2017 INFINITI QX30 reset

Press and hold thebutton until the side
windows are in the desired position.
To interrupt convenience opening: release the
button.
Convenience closing feature
WARNING
When the convenience closing feature is oper-
ating, parts of the body could become trapped
in the closing area of the side window. There is
a risk of injury. Observe the complete closing
procedure when the convenience closing fea-
ture is operating. When closing make sure that
no parts of the body are in the closing area.
For vehicles with Intelligent key: The key can
also be used to carry out the following functions
simultaneously:
•Lock the vehicle
•Close the side windows The driver’s door and the door at which the
handle is used must both be closed. The key
must be outside the vehicle. The gap between
the key and the corresponding door handle
should not be greater than 1 m.
Press and hold the
button until the side
windows are fully closed.
To interrupt convenience closing: release the
button.
You can also use the keyless locking feature to
activate convenience closing: Touch recessed sensor surface
1on the door
handle until the side windows are fully closed.
NOTE
Make sure you only touch recessed sensor sur-
face
1.
To interrupt convenience opening: release the
recessed sensor surface
1on the door handle.
Resetting the side windows
If a side window can no longer be closed fully,
you must reset it.
1. Switch the ignition switch to the ON position.
2. Close the door.
3. Pull the corresponding switch on the door control panel until the side window is com-
pletely closed
NPA1478
2-74Instruments and controls

4. Hold the switch for an additional second.
If the side window opens again slightly:
1. Immediately pull the corresponding switchon the door control panel until the side
window is completely closed.
2. Hold the switch for an additional second.
3. If the corresponding side window remains closed after the button has been released,
the side window has been reset correctly. If
this is not the case, repeat the steps above
again.
If the power window automatic function does
not operate properly after performing the pro-
cedure above, have your vehicle checked. It is
recommended you visit an INFINITI retailer for
this service.
1Close
2Open
CAUTION
•Do not place heavy objects on the glass roof
or surrounding area.
•Do not hang from the sunshade or hang any
objects from it. It may cause damage or de-
formation to the sunshade.
•Close the sunshade when you leave the ve-
hicle for extended periods of time to prevent
the inside of the vehicle from reaching high
temperatures.
SUNSHADE OPERATION
The sunshade operates only when the ignition
switch is in the ON position.
WARNING
To avoid personal injury, keep your hands, fin-
gers and head away from the sunshade arm,
the arm rail and sunshade inlet port.
NOTE
The following notes cover situations where
strong sun shining on the roof of the vehicle
causes the area around the sunshade motor to
reach high temperatures:
•If the temperature of the sunshade motor
reaches a value between 185oF (85oC) and
212oF (100oC), “restricted mode” is enabled,
and the sunshade will only be allowed to
CLOSE.
•If the temperature of the sunshade motor
exceeds 212oF (100oC), the sunshade will
not operate.
NIC2646
FIXED GLASS ROOF (IF EQUIPPED)
Instruments and controls2-75

If the [Fold Mirrors in when Locking] option has
been activated in the Vehicle information dis-
play:
•The exterior mirrors fold in automatically as
soon as you lock the vehicle from the out-
side.
•The exterior mirrors fold out again automati-
cally as soon as you unlock the vehicle and
then open the driver’s or front-passenger
door.
Automatic parking positioner (if so
equipped)
The Parking position for the exterior mirror on
the front-passenger side function is only avail-
able if the vehicle is equipped with the Memory
package.
1Button for the exterior mirror on the left
hand side.
2Button for the exterior mirror on the right
hand side.
3Adjustment button.
4Memory button M.Setting and storing the parking position using
reverse gear
:
You can set the front-passenger side exterior
mirror so that you can see the rear wheel on
that side as soon as you engage reverse gear.
You can store this position.
1. Make sure that the vehicle is stationary.
2. Switch the ignition switch to the ON posi-
tion.
3. Press button
2for the external mirror on
the front-passenger side.
4. Engage reverse gear. The exterior mirror on the front-passenger side moves to the preset
parking position.
5. Use adjustment button
3to adjust the
exterior mirror. You should see the rear
wheel and the curb in the exterior mirror The
parking position is stored.
NOTE
•If you shift the transmission to another po-
sition, the exterior mirror on the front pas-
senger side returns to the driving position.
•If the driver’s side mirror is currently se-
lected, the passenger side mirror will not
move when reverse gear is engaged.
NIC2639
Pre-driving checks and adjustments3-19

Setting and storing the parking position using
the memory button:
You can set the front-passenger side exterior
mirror so that you can see the rear wheel on
that side as soon as you engage reverse gear.
This setting can be stored using memory button
M
4.
1. Make sure that the vehicle is stationary.
2. Switch the ignition switch to the ON posi- tion.
3. Press button
2for the external mirror on
the front-passenger side.
4. Engage reverse gear. The exterior mirror on the front-passenger side moves to the preset
parking position.
5. Use adjustment button
3to adjust the
exterior mirror. You should see the rear
wheel and the curb in the exterior mirror.
6. Press memory button M
4and one of the
arrows on adjustment button
3within
three seconds. The parking position is
stored if the exterior mirror does not move.
7. If the mirror moves out of position, repeat the steps. Calling up a stored parking position
:
1. Switch the ignition switch to the ON position.
2. Adjust the exterior mirror on the front pas-
senger side with the corresponding button.
3. Engage reverse gear. The exterior mirror on the front-passenger side moves to the stored
parking position
The exterior mirror on the front-passenger side
moves back to its original position:
•As soon as you exceed a speed of 15 km/h.
•About ten seconds after you have disen-
gaged reverse gear.
•If you press button1for the exterior mirror
on the driver’s side.
WARNING
•If you use the memory function on the driv-
er’s side while driving, the adjustments
could cause you to lose control of the ve-
hicle. There is a risk of an accident. Only use
the memory function on the driver’s side
while the vehicle is stationary.
Only use the memory function on the driv-
er’s side while the vehicle is stationary.
•If the memory function adjusts the seat, you
and other vehicle occupants-particularly
children-could become trapped. There is a
risk of injury.
While the memory function is making ad-
justments, make sure that no one has any
part of their body within the sweep of the
NIC2637
MEMORY FUNCTION (IF EQUIPPED)
3-20Pre-driving checks and adjustments

