2017 INFINITI QX30 maintenance

SYSTEM MAINTENANCE
The sensor for the ICC systemAis located
behind the INFINITI logo at the front of the
vehicle.
To keep the ICC system operating properly, be
sure to observe the following:
•Always keep area around the sensor clean.
•Do not strike or damage the areas around the
sensor. Do not touch or remove the screw
located on the sensor. Doing so could cause
failure or malfunction. If the sensor is dam-
aged due to an accident, it is recommended
you contact an INFINITI retailer.
•Do not cover or attach stickers (including
transparent material) or install an accessory
near the sensor. This could cause failure or
malfunction.
Radio frequency statement
For USA:
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harm-
ful interference, and (2) this device must accept
any interference received, including interfer-
ence that may cause undesired operation.
NOTE
Changes or modification not expressly approved
by the party responsible for compliance could
void the user’s authority to operate the equip-
ment.
For Canada:
This device complies with Industry Canada
license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this
device may not cause harmful interference, and
(2) this device must accept any interference re-
ceived, including interference that may cause
undesired operation of the device.
WARNING
Failure to follow the warnings and instructions
for proper use of the FEB system could result in
serious personal injury or death.
•The FEB system is a supplemental aid to the
driver. It is not a replacement for the driver’s
attention to traffic conditions or responsi-
bility to drive safely. It cannot prevent acci-
dents due to carelessness or dangerous
driving techniques.
•The FEB system does not function in all driv-
ing, traffic, weather and road conditions.
The FEB system can assist the driver when there
is a risk of a forward collision with the vehicle
ahead in the traveling lane.
NSD645
FORWARD EMERGENCY BRAKING (FEB)
SYSTEM (IF EQUIPPED)
5-60Starting and driving

FEB SYSTEM LIMITATIONS
WARNING
Listed below are the system limitations for the
FEB system. Failure to operate the vehicle in
accordance with these system limitations
could result in serious injury or death.
•The FEB system cannot detect all vehicles
under all conditions.
•The radar sensor does not detect the follow-
ing objects:– Pedestrians or animals
– Oncoming vehicles
– Crossing vehicles
•The radar sensor has some performance
limitations. For stationary vehicles, the FEB
system will not function when the vehicle is
driven at speeds over:
– Approximately 31 MPH (50 km/h) for the
Autonomous braking function.
•The radar sensor may not detect a vehicle
ahead in the following conditions:
– Dirt, ice, snow or other material covering
the radar sensor.
– Interference by other radar sources.
– Snow or heavy rain.
– If the vehicle ahead is narrow (e.g. mo-
torcycle). –
If the vehicle ahead is in a different lane.
– Under strong radar reflections, for ex-
ample, in a multi-level parking garage.
– New vehicle or after a maintenance of the
FEB system. For additional information,
see Break-in schedule later in this sec-
tion
– When driving on a steep downhill slope
or roads with sharp curves.
– When towing a trailer.
•In some road or traffic conditions, the FEB
system may intervene unnecessarily or give
an unnecessary warning. Always pay care-
ful attention to the traffic situation. Do not
rely solely on the distance warning function
and terminate the intervention if necessary.
•Braking distances increase on slippery sur-
faces.
•The system is designed to automatically
check the sensor’s functionality, within cer-
tain limitations. The system may not detect
some forms of obstruction of the sensor
area such as ice, snow, stickers, for ex-
ample. In these cases, the system may not
be able to warn the driver properly. Be sure
that you check, clean and clear the sensor
area regularly.
•Excessive noise will interfere with the warn-
ing chime sound, and the chime may not be
heard.
SYSTEM TEMPORARILY UNAVAILABLE
If the FEB stops working due to a malfunction or
some other reason, one of the following three
messages will be displayed in the vehicle infor-
mation display.
•[Emergency Brake Currently Unavailable See
Operator’s Manual]
•[Emergency Brake Inoperative]
•[Radar Sensors Dirty See Operator’s Manual]
For each of these messages, possible causes
and solutions are listed below.
[Emergency Brake Currently Unavailable See
Operator’s Manual]: The FEB system is tempo-
rarily inoperative. Possible causes:
•The radar sensor system is temporarily inop-
erative, for example, due to electromagnetic
radiation emitted by nearby TV or radio sta-
tions or other sources of electromagnetic
radiation.
•The system is outside the operating tempera-
ture range.
Starting and driving5-65

