2017 INFINITI QX30 wheel

Removing the wheel
WARNING
•The jack must be placed on firm level
ground. Failure to observe this instruction
could result in vehicle damage, or serious
injury or death.
•Make sure to read the caution label at-
tached to the jack body before use.
•DO NOT GET UNDER A VEHICLE THAT IS SUP-
PORTED BY A JACK.
•Never use a jack which was not designed for
your vehicle.
•Use the correct jacking points. Never use
any other part of the vehicle for jack sup-
port.
•Never lift the vehicle more than necessary.
•Never use blocks on or under the jack.
•Do not start or run the engine while the
vehicle is on the jack. The vehicle may move
suddenly, and this may cause an accident.
•Never allow passengers to stay in the ve-
hicle while the tire is off the ground.
•Remove all loads before lifting the vehicle
with the jack.
NOTE
A jack and rod are not provided as standard
equipment with your vehicle. These parts are
dealer options. It is recommended that you con-
tact an INFINITI retailer for more information
about obtaining these parts. 1. Place the jack directly under the jack-up
point as illustrated so that the top of the jack
contacts the vehicle at the jack-up point.
The jack must be placed on firm level ground.NCE453NCE447Jack-up points
6-6In case of emergency

2. Align the center of both the jack head2and the notches at the jack-up point3as
shown.
3. Fit the groove of the jack head between the two notches as shown. 4. Loosen each wheel bolt by one or two turns
counterclockwise with the wheel wrench.
Do not remove the wheel bolts until the tire is
off the ground.
Models with wheel lock bolts (if equipped) :
If the wheel is equipped with a wheel lock
bolt, insert the wheel lock key
1and
loosen it as previously described.
The wheel lock bolt can only be removed
with the wheel lock key. A key number is
necessary if you need to duplicate the wheel
lock key. Record the key number as shown on the key
code card on the “Security information”
page at the end of this manual and keep it in
a safe place, not in the vehicle. If you lose
the wheel lock key, it is recommended you
see your INFINITI retailer for a duplicate with
the original wheel lock key code.
Make sure to keep the lock key in the
vehicle. Otherwise, wheels cannot be re-
moved and the service cannot be performed.
NCE449NCE143Z
In case of emergency6-7

5. To lift the vehicle, securely hold and turn theratchet handle
1clockwise as shown.
6. Carefully raise the vehicle until the tire clears the ground.
7. Remove the wheel bolts, then remove the wheel with the flat tire.
WARNING
The wheel is heavy. Be sure that your feet are
clear of the wheel and use gloves as necessary
to avoid injury.
Installing the wheel
WARNING
•A temporary use spare wheel and tire is de-
signed for emergency use.
•Never use wheel bolts other than those pro-
vided with your vehicle. Incorrect wheel
bolts or improperly tightened wheel bolts
may cause the wheel to become loose or
come off. This could cause an accident.
•Never use oil or grease on the wheel bolts.
This may cause the wheel bolts to become
loose.ATighten
BLoosen
1. Clean any mud or dirt from the surface between the wheel and the hub.
2. Carefully fit the wheel and tighten the wheel bolts with your fingers. Check that all the
wheel bolts contact the wheel surface hori-
zontally and on the bevelled side.
Models with wheel lock bolt (if equipped):
Insert the wheel lock key into the wheel lock
bolt and tighten into the wheel finger tight.
3. With the wheel wrench, tighten the wheel bolts alternately and evenly in the sequence
as illustrated (
1-5) until they are tight.
4. Lower the vehicle slowly until the tire touches the ground.
NCE449NCE435
6-8In case of emergency

