2017 INFINITI QX30 light

CAUTION
Be careful not to allow children to swallow the
battery or removed parts.
CHECKING THE BATTERY
Press the(LOCK) or(UNLOCK)
button.
The battery is working properly if the battery
check lamp
1lights up briefly.
The battery is discharged if the battery check
lamp
1does not light up briefly. Replace the
battery.
NOTE
•If the key battery is checked within the signal
reception range of the vehicle, pressing the
(LOCK) or(UNLOCK) button locks
or unlocks the vehicle.
•You can obtain a battery from an INFINITI
retailer.
REPLACING THE BATTERY
You require a CR 2025 3 V cell battery.
Replace the battery in the Intelligent Key as
follows:
1. Take the emergency key element out of the key (see Mechanical key in the
3. Pre-driving checks and adjustments sec-
tion)
2. Press emergency key element
2into the
opening into the key in the direction of the
arrow until the battery cover
1opens.
When doing so, do not hold cover
1shut.
3. Remove battery tray cover
1.
NPA1474NPA1472
INTELLIGENT KEY BATTERY REPLACEMENT
8-20Do-it-yourself

EXTERIOR AND INTERIOR LIGHTS
ItemWattage (W)
Front combination light Headlight (Low or high beam: H9 type) 14 / 28
Headlight (Low or high beam: LED type, if so equipped) *1 LED
Front turn signal light (with halogen headlights) 24
Front turn signal light (LED type, if so equipped)*1 LED
Front side light *1 LED
Daytime driving light *1 LED
Front fog light *1 LED
Side turn signal light *1 LED
Puddle light *1 LED
Rear combination light Turn signal light*1 LED
Stop/Tail light *1 LED
Reversing light *1 LED
Brake light *1 LED
High-mounted brake light *1 LED
License plate light*1 LED
Room light/Map lights (if so equipped)
Foot well light (if so equipped) 5
3
Reading light (rear)
Room light — rear (if so equipped) 5
5
Reading lights — rear (if so equipped) 8
Luggage compartment light 5
*1: It is recommended you visit an INFINITI retailer for replacement.
It is recommended you check with the Parts Department at an INFINITI retailer for the latest parts
information.1Side turn signal light
2Room light / Map lights (if so equipped)
3Daytime driving light and sidelights and
turn signal (if so equipped)
4Low/High beam headlight
5High beam headlight or turn signal
NDI1625
LIGHTS
8-22Do-it-yourself

6Cornering light (if so equipped)
7Front fog light (if so equipped)
8Daytime driving light and sidelights
9Footwell light (if so equipped)
10Room light (if so equipped)
11High mounted stop light
12License plate light
13Rear Fog and Reversing light
14Brake light
15Turn signal light
16Tail light
Front light unit
Halogen type:
1Turn signal light
2Daytime driving light and sidelight
3High/Low beam halogen projector head-
lights
4Side marker light (if so equipped)
5Reflector (if so equipped)
6Daytime driving light and sidelightsLED type
:
1Cornering light
2Additional high-beam headlight
3Daytime driving light and sidelight and turn
signal light
4High/Low beam LED projector headlights
and Adaptive Front Lighting system (if so
equipped)
5Side marker light (if so equipped)
6Reflector (if so equipped)
7Daytime driving light and sidelights
NDI1613NDI1614
Do-it-yourself8-23

Rear light unit
1Tail light
2Turn signal light
3Brake light
4Tail light
5Reversing light
6Rear fog light (drivers side only)
REPLACEMENT PROCEDURES
LED lights (if so equipped)
The LED headlight is a projector style which
uses a LED module without serviceable parts. If
LED fog headlight , or any other LED light
replacement is required, it is recommended that
you visit an INFINITI retailer for this service.
Halogen headlight bulb
Fitting/removing the access cover on the front
wheel arch:
You must remove the cover of the front wheel
arch before you can change the halogen head-
light bulb.
To remove: switch off the lights, turn the steer-
ing so that the wheel behind the light in
question is pointing inwards . Slide cover
1up
and remove it.
To fit: inset cover
1again and slide it down
until it engages.
The headlight is a semi-sealed beam type which
uses a replaceable headlight (halogen) bulb. A
bulb can be replaced from inside the engine
compartment without removing the headlight
assembly. If you need assistance for bulb replacement, it
is recommended that you visit an INFINITI re-
tailer.
NDI1615NDI1626
8-24Do-it-yourself

