2017 INFINITI QX30 wheel

For additional traction on icy roads, studded
tires may be used. However, some U.S. states
and Canadian provinces prohibit their use.
Check local, state and provincial laws before
installing studded tires. Skid and traction capa-
bilities of studded snow tires on wet or dry
surfaces may be poorer than that of non-
studded snow tires.
Four-Wheel Drive (4WD) models
If excessive tire wear is found, it is recom-
mended that all four tires be replaced with tires
of the same size, brand, construction and tread
pattern. The tire pressure and wheel alignment
should also be checked and corrected as nec-
essary. It is recommended that you visit an
INFINITI retailer.
TIRE CHAINS
CAUTION
Tire chains/cables should not be installed on
235/45 R19 or 235/50 R18 size tires. Installa-
tion of the tire chains/cables on 235/45 R19 or
235/50 R18 size tires will cause damage to the
vehicle. If you plan to use tire chains/cables,
you should install 215/60 R17 size tires on your
vehicle.Use of tire chains may be prohibited according
to location. Check the local laws before install-
ing tire chains. When installing tire chains,
make sure that they are of proper size for the
tires on your vehicle and are installed according
to the chain manufacturer’s instructions.
Use chain tensioners when recommended by
the tire chain manufacturer to ensure a tight fit.
Loose end links of the tire chains must be
secured or removed to prevent the possibility of
whipping action damage to the fenders or un-
derbody. If possible, avoid fully loading your
vehicle when using tire chains. In addition,
drive at a reduced speed. Otherwise, your ve-
hicle may be damaged and/or vehicle handling
and performance may be adversely affected.
Tire chains must be installed only on the front
wheels and not on the rear wheels.
Never install tire chains on a T-type spare tire
(TEMPORARY USE ONLY).
Do not drive with tire chains on paved roads
which are clear of snow. Driving with chains in
such conditions can cause damage to the vari-
ous mechanisms of the vehicle due to some
overstress.
1: Wear indicator
2: Location mark
TIRE WEAR AND DAMAGE
WARNING
•Tires should be periodically inspected for
wear, cracking, bulging or objects caught in
the tread. If excessive wear, cracks, bulging
or deep cuts are found, the tire should be
replaced immediately.
•The original tires have a built-in tread wear
indicator. When the wear indicator is vis-
ible, the tire should be replaced.
•Tires degrade with age and use. Have tires,
including the spare, over 6 years old
checked by a qualified technician because
SDI1663Z
Do-it-yourself8-31

some tire damage may not be obvious. Re-
place the tires as necessary to prevent tire
failure and possible personal injury.
•Improper service of the spare tire may result
in serious personal injury. If it is necessary
to repair the spare tire, it is recommended
that you visit an INFINITI retailer for this
service.
•For additional information regarding tires,
refer to “Important Tire Safety Information”
(US) or “Tire Safety Information” (Canada)
in the Warranty Information Booklet.
Tires should be periodically inspected for wear,
cracking, bulging or objects caught in the tread.
If excessive wear, cracks, bulging or deep cuts
are found, the tire should be replaced immedi-
ately.
The original tires have a built-in tread wear
indicator. When the wear indicator is visible,
the tire should be replaced.
Improper servicing of a tire may result in seri-
ous personal injury. If it is necessary to repair a
tire, it is recommended you contact an INFINITI
retailer.
TIRE ROTATION
INFINITI recommends rotating the tires every
5,000 miles (8,000 km).
For additional information on tire replacing
procedures, refer to Flat tirein the6. In case
of emergency section.As soon as possible,
tighten the wheel nuts to the specified torque
with a torque wrench.
Wheel nut tightening torque: 96 ft-lb (130 N·m)
The wheel nuts must be kept tightened to speci-
fications at all times. It is recommended that
wheel nuts be tightened to specification at each
tire rotation interval.
WARNING
•After rotating the tires, check and adjust the
tire pressure.
•Do not include the spare tire in the tire rota-
tion.
•For additional information regarding tires,
refer to Important Tire Safety Information
(US) or Tire Safety Information in the War-
ranty Information Booklet.
REPLACING WHEELS AND TIRES
WARNING
Do not install a deformed wheel or tire even if it
has been repaired. Such wheels or tires could
have structural damage and could fail without
warning.
When replacing a tire, use the same size, speed
rating and load carrying capacity as originally
equipped. (See Wheels and Tires in the
9. Maintenance and Schedules section for
recommended types and sizes of tires and
wheels.)
If the wheels are changed for any reason,
always replace with wheels which have the
same offset dimension. Wheels of a different
offset could cause early tire wear, possibly
degraded vehicle handling characteristics
and/or interference with the brake discs/
drums. Such interference can lead to decreased
braking efficiency and/or early brake pad/shoe
wear.
8-32Do-it-yourself