seat. If someone becomes trapped, immedi-
ately release the memory function position
button The adjustment is stopped.
•If children activate the memory function,
they could become trapped, especially if
they are unattended. There is a risk of in-
jury.
When leaving the vehicle, always take the
key with you and lock the vehicle. Never
leave children unattended in the vehicle.
The memory function can be used at any time,
e.g. even when the key isn’t in the ignition lock.
STORING SETTINGS
With the memory function, you can store up to
three different settings.
•Seat and seatback position
•Driver’s side: position of the exterior mirrors
on the driver’s and front-passenger sides.
To store settings:
1. Adjust the seat (see Power seat adjustment
in the 1. Safety — seats, seat belts and
supplemental restraint system section).
2. Adjust the exterior mirror on the driver’s side (see Adjusting in the3. Pre-driving checks
and adjustments section).
3. Briefly press the M memory button
1, and
then press preset position button 1, 2 or 3
2within three seconds.
The settings are stored in the selected pre-
set position. A tone sounds when the set-
tings have been completed.
CALLING UP A STORED SETTING
Press and hold the relevant preset position
button 1, 2 or 3 until the seat and exterior
mirrors are in the stored position.
NOTE
The setting procedure is interrupted as soon as
you release the storage position button.
Pre-driving checks and adjustments3-21

ITEMS TO BE SET INITIALLY
The initial setting operations included in this
section should be performed before using the
system for the first time.
Screen settings
The display can be turned on/off and the image
quality of the display can be adjusted in this
menu.
1. Push

ADDITIONAL SYSTEM INFORMATION
System Start-Up
Due to the large number of features and capa-
bilities that the INFINITI InTouch system needs
to load on start-up, it may take up to a minute
for all functions (such as Apps) to be available.
The system will display the message indicating
that the application is loading during this time.
During the start-up period, hard button controls
for audio will become available before start-up
is complete. Features will become available in
the following order.
•Audio volume and music playback
•Audio Full Screen Access
•Full App Availability – System will display the
message indicating the completion of the
application loading process.
System Response Delay
INFINITI InTouch uses an operating system like
those found on many computers, tablets and
cell phones. Like these devices, processing
speed may vary, and system response delays or
resets may occur intermittently. This does not
indicate a malfunction, and further information
on system operation can be found below. In most situations, simply waiting a few mo-
ments longer should be sufficient for the pend-
ing operations to complete.
If the system temporarily does not respond to
commands, the system can be easily reset.
Simply push down the Audio Power knob for at
least 5 seconds. The system will turn off and
restart.
After restart, all functions should be available.
•Audio will resume, but if you were using
Bluetooth® Audio or an Audio App, the
connection may need to be re-established.
•If a navigation route was set, the route
should resume automatically (models with
navigation system).
•If a phone call was in progress, the call may
be temporarily transferred back to the hand-
set.
System Reset
As noted above, intermittent system resets may
occur during normal operation. You may also
wish to reset the system if you find that a
particular feature is not loading or responding.
Often, a quick system reset will resolve any
issue you may be experiencing. After restart, all
functions will be available as described above. System Updates
Like many digital devices, the INFINITI InTouch
system is designed to allow for software up-
dates as enhancements are developed and ad-
ditional features added. If you have questions
about system performance, it is recommended
you contact your INFINITI retailer to ensure that
your vehicle has had the latest available soft-
ware installed.
Operating Tips
INFINITI InTouch provides several methods of
operation to suit your preferences. The follow-
ing are suggested operating tips.
•Operating the INFINITI Controller, Steering
Wheel Controls, or other controls too quickly
can cause a lag between the control and the
display. Operate the controls carefully and
allow the system to respond to your request.
•INFINITI recommends using Voice Recogni-
tion whenever possible to select options
while driving. Some touch screen functional-
ity is intentionally unavailable during driving.
Please view the available voice commands by
pushing
<
>on the steering wheel and
then selecting a category on the display.
•In some situations, the system may not be
able to recognize your command even if you
Display screen, heater and air conditioner, and audio system4-15

3. Slowly back up the vehicle adjusting thesteering wheel so that the predicted course
lines
Benter the parking spaceC. 4. When the rear of the vehicle enters the
parking space
C, maneuver the steering
wheel to make the vehicle width guide lines
Dparallel to the parking spaceC.
5. When the vehicle is parked in the space completely, press the P (Park) button and
apply the parking brake.
ADJUSTING THE SCREEN
1. While the RearView Monitor is displayed,touch the settings icon.
2. Select the item you wish to adjust:
[Brightness]:
Adjust display settings by touching [+]/[-].
[Contrast]:
Adjust display settings by touching [+]/[-].
[Black level]:
Adjust display settings by touching [+]/[-].
[Tint]:
Adjust display settings by touching [+]/[-].
[Color]:
Adjust display settings by touching [+]/[-]. [Reset Settings]:
Return all the settings to default
NOTE
Do not adjust any of the display settings of the
RearView Monitor while the vehicle is moving.
Make sure the parking brake is firmly applied.
SAA1898
Display screen, heater and air conditioner, and audio system4-21