2017 INFINITI QX30 battery

4. Repeatedly tap the key against your palmuntil battery
1falls out. 5. Insert the new battery with the positive
terminal facing upwards. Use a lint-free cloth
to do so.
6. Make sure that the surface of the battery is free of lint, grease and other contamination.
7. Insert the front tabs of battery cover
1and
then press to close it.
8. Insert emergency key element into the key (see Mechanical key in the3. Pre-driving
checks and adjustments section).
9. Check the function of all key buttons on the vehicle.
If you need assistance with replacement, it is
recommended that you visit an INFINITI retailer
for this service. FCC Notice:
For USA:
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harm-
ful interference, and (2) this device must accept
any interference received, including interfer-
ence that may cause undesired operation.
NOTE
Changes or modifications not expressly ap-
proved by the party responsible for compliance
could void the user’s authority to operate the
equipment.
For Canada:
This device complies with Industry Canada
license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this
device may not cause interference, and (2) this
device must accept any interference, including
interference that may cause undesired opera-
tion of the device.
NPA1473SPA0784Z
Do-it-yourself8-21

Low/High beam Headlight bulb replacement:
1. Open the hood. For details, seeHoodin the
3. Pre-driving checks and adjustments sec-
tion.
2. Disconnect the negative (—) battery cable.
3. Remove the corresponding access cover from the wheel arch.
4. Turn housing cover
1counterclockwise and
remove it.
5. Turn bulb holder
2counterclockwise and
pull out
6. Take the headlight bulb out of bulb holder
2.
7. Insert the new bulb into bulb holder
2.
8. Insert bulb holder
2and turn it clockwise. 9. Press on housing cover
1and turn it to the
right.
10. Replace the cover in the front wheel arch
11. Reconnect the negative (—) battery cable and close the hood.
NOTE
Fog may temporarily form inside the lens of the
exterior lights in the rain or in a car wash. The
fog is caused by a temperature difference be-
tween the inside and the outside of the lens. This
is not a malfunction. If large droplets can be
seen, it is recommended that you visit an
INFINITI retailer.
Front turn signal light bulb
replacement (non-LED system only)
1. Open the hood. For details, see Hoodin the
3. Pre-driving checks and adjustments sec-
tion.
2. Disconnect the negative (—) battery cable.
3. Turn housing cover
1counterclockwise and
remove it.
4. Turn bulb holder
2counterclockwise and
pull out
5. Take the headlight bulb out of bulb holder
2.
6. Insert the new bulb into bulb holder
2.
7. Insert bulb holder
2and turn it clockwise.
NDI1611NDI1612
Do-it-yourself8-25

8. Press on housing cover1and turn it to the
right.
9. Reconnect the negative (—) battery cable and close the hood. If you have a flat tire, refer to
Flat tirein the6.
In case of emergency section.
TIRE PRESSURE
Tire Pressure Monitoring System
(TPMS)
The Tire Pressure Monitoring System (TPMS)
monitors tire pressure of all tires. When the low
tire pressure warning light is lit, one or more of
the tires is significantly under-inflated.
The TPMS will activate only when the vehicle is
driven at speeds above 16 MPH (25 km/h). Also,
this system may not detect a sudden drop in tire
pressure (for example a flat tire while driving).
For additional information, refer to Tire Pres-
sure Monitoring System (TPMS) in the
5. Starting and driving section.
Tire inflation pressure
Check the tire pressures (including the spare)
often and always prior to long distance trips.
The recommended tire pressure specifications
are shown on the F.M.V.S.S./C.M.V.S.S. label or
the Tire and Loading Information label (if so
equipped) under the Cold Tire Pressure head-
ing. The Tire and Loading Information label is
affixed to the driver side center pillar. Tire pressures should be checked regularly be-
cause:
•Most tires naturally lose air over time.
•Tires can lose air suddenly when driven over
potholes or other objects or if the vehicle
strikes a curb while parking.
The tire pressures should be checked when the
tires are cold. The tires are considered COLD
after the vehicle has been parked for 3 or more
hours, or driven less than 1 mile (1.6 km) at
moderate speeds.
WARNING
•Improperly inflated tires can fail suddenly
and cause an accident.
•The Gross Vehicle Weight rating (GVWR) is
located on the F.M.V.S. S./C.M.V.S.S. certi-
fication label. The vehicle weight capacity is
indicated on the Tire and Loading Informa-
tion label (if so equipped). Do not load your
vehicle beyond this capacity. Overloading
your vehicle may result in reduced tire life,
unsafe operating conditions due to prema-
ture tire failure, or unfavorable handling
characteristics and could also lead to a se-
rious accident. Loading beyond the speci-
fied capacity may also result in failure of
other vehicle components.
WHEELS AND TIRES
8-26Do-it-yourself