•The on-board voltage is too low.
Once the causes listed above no longer apply,
the display message goes out. The FEB system
is operative again.
If the display message does not disappear:
•Pull over and stop the vehicle safely as soon
as possible, paying attention to road and
traffic conditions.
•Secure the vehicle against rolling away.
•Switch off the engine.
[Emergency Brake Inoperative]: The FEB system
is temporarily inoperative due to a malfunction.
The adaptive brake assist function may also
have failed.
It is recommended you visit an INFINITI retailer.
[Radar Sensors Dirty See Operator’s Manual]:
The FEB system is temporarily restricted or
inoperative. Possible causes:
•The sensor behind the INFINITI logo is dirty.
•The function of the FEB system is impaired
due to heavy rain or snow. A warning tone also sounds.
Once the causes listed above no longer apply,
the display message goes out. The FEB system
is operative again.
If the display message does not disappear:
•Pull over and stop the vehicle safely as soon
as possible, paying attention to road and
traffic conditions.
•Secure the vehicle against rolling away.
•Switch off the engine.
•Clean the area around the sensors.
•Restart the engine. The display message
disappears.
SYSTEM MAINTENANCE
The sensorAis located behind the INFINITI
logo at the front of the vehicle.
To keep the system operating properly, be sure
to observe the following:
•Always keep the sensor area of the INFINITI
logo clean.
•Do not strike or damage the areas around the
sensor.
•Do not cover or attach stickers or similar
objects on the front bumper near the sensor
area. This could cause failure or malfunction.
•Do not attach metallic objects near the sen-
sor area (brush guard, etc.). This could cause
failure or malfunction.
NSD645
5-66Starting and driving

Wheels and Tiresin the9. Maintenance and
Schedules section.)
– For detailed information, see Wheels and
tires in the 8. Do-it-yourself section.
The Anti-lock Braking System (ABS) controls the
brakes so the wheels do not lock during hard
braking or when braking on slippery surfaces.
The system detects the rotation speed at each
wheel and varies the brake fluid pressure to
prevent each wheel from locking and sliding. By
preventing each wheel from locking, the system
helps the driver maintain steering control and
helps to minimize swerving and spinning on
slippery surfaces.
Using system
Depress the brake pedal and hold it down.
Depress the brake pedal with firm steady pres-
sure, but do not pump the brakes. The ABS will
operate to prevent the wheels from locking up.
Steer the vehicle to avoid obstacles.
WARNING
Do not pump the brake pedal. Doing so may
result in increased stopping distances.
Self-test feature
The ABS includes electronic sensors, electric
pumps, hydraulic solenoids and a computer.
The computer has a built-in diagnostic feature
that tests the system each time you start the
engine and move the vehicle at a low speed in
forward or reverse. When the self-test occurs,
you may hear a “clunk” noise and/or feel a
pulsation in the brake pedal. This is normal and
does not indicate a malfunction. If the computer
senses a malfunction, it switches the ABS off
and illuminates the ABS warning light on the
instrument panel. The brake system then oper-
ates normally, but without anti-lock assistance.
If the ABS warning light illuminates during the
self-test or while driving, have the vehicle
checked. It is recommended you visit an
INFINITI retailer for this service.
Normal operation
The ABS operates at speeds above 3 to 6 MPH
(5 to 10 km/h). The speed varies according to
road conditions.
When the ABS senses that one or more wheels
are close to locking up, the actuator rapidly
applies and releases hydraulic pressure. This
action is similar to pumping the brakes very
quickly. You may feel a pulsation in the brake
pedal and hear a noise from under the hood or
feel a vibration from the actuator when it is
operating. This is normal and indicates that the
ABS is operating properly. However, the pulsa-
tion may indicate that road conditions are haz-
ardous and extra care is required while driving.
Starting and driving5-89

