, etc., that may have accu-
mulated. Make sure the hoses have no cracks,
deformation, rot or loose connections.
Underbody
:
The underbody is frequently exposed to corro-
sive substances such as those used on icy
roads or to control dust. It is very important to
remove these substances, otherwise rust willform on the floor pan, frame, fuel lines and
around the exhaust system. At the end of
winter, the underbody should be thoroughly
flushed with plain water, being careful to clean
those areas where mud and dirt may accumu-
late. For additional information, seeCleaning
exteriorin the7. Appearance and caresec-
tion.
Windshield washer fluid*
:
Check that there is adequate fluid in the reser-
voir.The following descriptions are provided to give
you a better understanding of the scheduled
maintenance items that should be regularly
checked or replaced. The maintenance schedule
indicates at which mileage/time intervals each
item requires service.
In addition to scheduled maintenance, your
vehicle requires that some items be checked
during normal day-to-day operation. Refer to
General maintenancein this section.
Items marked with “*” are recommended by
INFINITI for reliable vehicle operation. You are
not required to perform maintenance on these
items in order to maintain the warranties which
come with your vehicle. Other maintenance
items and intervals are required.
When applicable, additional information can be
found in the “Do-it-yourself” section in Chapter
8.
NOTE
INFINITI does not advocate the use of non-OEM
approved aftermarket flushing systems and
strongly advises against performing these ser-
vices on an INFINITI product. Many of the after-
market flushing systems use non-OEM approved
chemicals or solvents, the use of which has not
been validated by INFINITI.
EXPLANATION OF GENERAL MAINTENANCE
ITEMS
Maintenance and Schedules9-5

For recommended fuel, lubricants, fluids,
grease, and refrigerant, refer toRecommended
fluids/lubricants and capacitiesin the10.
Technical informationTechnical information
section.
EMISSION CONTROL SYSTEM
MAINTENANCE
Drive belts*:
Check engine drive belts for wear, fraying or
cracking and for proper tension. Replace any
damaged drive belts
Engine air filter*:
Replace at specified intervals. When driving for
prolonged periods in dusty conditions, check/
replace the filter more frequently.
Engine coolant*:
Replace coolant at the specified interval. When
adding or replacing coolant, be sure to use only
Genuine INFINITI Engine Coolant or equivalent
in its quality (BASF Glysantin® G40®). (For
additional information, refer toEngine cooling
systemin the9. Maintenance and Schedules
section.)NOTE
Mixing any other type of coolant or the use of
non-distilled water may reduce the recom-
mended service interval of the coolant.
Engine oil and oil filter:
Replace engine oil and oil filter at the specified
intervals. For recommended oil grade and vis-
cosity refer toRecommended fluids/lubricants
and capacitiesin the10. Technical informa-
tionsection.
Fuel filter:
Replace the fuel filter and drain the water at the
specified intervals.
Fuel lines*:
Check the fuel hoses, piping and connections
for leaks, looseness, or deterioration. Tighten
connections or replace parts as necessary.
Spark plugs:
Replace at specified intervals. Install new plugs
of the type as originally equipped.
CHASSIS AND BODY MAINTENANCE
Brake lines and cables:
Visually inspect for proper installation. Check
for chafing, cracks, deterioration, and signs of
leaking. Replace any deteriorated or damaged
parts immediately.
Brake pads, rotors, drums, & linings:
Check for wear, deterioration and fluid leaks.
Replace any deteriorated or damaged parts
immediately.
Exhaust system:
Visually inspect the exhaust pipes, muffler and
hangers for leaks, cracks, deterioration, and
damage. Tighten connections or replace parts
as necessary.
In-cabin microfilter:
Replace at specified intervals. When driving for
prolonged periods in dusty conditions, replace
the filter more frequently.
Propeller shaft(s):
Check for damage, looseness, and grease leak-
age. (4WD/AWD).
9-6Maintenance and Schedules