Parking brake*:
Check the parking brake operation regularly.
Also make sure that the vehicle is held securely
on a fairly steep hill when only the parking
brake is applied. If the parking brake needs
adjustment, it is recommended you visit an
INFINITI retailer for this service.
Seats
:
Check seat position controls such as seat ad-
justers, seatback recliner, etc. to ensure they
operate smoothly and that all latches lock
securely in every position. Check that the head
restraints move up and down smoothly and that
the locks (if so equipped) hold securely in all
latched positions.
Seat belts
:
Check that all parts of the seat belt system (for
example, buckles, anchors, adjusters and re-
tractors) operate properly and smoothly, and
are installed securely. Check the belt webbing
for cuts, fraying, wear or damage.
Steering wheel
:
Check for changes in the steering condition,
such as excessive free play, hard steering or
strange noises.Warning lights and chimes
:
Make sure that all warning lights and chimes
are operating properly.
Windshield defroster
:
Check that the air comes out of the defroster
outlets properly and in good quantity when
operating the heater or air conditioner.
Windshield wiper and washer*
:
Check that the wipers and washer operate
properly and that the wipers do not streak.
Under the hood and vehicle
The maintenance items listed here should be
checked periodically (for example, each time
you check the engine oil or refuel).
Battery*
:
Except for maintenance free battery, check the
fluid level in each cell. It should be between the
“UPPER” and “LOWER” lines. Vehicles operated
in high temperatures or under severe condi-
tions require frequent checks of the battery
fluid level.
NOTE
Care should be taken to avoid situations that can
lead to potential battery discharge and potential
no-start conditions such as:
1. Installation or extended use of electronic ac-
cessories that consume battery power when
the engine is not running (Phone chargers,
GPS, DVD players, etc.)
2. Vehicle is not driven regularly and/or only driven short distances.
In these cases, the battery may need to be
charged to maintain battery health.
Brake fluid level*
:
Make sure that the brake fluid level is between
the “MAX” and “MIN” lines on the reservoir.
Coolant level*
:
Check the coolant level when the engine is cold.
Engine drive belt(s)*
:
Make sure that no belt is frayed, worn, cracked
or oily.
Engine oil level*
:
Check the level after parking the vehicle on a
level spot and turning off the engine. Wait more
than 15 minutes for the oil to drain back into the
oil pan.
9-4Maintenance and Schedules

The vehicle information display shows a service
message for a few seconds, e g:
•[Service A In .. days]
•[Service A Due]
•[Service A Exceeded by .. days]
Depending on the operating conditions of the
vehicle, the remaining time or distance until the
next service due date is displayed.
The letter indicates which service is due. A
stands for a minor service and B for a major
service. A number or another letter may be
displayed after the letter.
Only for certain countries: the position after the
letter A or B indicates any necessary additional
maintenance work. If you notify an INFINITI
retailer of this display, you will receive a state-
ment on the associated costs.
The maintenance service interval display does
not take into account any periods of time during
which the battery is disconnected.
Maintaining the time-dependent service sched-
ule:
Note down the service due date displayed in the
vehicle information display before disconnect-
ing the battery.
or After reconnecting the battery, subtract the
battery disconnection periods from the service
date shown on the display.
Hiding service messages
Press the orbutton on the steering
wheel.
Displaying service messages
1. Switch the ignition on.
2. Press the
orbutton on the
steering wheel to select the [Serv.] menu.
3. Press the
orbutton to select
[Maintenance] submenu and confirm by
pressing the OK button.
The service due date appears in the vehicle
information display.
Information about service
Resetting the maintenance service interval display:
CAUTION
If the maintenance service interval display has
been inadvertently reset, this setting can be
corrected at an INFINITI retailer.
Have service work carried out as described in
the Maintenance Schedule. This may other-
wise lead to increased wear and damage to the
major assemblies or the vehicle. An INFINITI retailer will reset the maintenance
service interval display after the service work
has been carried out. You can also obtain
further information on maintenance work, for
example.
Special service requirements
:
The prescribed service interval is based on
normal operation of the vehicle. Service work
will need to be performed more often if the
vehicle is operated under arduous conditions or
increased loads, for example:
•Regular city driving with frequent intermedi-
ate stops
•If the vehicle is primarily used to travel short
distance
•For frequent operation in mountainous ter-
rain or on poor road surfaces
•If the engine is often left idling for long
periods
In these or similar operating conditions, have,
for example, the air filter, engine oil and oil
filter changed more frequently. The tires must
be checked more frequently if the vehicle is
operated under increased loads. Further infor-
mation can be obtained at an INFINITI retailer.
9-8Maintenance and Schedules