Low/High beam Headlight bulb replacement:
1. Open the hood. For details, seeHoodin the
3. Pre-driving checks and adjustments sec-
tion.
2. Disconnect the negative (—) battery cable.
3. Remove the corresponding access cover from the wheel arch.
4. Turn housing cover
1counterclockwise and
remove it.
5. Turn bulb holder
2counterclockwise and
pull out
6. Take the headlight bulb out of bulb holder
2.
7. Insert the new bulb into bulb holder
2.
8. Insert bulb holder
2and turn it clockwise. 9. Press on housing cover
1and turn it to the
right.
10. Replace the cover in the front wheel arch
11. Reconnect the negative (—) battery cable and close the hood.
NOTE
Fog may temporarily form inside the lens of the
exterior lights in the rain or in a car wash. The
fog is caused by a temperature difference be-
tween the inside and the outside of the lens. This
is not a malfunction. If large droplets can be
seen, it is recommended that you visit an
INFINITI retailer.
Front turn signal light bulb
replacement (non-LED system only)
1. Open the hood. For details, see Hoodin the
3. Pre-driving checks and adjustments sec-
tion.
2. Disconnect the negative (—) battery cable.
3. Turn housing cover
1counterclockwise and
remove it.
4. Turn bulb holder
2counterclockwise and
pull out
5. Take the headlight bulb out of bulb holder
2.
6. Insert the new bulb into bulb holder
2.
7. Insert bulb holder
2and turn it clockwise.
NDI1611NDI1612
Do-it-yourself8-25

8. Press on housing cover1and turn it to the
right.
9. Reconnect the negative (—) battery cable and close the hood. If you have a flat tire, refer to
Flat tirein the6.
In case of emergency section.
TIRE PRESSURE
Tire Pressure Monitoring System
(TPMS)
The Tire Pressure Monitoring System (TPMS)
monitors tire pressure of all tires. When the low
tire pressure warning light is lit, one or more of
the tires is significantly under-inflated.
The TPMS will activate only when the vehicle is
driven at speeds above 16 MPH (25 km/h). Also,
this system may not detect a sudden drop in tire
pressure (for example a flat tire while driving).
For additional information, refer to Tire Pres-
sure Monitoring System (TPMS) in the
5. Starting and driving section.
Tire inflation pressure
Check the tire pressures (including the spare)
often and always prior to long distance trips.
The recommended tire pressure specifications
are shown on the F.M.V.S.S./C.M.V.S.S. label or
the Tire and Loading Information label (if so
equipped) under the Cold Tire Pressure head-
ing. The Tire and Loading Information label is
affixed to the driver side center pillar. Tire pressures should be checked regularly be-
cause:
•Most tires naturally lose air over time.
•Tires can lose air suddenly when driven over
potholes or other objects or if the vehicle
strikes a curb while parking.
The tire pressures should be checked when the
tires are cold. The tires are considered COLD
after the vehicle has been parked for 3 or more
hours, or driven less than 1 mile (1.6 km) at
moderate speeds.
WARNING
•Improperly inflated tires can fail suddenly
and cause an accident.
•The Gross Vehicle Weight rating (GVWR) is
located on the F.M.V.S. S./C.M.V.S.S. certi-
fication label. The vehicle weight capacity is
indicated on the Tire and Loading Informa-
tion label (if so equipped). Do not load your
vehicle beyond this capacity. Overloading
your vehicle may result in reduced tire life,
unsafe operating conditions due to prema-
ture tire failure, or unfavorable handling
characteristics and could also lead to a se-
rious accident. Loading beyond the speci-
fied capacity may also result in failure of
other vehicle components.
WHEELS AND TIRES
8-26Do-it-yourself