Confirm the following for the TPMS:
WARNING
•The use of tires other than those recom-
mended or the mixed use of tires of different
brands, construction (bias, bias-belted or
radial), or tread patterns can adversely af-
fect the ride, braking, handling, VDC sys-
tem, ground clearance, body-to-tire clear-
ance, tire chain clearance, speedometer
calibration, headlight aim and bumper
height. Some of these effects may lead to
accidents and could result in serious per-
sonal injury.
•For 2WD models, if your vehicle was origi-
nally equipped with 4 tires that were the
same size and you are only replacing 2 of
the 4 tires, install the new tires on the rear
axle. Placing new tires on the front axle may
cause loss of vehicle control in some driving
conditions and cause an accident and per-
sonal injury.
•If the wheels are changed for any reason,
always replace with wheels which have the
same off-set dimension. Wheels of a differ-
ent off-set could cause premature tire wear,
degrade vehicle handling characteristics,
affect the VDC system and/or interference
with the brake discs. Such interference canlead to decreased braking efficiency and/or
early brake pad wear. For additional infor-
mation on wheel off-set dimensions, refer to
Wheels and Tires
in the9. Maintenance
and Schedules section.
•When a replacement tire is mounted or a
wheel is replaced, the TPMS will not func-
tion and the low tire pressure warning light
will flash for approximately 1 minute. The
light will remain on after 1 minute. Contact
an INFINITI retailer as soon as possible for
tire replacement and/or system resetting.
•Replacing tires with those not originally
specified by INFINITI could affect the proper
operation of the TPMS.
•The TPMS sensor may be damaged if it is not
handled correctly. Be careful when handling
the TPMS sensor.
•When replacing the TPMS sensor, the ID
registration may be required. It is recom-
mended that you visit an INFINITI retailer for
ID registration.
•Do not use a valve stem cap that is not speci-
fied by INFINITI. The valve stem cap may
become stuck.
•Be sure that the valve stem caps are cor-
rectly fitted. Otherwise the valve may be clogged up with dirt and cause a malfunc-
tion or loss of pressure.
•Do not install a damaged or deformed wheel
or tire even if it has been repaired. Such
wheels or tires could have structural dam-
age and could fail without warning.
•The use of retread tires is not recom-
mended.
•For additional information regarding tires,
refer to
Important Tire Safety Information
(US) or Tire Safety Information (Canada) in
the Warranty Information Booklet.
Care of wheels
•Wash the wheels when washing the vehicle
to maintain their appearance.
•Clean the inner side of the wheels when the
wheel is changed or the underside of the
vehicle is washed.
•Do not use abrasive cleaners when washing
the wheels.
•Inspect wheel rims regularly for dents or
corrosion. Such damage may cause loss of
pressure or poor seal at the tire bead.
Do-it-yourself8-33

•INFINITI recommends waxing the road wheels
to protect against road salt in areas where it
is used during winter.
WHEEL BALANCE
Unbalanced wheels may affect vehicle handling
and tire life. Even with regular use, wheels can
get out of balance. Therefore, they should be
balanced as required.
Wheel balance service should be performed
with the wheels off the vehicle. Spin balancing
the wheels on the vehicle could lead to me-
chanical damage.
For additional information regarding tires, refer
toImportant Tire Safety Information (US) or
Tire Safety Information (Canada) in the War-
ranty Information Booklet.
8-34Do-it-yourself