5. Tighten the wheel bolts securely using thewheel wrench in the sequence as illustrated.
6. Lower the vehicle completely.
7. Install the wheel cover (if equipped).
Wheel
bolt tightening torque:96 ft-lb (130 N•m, 13
kg-m)
As soon as possible, tighten the wheel bolts to
the specified torque with a torque wrench.
The wheel bolts must be kept tightened to
specification at all times. It is recommended
that the wheel bolts be tightened to specifica-
tion at each maintenance interval.
Adjust the tire pressure to the COLD pressure.
COLD pressure is the tire pressure as measured
after the vehicle has been parked for three
hours or more or driven for less than 1 mile (1.6
km).
COLD tire pressures are shown on the tire and
loading information label affixed to the driver’s
side center pillar.
Wheel lock bolts (if equipped)
In order to prevent theft, the specially designed
wheel lock bolt is installed to each wheel. The
wheel lock bolt cannot be removed with the
commonly used tools. When removing tires, use the lock key provided
with your vehicle.
Removing the wheel lock bolt
:
1. Insert the wheel lock key1to the wheel
lock bolt.
2. To remove the wheel lock bolt, turn the wheel lock key counterclockwise using the
wheel wrench.
CAUTION
•Do not use a power tool to remove the wheel
lock bolts.
•When installing the wheel, tighten the
wheel lock bolts to the same tightening
torque as the normal wheel bolts. For de-
tails, see Installing the wheel earlier in
this section. NOTE
•The wheel lock bolt has an individual code. A
wheel lock key with other than the individual
code cannot remove the wheel lock bolt. If
you lose the wheel lock key, it is recom-
mended you contact an INFINITI retailer for a
duplicate with the original wheel lock key
code.
•Record the key number and keep it in a safe
place, not in the vehicle.
•When you ask for a service at an INFINITI
retailer, make sure to keep the lock key in
the vehicle. Otherwise, wheels cannot be
removed and the service cannot be per-
formed.
NCE143Z
In case of emergency6-9

Two-Wheel Drive (FWD) models
CAUTION
NEVER tow automatic transmission (DCT) mod-
els with the front wheels on the ground or with
all four wheels on the ground (forwards or
backwards), as this may cause serious and ex-
pensive damage to the transmission. If it is
necessary to tow the vehicle with the rear
wheels raised, always use towing dollies un-
der the front wheels.
Four-Wheel Drive (4WD) models
INFINITI recommends that towing dollies be
used under the front or rear wheels when
towing your vehicle or the vehicle be placed on
a flatbed tow truck as illustrated.
CAUTION
Never tow 4WD models with any of the wheels
on the ground. Doing so will cause serious and
expensive damage to the drivetrain.
Vehicle recovery (freeing a stuck
vehicle)
WARNING
To avoid vehicle damage, serious personal in-
jury or death when recovering a stuck vehicle:
•Contact a professional towing service to re-
cover the vehicle if you have any questions
regarding the recovery procedure.
•Tow chains or cables must be attached only
to the vehicle recovery hooks or main struc-
tural members of the vehicle.
•Do not use the vehicle tie downs to tow or
free a stuck vehicle.
•Only use devices specifically designed for
vehicle recovery and follow the manufactur-
er’s instructions.
•Always pull the recovery device straight out
from the front of the vehicle. Never pull at an
angle.
•Route recovery devices so they do not touch
any part of the vehicle except the attach-
ment point.
If your vehicle is stuck in sand, snow, or mud,
and the vehicle is unable to free itself without
NCE4504WD models
In case of emergency6-15

being pulled, use the recovery hook stored in
the vehicle trunk.
WARNING
•Use the recovery hook only. Do not attach
the pulling device to any other part of the
vehicle body. Otherwise, the vehicle body
may be damaged.
•Use the recovery hook to free a vehicle only.
Never tow a vehicle using only the recovery
hook.
•The recovery hook is under tremendous
stress when used to free a trapped vehicle.
Always pull the pulling device straight out
from the vehicle. Never pull on the recovery
hook at an angle.
Securely install the recovery hook (stored in the
vehicle trunk) to the attaching mount located on
the front or rear bumper.
Make sure that the recovery hook is properly
secured in its storage location after use and the
license plate is properly reinstalled before driv-
ing the vehicle.
Rocking a stuck vehicle
WARNING
•To avoid potential injury, stand clear of a
stuck vehicle.
•Do not spin your tires at high speed. This
could cause them to explode and result in
serious injury. Parts of your vehicle could
also overheat and be damaged.
If your vehicle is stuck in sand, snow, mud, etc.,
use the following procedure:
1. Turn off the Vehicle Dynamic Control (VDC) system.
2. Make sure the area in front and behind the vehicle is clear of obstructions.
3. Turn the steering wheel right and left to clear an area around the front tires.
4. Slowly rock the vehicle forward and back- ward.
•Shift back and forth between R (Reverse) and
D (Drive).
•Apply the accelerator as little as possible to
maintain the rocking motion.
•Release the accelerator pedal before shifting
between R (Reverse) and D (Drive).
•Do not spin the tires above 35 MPH (55
km/h).
5. If the vehicle cannot be freed after a few tries, contact a professional towing service
to remove the vehicle.
6-16In case of emergency