CHASSIS & BODY MAINTENANCE
Abbreviations: I = Inspect and correct or replace as necessary, R = Replace
MAINTENANCE OPERATIONmiles x 1,000 MAINTENANCE INTERVAL
Perform at number of miles,
kilometers or months, whichever comes first. 51015202530354045505560
(km x 1,000) (8) (16) (24) (32) (40) (48) (56) (64) (72) (80) (88) (96) months 6 12 18 24 30 36 42 48 54 60 66 72
Brake lines and cables I I I I I I
Brake pads and rotors* II IIII
Brake fluid * RRR
Automatic transmission fluid III
Automatic transmission fluid and filter Replace every 60,000 miles or 60 months
Differential gear oil II IIII
Steering gear and linkage, axle and suspension parts* III
Tire rotation See NOTE (1)
Propeller shaft & drive shaft boots (4WD models)* IIIIII
Exhaust system* III
In-cabin microfilter RRR
I-key battery RRRR
NOTE:
(1) Refer to Tire rotation* earlier in this section.
Maintenance and Schedules9-11

Abbreviations: I = Inspect and correct or replace as necessary, R = Replace
MAINTENANCE OPERATIONmiles x
1,000 MAINTENANCE INTERVAL
Perform at number of miles, kilome-
ters or months, whichever comes first. 65 70 75 80 85 90 95 100 105 110 115 120
(km x 1,000) (104) (112) (120) (128) (136) (144) (152) (160) (168) (176) (184) (192) months 78 84 90 96 102 108 114 120 126 132 138 144
Brake lines and cables II II II
Brake pads and rotors* II II II
Brake fluid* RR R
Automatic transmission fluid II I
Automatic transmission fluid and filter Replace every 60,000 miles or 60 months
Differential gear oil II II II
Steering gear and linkage, axle and suspension parts* II I
Tire rotation See NOTE (1)
Propeller shaft & drive shaft boots (4WD models)* IIII I I
Exhaust system* II I
In-cabin microfilter RR R
I-key battery RRR R
NOTE:
(1) Refer to Tire rotation* earlier in this section.
* Maintenance items with “*” should be performed more frequently according to Maintenance under severe driving conditionslater in this section
9-12Maintenance and Schedules

For Canada:
If you believe that your vehicle has a defect
which could cause a crash or could cause injury
or death, you should immediately inform Trans-
port Canada in addition to notifying INFINITI.
If Transport Canada receives complaints, it may
open an investigation, and if it finds that a
safety defect exists in a group of vehicles, it
may request that INFINITI conduct a recall cam-
paign. However, Transport Canada cannot be-
come involved in individual problems between
you, your retailer, or INFINITI.
You may contact Transport Canada’s Defect
Investigations and Recalls Division toll free at
1-800-333- 0510. You may also report safety
defects online at:
https://wwwapps.tc.gc.ca/Saf-Sec- Sur/7/
PCDB-BDPP/Index.aspx.
Additional information concerning motor ve-
hicle safety may be obtained from Transport
Canada’s Road Safety Information Center at
1-800-333- 0371 or online at www.tc.gc.ca/
roadsafety (English speakers) or www.tc.gc.ca/
securiteroutiere (French speakers).
To notify INFINITI of any safety concerns please
contact our Consumer Information Center toll
free at 1-800- 361-4792.WARNING
A vehicle equipped with All-Wheel Drive (AWD)
should never be tested using a two wheel dy-
namometer (such as the dynamometers used
by some states for emissions testing), or simi-
lar equipment. Make sure you inform test facil-
ity personnel that your vehicle is equipped
with AWD before it is placed on a dynamom-
eter. Using the wrong test equipment may re-
sult in transmission damage or unexpected ve-
hicle movement which could result in serious
vehicle damage or personal injury.
Due to legal requirements in some states and
Canadian Provinces, your vehicle may be re-
quired to be in what is called the “ready
condition” for an Inspection/Maintenance (I/M)
test of the emission control system.
The vehicle is set to the “ready condition” when
it is driven through certain driving patterns.
Usually, the “ready condition” can be obtained
by ordinary usage of the vehicle.
If a powertrain system component is repaired or
the battery is disconnected, the vehicle may be
reset to a “not ready condition”. Before taking
the I/M test, check the vehicle’s inspection/
maintenance test readiness condition. Place the
ignition switch in the ON position without start- ing the engine. If the Malfunction Indicator Light
(MIL) comes on steady for 20 seconds and then
blinks for 10 seconds, the I/M test condition is
“not ready”. If the MIL does not blink after 20
seconds, the I/M test condition is “ready”.
It is recommended you contact an INFINITI re-
tailer to set the “ready condition” or to prepare
the vehicle for testing.
READINESS FOR INSPECTION/
MAINTENANCE (I/M) TEST
10-18Technical information