released. When driving in areas using road salt
or other corrosive materials, check lubrication
frequently.
Lights*
:
Clean the headlights on a regular basis. Make
sure that the headlights, stop lights, tail lights,
turn signal lights, and other lights are all oper-
ating properly and installed securely. Also
check the aim of the headlights.
Road wheel nuts (lug nuts)*
:
When checking the tires, make sure no wheel
nuts are missing, and check for any loose wheel
nuts. Tighten if necessary.
Tire rotation*
:
Tires should be rotated every 5,000 miles
(8,000 km). Tires marked with directional indi-
cators can only be rotated between front and
rear. Make sure that the directional indicators
point in the direction of wheel rotation after the
tire rotation is completed.
Tires*
:
Check the pressure with a gauge often and
always prior to long distance trips. Adjust the
pressure in all tires to the pressure specified.
Check carefully for damage, cuts or excessive
wear.Tire Pressure Monitoring System (TPMS) trans-
mitter components
:
Replace the TPMS transmitter grommet seal,
valve core and cap when the tires are replaced
due to wear or age.
Wheel alignment and balance
:
If the vehicle should pull to either side while
driving on a straight and level road, or if you
detect uneven or abnormal tire wear, there may
be a need for wheel alignment.
If the steering wheel or seat vibrates at normal
highway speeds, wheel balancing may be
needed.
For additional information regarding tires, refer
to “Important Tire Safety Information” (US) or
“Tire Safety Information” (Canada) in the
INFINITI Warranty Information Booklet.
Windshield
:
Clean the windshield on a regular basis. Check
the windshield at least every six months for
cracks or other damage. Have a damaged wind-
shield repaired by a qualified repair facility.
Wiper blades*
:
Check for cracks or wear if not functioning
correctly. Replace as necessary.
Inside the vehicle
The maintenance items listed here should be
checked on a regular basis, such as when
performing scheduled maintenance, cleaning
the vehicle, etc.
Accelerator pedal
:
Check the pedal for smooth operation and make
sure that the pedal does not catch or require
uneven effort. Keep the floor mat away from the
pedal.
Automatic transmission P (Park) mechanism
:
On a fairly steep hill, check that your vehicle is
held securely when P (Park) has been activated,
without applying any brakes.
Brake pedal*
:
Check the pedal for smooth operation. If the
brake pedal suddenly goes down further than
normal, the pedal feels spongy or the vehicle
seems to take longer to stop, have your vehicle
checked immediately. It is recommended you
visit an INFINITI retailer for this service. Keep
the floor mat away from the pedal.
Brakes
:
Check that the brakes do not pull the vehicle to
one side when applied.
Maintenance and Schedules9-3

Parking brake*:
Check the parking brake operation regularly.
Also make sure that the vehicle is held securely
on a fairly steep hill when only the parking
brake is applied. If the parking brake needs
adjustment, it is recommended you visit an
INFINITI retailer for this service.
Seats
:
Check seat position controls such as seat ad-
justers, seatback recliner, etc. to ensure they
operate smoothly and that all latches lock
securely in every position. Check that the head
restraints move up and down smoothly and that
the locks (if so equipped) hold securely in all
latched positions.
Seat belts
:
Check that all parts of the seat belt system (for
example, buckles, anchors, adjusters and re-
tractors) operate properly and smoothly, and
are installed securely. Check the belt webbing
for cuts, fraying, wear or damage.
Steering wheel
:
Check for changes in the steering condition,
such as excessive free play, hard steering or
strange noises.Warning lights and chimes
:
Make sure that all warning lights and chimes
are operating properly.
Windshield defroster
:
Check that the air comes out of the defroster
outlets properly and in good quantity when
operating the heater or air conditioner.
Windshield wiper and washer*
:
Check that the wipers and washer operate
properly and that the wipers do not streak.
Under the hood and vehicle
The maintenance items listed here should be
checked periodically (for example, each time
you check the engine oil or refuel).
Battery*
:
Except for maintenance free battery, check the
fluid level in each cell. It should be between the
“UPPER” and “LOWER” lines. Vehicles operated
in high temperatures or under severe condi-
tions require frequent checks of the battery
fluid level.
NOTE
Care should be taken to avoid situations that can
lead to potential battery discharge and potential
no-start conditions such as:
1. Installation or extended use of electronic ac-
cessories that consume battery power when
the engine is not running (Phone chargers,
GPS, DVD players, etc.)
2. Vehicle is not driven regularly and/or only driven short distances.
In these cases, the battery may need to be
charged to maintain battery health.
Brake fluid level*
:
Make sure that the brake fluid level is between
the “MAX” and “MIN” lines on the reservoir.
Coolant level*
:
Check the coolant level when the engine is cold.
Engine drive belt(s)*
:
Make sure that no belt is frayed, worn, cracked
or oily.
Engine oil level*
:
Check the level after parking the vehicle on a
level spot and turning off the engine. Wait more
than 15 minutes for the oil to drain back into the
oil pan.
9-4Maintenance and Schedules