7 Appearance and care
Cleaning exterior...................... .7-2
Washing ..........................7-2
Waxing .......................... .7-2
Removing spots ..................... .7-3
Underbody .........................7-3
Glass ........................... .7-3
Wheels .......................... .7-3
Aluminum alloy wheels ..................7-3
Chrome parts ...................... .7-3
Tire dressings ...................... .7-4
Cleaning interior ....................... .7-4Air fresheners
...................... .7-4
Floor mats (if equipped) .................7-5
Seat belts ..........................7-5
Cleaning the seat tracks .................7-5
Genuine leather seat covers ..............7-6
Corrosion protection .................... .7-6
Most common factors contributing to vehicle
corrosion ..........................7-6
Environmental factors influence the rate of
corrosion ..........................7-6
To protect your vehicle from corrosion ........7-7

In order to maintain the appearance of your
vehicle, it is important to take proper care of it.
To protect the paint surfaces, please wash your
vehicle as soon as you can:
•After a rainfall, to prevent possible damage
from acid rain.
•After driving on coastal roads.
•When contaminants such as soot, bird drop-
pings, tree sap, metal particles or bugs get
on the paint surface.
•When dust or mud builds up on the surface.
Whenever possible, park your vehicle inside a
garage or in a covered area to minimize the
chances of damaging the paint surface of your
vehicle.
When it is necessary to park outside, park in a
shady area or protect the vehicle with a body
cover. Be careful not to scratch the paint surface
when putting on or removing the body cover.
WASHING
Wash dirt off with a wet sponge and plenty of
water. Clean the vehicle thoroughly using a mild
soap, a special vehicle soap or general purpose
dishwashing liquid mixed with clean, lukewarm
(never hot) water.
CAUTION
•Do not use car washes that use acid in the
detergent. Some car washes, especially
brushless ones, use some acid for cleaning.
The acid may react with some plastic vehicle
components, causing them to crack. This
could affect their appearance, and also
could cause them not to function properly.
Always check with your car wash to confirm
that acid is not used.
•Do not wash the vehicle with strong house-
hold soap, strong chemical detergents,
gasoline or solvents.
•Do not wash the vehicle in direct sunlight or
while the vehicle body is hot, as the paint
surface may become water-spotted.
•Avoid using tight-napped or rough cloths,
such as washing mitts. Care must be taken
when removing caked-on dirt or other for-
eign substances so the paint surface is not
scratched or damaged.
Rinse the vehicle thoroughly with plenty of
clean water.
Inside edges, seams and folds on the doors,
hatches and hood are particularly vulnerable to
the effects of road salt. Therefore, these areas must be cleaned regularly. Take care that the
drain holes in the lower edge of the door are
open. Spray water under the body and in the
wheel wells to loosen the dirt and wash away
road salt.
A damp chamois can be used to dry the vehicle
to avoid water spots.
WAXING
Regular waxing protects the paint surface and
helps maintain a new vehicle appearance.
After waxing, polishing is recommended to re-
move built-up residue and to avoid a weathered
appearance.
An INFINITI retailer can assist you in choosing
the appropriate waxing products.
•Wax your vehicle only after a thorough wash-
ing. Follow the instructions supplied with the
wax.
•Do not use a wax containing any abrasives,
cutting compounds or cleaners that may
damage the vehicle finish.
Machine compounding or aggressive polishing
on a base coat/clear coat paint finish may dull
the finish or leave swirl marks.
CLEANING EXTERIOR
7-2Appearance and care