5. Tighten the wheel bolts securely using thewheel wrench in the sequence as illustrated.
6. Lower the vehicle completely.
7. Install the wheel cover (if equipped).
Wheel
bolt tightening torque:96 ft-lb (130 N•m, 13
kg-m)
As soon as possible, tighten the wheel bolts to
the specified torque with a torque wrench.
The wheel bolts must be kept tightened to
specification at all times. It is recommended
that the wheel bolts be tightened to specifica-
tion at each maintenance interval.
Adjust the tire pressure to the COLD pressure.
COLD pressure is the tire pressure as measured
after the vehicle has been parked for three
hours or more or driven for less than 1 mile (1.6
km).
COLD tire pressures are shown on the tire and
loading information label affixed to the driver’s
side center pillar.
Wheel lock bolts (if equipped)
In order to prevent theft, the specially designed
wheel lock bolt is installed to each wheel. The
wheel lock bolt cannot be removed with the
commonly used tools. When removing tires, use the lock key provided
with your vehicle.
Removing the wheel lock bolt
:
1. Insert the wheel lock key1to the wheel
lock bolt.
2. To remove the wheel lock bolt, turn the wheel lock key counterclockwise using the
wheel wrench.
CAUTION
•Do not use a power tool to remove the wheel
lock bolts.
•When installing the wheel, tighten the
wheel lock bolts to the same tightening
torque as the normal wheel bolts. For de-
tails, see Installing the wheel earlier in
this section. NOTE
•The wheel lock bolt has an individual code. A
wheel lock key with other than the individual
code cannot remove the wheel lock bolt. If
you lose the wheel lock key, it is recom-
mended you contact an INFINITI retailer for a
duplicate with the original wheel lock key
code.
•Record the key number and keep it in a safe
place, not in the vehicle.
•When you ask for a service at an INFINITI
retailer, make sure to keep the lock key in
the vehicle. Otherwise, wheels cannot be
removed and the service cannot be per-
formed.
NCE143Z
In case of emergency6-9

8 Do-it-yourself
Maintenance precautions..................8-2
Engine compartment check locations ...........8-3
2.0L Gasoline engine .................. .8-3
Engine cooling system ................... .8-3
Checking engine coolant level .............8-4
Changing engine coolant ................8-4
Engine oil ........................... .8-5
Checking engine oil level ................8-5
Changing engine oil .................. .8-5
Changing engine oil filter ................8-6
Automatic Transmission Fluid (ATF) ............8-7
Brake fluid .......................... .8-7
Window washer fluid .................... .8-8
Battery ............................ .8-9
Accessing Vehicle battery ...............8-10
Maintenance free battery ................8-10
Models with Idle Stop/Start System .........8-10
Battery replacement .................. .8-11
Reinitialisation procedure after battery
reconnection ...................... .8-12
Jump-starting ...................... .8-12
Drive belt .......................... .8-12
Spark plugs ..........................8-13
Air cleaner filter ...................... .8-13
Wiper blades .........................8-13 Cleaning
..........................8-13
Replacing front window wiper blades ........8-14
Replacing rear window wiper blade ..........8-15
Brakes ............................ .8-17
Self-adjusting brakes ..................8-17
Fuses ............................. .8-17
Before replacing a fuse .................8-17
Engine compartment .................. .8-17
Passenger compartment ................8-18
Intelligent key battery replacement ..........
.8-20
Checking the

battery ..................8-20
Replacing the battery ..................8-20
Lights ............................ .8-22
Exterior and interior lights ...............8-22
Replacement procedures ................8-24
Wheels and tires ..................... .8-26
Tire Pressure ...................... .8-26
Tire inflation pressure .................8-28
Tire labeling ...................... .8-28
Types of tires ..................... .8-30
Tire chains ....................... .8-31
Tire wear and damage .................8-31
Tire rotation ...................... .8-32
Replacing wheels and tires ..............8-32
Wheel balance ..................... .8-34