The vehicle information display shows a service
message for a few seconds, e g:
•[Service A In .. days]
•[Service A Due]
•[Service A Exceeded by .. days]
Depending on the operating conditions of the
vehicle, the remaining time or distance until the
next service due date is displayed.
The letter indicates which service is due. A
stands for a minor service and B for a major
service. A number or another letter may be
displayed after the letter.
Only for certain countries: the position after the
letter A or B indicates any necessary additional
maintenance work. If you notify an INFINITI
retailer of this display, you will receive a state-
ment on the associated costs.
The maintenance service interval display does
not take into account any periods of time during
which the battery is disconnected.
Maintaining the time-dependent service sched-
ule:
Note down the service due date displayed in the
vehicle information display before disconnect-
ing the battery.
or After reconnecting the battery, subtract the
battery disconnection periods from the service
date shown on the display.
Hiding service messages
Press the orbutton on the steering
wheel.
Displaying service messages
1. Switch the ignition on.
2. Press the
orbutton on the
steering wheel to select the [Serv.] menu.
3. Press the
orbutton to select
[Maintenance] submenu and confirm by
pressing the OK button.
The service due date appears in the vehicle
information display.
Information about service
Resetting the maintenance service interval display:
CAUTION
If the maintenance service interval display has
been inadvertently reset, this setting can be
corrected at an INFINITI retailer.
Have service work carried out as described in
the Maintenance Schedule. This may other-
wise lead to increased wear and damage to the
major assemblies or the vehicle. An INFINITI retailer will reset the maintenance
service interval display after the service work
has been carried out. You can also obtain
further information on maintenance work, for
example.
Special service requirements
:
The prescribed service interval is based on
normal operation of the vehicle. Service work
will need to be performed more often if the
vehicle is operated under arduous conditions or
increased loads, for example:
•Regular city driving with frequent intermedi-
ate stops
•If the vehicle is primarily used to travel short
distance
•For frequent operation in mountainous ter-
rain or on poor road surfaces
•If the engine is often left idling for long
periods
In these or similar operating conditions, have,
for example, the air filter, engine oil and oil
filter changed more frequently. The tires must
be checked more frequently if the vehicle is
operated under increased loads. Further infor-
mation can be obtained at an INFINITI retailer.
9-8Maintenance and Schedules

10 Technical information
Recommended fluids/lubricants and capacities . . . .10-2Fuel recommendation ..................10-3
Engine oil and oil filter recommendations ......10-5
Air conditioner system refrigerant and oil
recommendations ................... .10-6
Engine specifications ................... .10-7
Wheels and Tires ..................... .10-8
Dimensions ..........................10-8
When traveling or registering in another country . . .10-9
Vehicle identification ................... .10-9
Vehicle identification number (VIN) plate ......10-9
Vehicle identification number (chassis number) .10-10
Engine serial number .................10-10
F.M.V.S.S./C.M.V.S.S. Certification label ......10-10
Emission control information label ..........10-11
Tire and loading information label ..........10-11
Air conditioner specification label ..........10-11Installing front license plate
...............10-12
Vehicle loading information ................10-13
TERMS ..........................10-13
Vehicle load capacity .................10-14
Loading tips ...................... .10-15
Measurement of weights ...............10-15
Trailer towing ....................... .10-15
Uniform tire quality grading ...............10-16
Treadwear ....................... .10-16
Traction AA, A, B and C ................10-16
Temperature A, B and C ................10-16
Emission control system warranty ............10-17
Reporting safety defects ..................10-17
Readiness for inspection/maintenance (I/M) test . . .10-18
Event data recorders (EDR) (if so equipped) ......10-19
Owner’s manual/service manual order information . .10-19