The following tables show the standard maintenance schedule. Depending upon weather and atmospheric conditions, varying road surfaces, individual
driving habits and vehicle usage, additional or more frequent maintenance may be required. After 120,000 miles (192,000 km)/144 months, continue
maintenance at the same mileage/time intervals.
EMISSION CONTROL SYSTEM MAINTENANCE (FOR 2.0L TURBO GASOLINE ENGINE)
Abbreviations: I = Inspect and correct or replace as necessary, R = Replace
MAINTENANCE OPERATIONmiles x 1,000MAINTENANCE INTERVAL
Perform at number of miles,
kilometers or months, whichever
comes first.51015202530354045505560
(km x 1,000) (8) (16) (24) (32) (40) (48) (56) (64) (72) (80) (88) (96)
months 6 12 18 24 30 36 42 48 54 60 66 72
Engine compartment See NOTE (1)
V-belt See NOTE (2) I* I* I*
Replace every 155,000 miles or 180 months
Air cleaner filter Replace every 45,000 miles or 48 months
Fuel lines I* I* I*
Fuel filter See NOTE (3)
Engine coolant* Replace every 155,000 miles or 180 months
Engine oil R R R R R R
Engine oil filter R R R R R R
Spark plugs Replace every 45,000 miles or 48 months
NOTE:
(1) All visible parts checked for leaks and damage.
(2) In visible area only.
(3) Maintenance-free item.
* Maintenance items and intervals with ”*” are recommended by INFINITI for reliable vehicle operation. The owner need not perform such maintenance
in order to maintain the emission warranty or manufacturer recall liability. Other maintenance items and intervals are required
STANDARD MAINTENANCE
9-10Maintenance and Schedules

Abbreviations: I = Inspect and correct or replace as necessary, R = Replace
MAINTENANCE OPERATIONmiles x 1,000MAINTENANCE INTERVAL
Perform at number of miles, kilome-
ters or months, whichever comes
first.65 70 75 80 85 90 95 100 105 110 115 120
(km x 1,000) (104) (112) (120) (128) (136) (144) (152) (160) (168) (176) (184) (192)
months 78 84 90 96 102 108 114 120 126 132 138 144
Engine compartment See NOTE (1)
V-belt See NOTE (2) I* I* I*
Replace every 155,000 miles or 180 months
Air cleaner filter Replace every 45,000 miles or 48 months
Fuel lines I* I* I*
Fuel filter See NOTE (3)
Engine coolant* Replace every 155,000 miles or 180 months
Engine oil R R R R R R
Engine oil filter R R R R R R
Spark plugs Replace every 45,000 miles or 48 months
NOTE:
(1) All visible parts checked for leaks and damage.
(2) In visible area only.
(3) Maintenance-free item.
* Maintenance items and intervals with ”*” are recommended by INFINITI for reliable vehicle operation. The owner need not perform such maintenance
in order to maintain the emission warranty or manufacturer recall liability. Other maintenance items and intervals are required
Maintenance and Schedules9-11

10 Technical information
Recommended fluids/lubricants and capacities. . . .10-2
Fuel recommendation..................10-3
Engine oil and oil filter recommendations......10-5
Air conditioner system refrigerant and oil
recommendations....................10-6
Engine specifications....................10-7
Wheels and Tires......................10-8
Dimensions..........................10-9
When traveling or registering in another country . . .10-10
Vehicle identification....................10-10
Vehicle identification number (VIN) plate....10-10
Vehicle identification number (chassis number) . .10-11
Engine serial number..................10-11
F.M.V.S.S./C.M.V.S.S. Certification label......10-11
Emission control information label..........10-11
Tire and loading information label..........10-12
Air conditioner specification label..........10-12Installing front license plate...............10-13
Vehicle loading information................10-14
TERMS..........................10-14
Vehicle load capacity..................10-15
Loading tips.......................10-16
Measurement of weights...............10-16
Trailer towing........................10-16
Uniform tire quality grading................10-17
Treadwear........................10-17
Traction AA, A, B and C................10-17
Temperature A, B and C................10-17
Emission control system warranty............10-18
Reporting safety defects..................10-18
Readiness for inspection/maintenance (I/M) test . . .10-19
Event data recorders (EDR) (if so equipped)......10-20
Owner’s manual/service manual order information .10-20