When performing any inspection or mainte-
nance work on your vehicle, always take care to
prevent serious accidental injury to yourself or
damage to the vehicle. The following are gen-
eral precautions which should be closely ob-
served.
WARNING
•Park the vehicle on a level surface, apply the
parking brake securely and block the
wheels to prevent the vehicle from moving.
Press the P (Park) button.
•Be sure the ignition switch is in the OFF
position when performing any parts re-
placement or repairs.
•Do not work under the hood while the en-
gine is hot. Always turn off the engine and
wait until it cools down.
•If you must work with the engine running,
keep your hands, clothing, hair and tools
away from moving fans, belts and any other
moving parts.
•It is advisable to secure or remove any loose
clothing and any jewelry, such as rings,
watches, etc. before working on your ve-
hicle.
•If you must run the engine in an enclosed
space such as a garage, be sure there is
proper ventilation for exhaust gases to es-
cape.
•Never get under the vehicle while it is sup-
ported by a jack.
•Keep smoking materials, flame and sparks
away from fuel and the battery.
•Never connect or disconnect either the bat-
tery or any transistorized component con-
nector while the ignition switch is in the ON
position.
•On gasoline engine models with the Multi-
port Fuel Injection system, the fuel filter and
fuel lines should be serviced by an INFINITI
retailer or qualified workshop because the
fuel lines are under high pressure even
when the engine is turned off.
•Your vehicle is equipped with an automatic
engine cooling fan. It may come on at any
time without warning, even if the ignition
switch is in the OFF position and the engine
is not running. To avoid injury, always dis-
connect the negative battery cable before
working near the fan.
•Always wear eye protection whenever you
work on your vehicle.
•Never leave the engine or the transmission
related component harness connector dis-
connected while the ignition switch is in the
ON position.
•Avoid direct contact with used engine oil
and coolant. Improperly disposed engine
oil, engine coolant, and/or other vehicle flu-
ids can hurt the environment. Always con-
form to local regulations for disposal of ve-
hicle fluids.
This “ 8. Do-it-yourself” section provides in-
structions regarding only those items which are
relatively easy for an owner to perform.
You should be aware that incomplete or im-
proper servicing may result in operating diffi-
culties or excessive emissions, and could affect
your warranty coverage. If in doubt about any
servicing, it is recommended you have it done by
an INFINITI retailer.
MAINTENANCE PRECAUTIONS
8-2Do-it-yourself

1. Park the vehicle on a level surface and applythe parking brake.
2. Start the engine and let it idle until it reaches the normal operating temperature,
then turn it off.
3. Remove the oil filler cap by turning it coun- terclockwise.
4. Remove the engine undershield.
5. Place a large drain pan under the drain plug.
6. Remove the drain plug with a wrench by turning it counterclockwise and completely
drain the oil. If the oil filter is to be changed,
remove and replace it at this time. For
additional information, refer to Changing
engine oil filter later in this section.
•Waste oil must be disposed of properly.
•Check your local regulations.
7. Clean and reinstall the drain plug and a new washer. Securely tighten the drain plug with
a wrench. Do not use excessive force.Drain
plug tightening torque: 22 ft-lb, 30 N•m
8. Refill engine with recommended oil through the oil filler opening, then install the oil filler
cap securely.
For additional information on drain and refill
capacity, refer to Recommended fluids/
lubricants and capacities in the
9. Maintenance and Schedules section.
The drain and refill capacity depends on the
oil temperature and drain time. Use these
specifications for reference only. Always use
the dipstick to determine when the proper
amount of oil is in the engine.
9. Start the engine. Check for leakage around the drain plug and oil filter. Correct as
required.
10. Turn the engine off and wait more than 10 minutes. Check the oil level with the dip-
stick. Add engine oil if necessary.
CHANGING ENGINE OIL FILTER
1. Park the vehicle on a level surface and applythe parking brake.
2. Turn the engine off.
3. Place a large drain pan under the oil filter
1.
4. Loosen the oil filter
1with an oil filter
wrench by turning it counterclockwise. Then
remove the oil filter by turning it by hand.
CAUTION
Be careful not to burn yourself. The engine oil
may be hot.
NDI1622NDI16102.0L gasoline engine
8-6Do-it-yourself