Confirm the following for the TPMS:
WARNING
•The use of tires other than those recom-
mended or the mixed use of tires of different
brands, construction (bias, bias-belted or
radial), or tread patterns can adversely af-
fect the ride, braking, handling, VDC sys-
tem, ground clearance, body-to-tire clear-
ance, tire chain clearance, speedometer
calibration, headlight aim and bumper
height. Some of these effects may lead to
accidents and could result in serious per-
sonal injury.
•For 2WD models, if your vehicle was origi-
nally equipped with 4 tires that were the
same size and you are only replacing 2 of
the 4 tires, install the new tires on the rear
axle. Placing new tires on the front axle may
cause loss of vehicle control in some driving
conditions and cause an accident and per-
sonal injury.
•If the wheels are changed for any reason,
always replace with wheels which have the
same off-set dimension. Wheels of a differ-
ent off-set could cause premature tire wear,
degrade vehicle handling characteristics,
affect the VDC system and/or interference
with the brake discs. Such interference canlead to decreased braking efficiency and/or
early brake pad wear. For additional infor-
mation on wheel off-set dimensions, refer to
Wheels and Tires
in the9. Maintenance
and Schedules section.
•When a replacement tire is mounted or a
wheel is replaced, the TPMS will not func-
tion and the low tire pressure warning light
will flash for approximately 1 minute. The
light will remain on after 1 minute. Contact
an INFINITI retailer as soon as possible for
tire replacement and/or system resetting.
•Replacing tires with those not originally
specified by INFINITI could affect the proper
operation of the TPMS.
•The TPMS sensor may be damaged if it is not
handled correctly. Be careful when handling
the TPMS sensor.
•When replacing the TPMS sensor, the ID
registration may be required. It is recom-
mended that you visit an INFINITI retailer for
ID registration.
•Do not use a valve stem cap that is not speci-
fied by INFINITI. The valve stem cap may
become stuck.
•Be sure that the valve stem caps are cor-
rectly fitted. Otherwise the valve may be clogged up with dirt and cause a malfunc-
tion or loss of pressure.
•Do not install a damaged or deformed wheel
or tire even if it has been repaired. Such
wheels or tires could have structural dam-
age and could fail without warning.
•The use of retread tires is not recom-
mended.
•For additional information regarding tires,
refer to
Important Tire Safety Information
(US) or Tire Safety Information (Canada) in
the Warranty Information Booklet.
Care of wheels
•Wash the wheels when washing the vehicle
to maintain their appearance.
•Clean the inner side of the wheels when the
wheel is changed or the underside of the
vehicle is washed.
•Do not use abrasive cleaners when washing
the wheels.
•Inspect wheel rims regularly for dents or
corrosion. Such damage may cause loss of
pressure or poor seal at the tire bead.
Do-it-yourself8-33

released. When driving in areas using road salt
or other corrosive materials, check lubrication
frequently.
Lights*
:
Clean the headlights on a regular basis. Make
sure that the headlights, stop lights, tail lights,
turn signal lights, and other lights are all oper-
ating properly and installed securely. Also
check the aim of the headlights.
Road wheel nuts (lug nuts)*
:
When checking the tires, make sure no wheel
nuts are missing, and check for any loose wheel
nuts. Tighten if necessary.
Tire rotation*
:
Tires should be rotated every 5,000 miles
(8,000 km). Tires marked with directional indi-
cators can only be rotated between front and
rear. Make sure that the directional indicators
point in the direction of wheel rotation after the
tire rotation is completed.
Tires*
:
Check the pressure with a gauge often and
always prior to long distance trips. Adjust the
pressure in all tires to the pressure specified.
Check carefully for damage, cuts or excessive
wear.Tire Pressure Monitoring System (TPMS) trans-
mitter components
:
Replace the TPMS transmitter grommet seal,
valve core and cap when the tires are replaced
due to wear or age.
Wheel alignment and balance
:
If the vehicle should pull to either side while
driving on a straight and level road, or if you
detect uneven or abnormal tire wear, there may
be a need for wheel alignment.
If the steering wheel or seat vibrates at normal
highway speeds, wheel balancing may be
needed.
For additional information regarding tires, refer
to “Important Tire Safety Information” (US) or
“Tire Safety Information” (Canada) in the
INFINITI Warranty Information Booklet.
Windshield
:
Clean the windshield on a regular basis. Check
the windshield at least every six months for
cracks or other damage. Have a damaged wind-
shield repaired by a qualified repair facility.
Wiper blades*
:
Check for cracks or wear if not functioning
correctly. Replace as necessary.
Inside the vehicle
The maintenance items listed here should be
checked on a regular basis, such as when
performing scheduled maintenance, cleaning
the vehicle, etc.
Accelerator pedal
:
Check the pedal for smooth operation and make
sure that the pedal does not catch or require
uneven effort. Keep the floor mat away from the
pedal.
Automatic transmission P (Park) mechanism
:
On a fairly steep hill, check that your vehicle is
held securely when P (Park) has been activated,
without applying any brakes.
Brake pedal*
:
Check the pedal for smooth operation. If the
brake pedal suddenly goes down further than
normal, the pedal feels spongy or the vehicle
seems to take longer to stop, have your vehicle
checked immediately. It is recommended you
visit an INFINITI retailer for this service. Keep
the floor mat away from the pedal.
Brakes
:
Check that the brakes do not pull the vehicle to
one side when applied.
Maintenance and Schedules9-3