2017 FIAT QUBO lock

DIPPED/MAIN BEAM HEADLIGHTS
To change the bulb (double filament), proceed as
follows:
remove the protective lid A fig. 145;
release the bulb holder clip;
remove the bulb A fig. 147 from connector B and
replace it;
refit the new bulb by inserting it on connector B
and then make the contour of the metallic part
mate with the grooves obtained on the headlight
parabola;
refit the bulb holder clip and refit the protective
lid A fig. 145 correctly.DIRECTION INDICATORS
Front
To change the bulb, proceed as follows:
turn the protective lid B fig. 145 anticlockwise;
remove the bulb A fig. 148 and replace it;
refit the protective lid B correctly.
fig. 147F0T0095fig. 148F0T0096
161
KNOWING YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING AND
CARE
TECHNICAL DATA
INDEX

Side lights
To change the bulb, proceed as follows:
operate the lens A fig. 149 to press in the internal
catch B fig. 150, then pull the unit outwards;
turn the bulb holder C anti-clockwise, extract
bulb D and replace it;
refit the bulb holder C in the lens and turn it
clockwise;
refit the unit making sure that the internal catch B
clips into position.FOG LIGHTS
(for versions/markets, where provided)
IMPORTANT Contact Fiat Dealership to replace the
front fog lights.
fig. 149F0T0097fig. 150F0T0098
162
KNOWING YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING AND
CARE
TECHNICAL DATA
INDEX

THIRD BRAKE LIGHTS
Tailgate versions
To replace the bulbs, proceed as follows fig. 155 -
fig. 156:open the tailgate and loosen the two retaining
screws A;
disconnect the electrical connector B;
release the retainer tab C and open the bulb
holder assembly;
extract the snap-fitted bulb and replace it.
NUMBER PLATE LIGHTS
Proceed as follows to replace the bulbs A fig. 157:
operate the holding tabs at the points indicated by
the arrows, and remove the bulb holder;
turn the bulb holder B fig. 158 anticlockwise and
then remove the bulb C.
fig. 155F0T0212
A
C
A
B
fig. 156F0T0443fig. 157F0T0104
165
KNOWING YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING AND
CARE
TECHNICAL DATA
INDEX

CHANGING AN INTERIOR BULB
For the type of bulb and corresponding power rating,
see the paragraph "Changing a bulb".
FRONT CEILING LIGHT
Ceiling light with movable lens
To change the bulbs, proceed as follows:
extract the ceiling light A fig. 159 by operating in
the points shown by the arrows;
open the lid B fig. 160 as shown;
remove bulb C fig. 160 by releasing it from the
side contacts, then insert the new bulb and make
sure it is correctly clamped between these
contacts;
close the lid and secure the ceiling light into its
housing, making sure it locks properly into place.Roof light with spot lights
(for versions/markets, where provided)
To change the bulbs, proceed as follows:
operate in the points shown by the arrows and
remove ceiling light A fig. 161;
open the protective lid B fig. 162;
fig. 158F0T0105
fig. 159F0T0106
fig. 160F0T0458
166
KNOWING YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING AND
CARE
TECHNICAL DATA
INDEX

replace the bulbs C releasing them from the side
contacts and making sure that the new bulbs are
correctly secured between the contacts;
re-close the lid B fig. 162 and secure light A
fig. 161 into its housing locking it properly.REAR CEILING LIGHT
To change the bulb, proceed as follows:extract the ceiling light A fig. 163 by operating in
the points shown by the arrows;
open the lid B fig. 164 as shown;
remove bulb C fig. 164 by releasing it from the
side contacts, then insert the new bulb and make
sure it is correctly clamped between these
contacts;
close the lid B and secure the ceiling light into its
housing, making sure it locks properly into place.
fig. 161F0T0143
fig. 162F0T0144fig. 163F0T0107
167
KNOWING YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING AND
CARE
TECHNICAL DATA
INDEX

press the tab A fig. 170 and remove the fuse box
protective lid B;
move the lid towards the headlight, turning it
anticlockwise (as shown by the arrow) and then
remove it fig. 171;
the fuse box can be accessed in this manner
fig. 173.
If you need to clean the engine
compartment , take care not to direct the
jet of water specifically onto the engine
compartment wired casing.
fig. 170F0T0172fig. 171F0T0173
171
KNOWING YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING AND
CARE
TECHNICAL DATA
INDEX

PROTECTED DEVICE - fig. 175 FUSE AMPS
Dipped headlight (passenger side)
F12
(*)7,5
Dipped headlight (driver side)/Headlight alignment corrector F13
7,5/5
(*)
INT/A SCM relay coils F31 5
Timed interior lighting
F32
(*)7,5
Radio
Bluetoothfisystem node/Blue&Me™ node/EOBD diagnostic socket/
Volumetric alarm ECU/Alarm siren ECUF36 10
Instrument panel node/Stop light control (NO) F37 5
Door/luggage compartment lock actuators
(*)F38 20
Windshield washer/rear window washer bidirectional pump F43 15
Front electric window (driver side)
(*)F47 20
Front electric window (passenger side)
(*)F48 20
Control lights/Parking sensors ECU/Electric wing mirrors/Volumetric alarm
ECUF49 5
INT Radio node/
Bluetoothfisystem ECU/Blue&Me™ node/Electric wing
mirrors movement/Clutch switch/
Brake light control (NC)F51 7.5
Instrument panel node F53 5
External mirror defrosters F41 7.5
SpareF45 -
SpareF46 -
SpareF90 -
(*)For versions/markets, where provided
176
KNOWING YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING AND
CARE
TECHNICAL DATA
INDEX

WARNING
Before towing, turn the ignition key to
MAR and then to STOP without
extracting it .The steering column will
automatically lock when the key is removed and
the wheels cannot be steered.
WARNING
Before tightening the hook clean the
threaded housing thoroughly. Before
towing the vehicle, make sure that the tow ring
is fully tightened in its appropriate housing.
WARNING
Do not start the engine whilst the
vehicle is being towed.
WARNING
Remember that the brake booster will
not work while the vehicle is being
towed and that more pressure must be applied
to the pedal. Do not use bendy cables for
towing and avoid jerking. During towing
operations, make sure that the fastened joint
does not damage adjoining components.When
towing the vehicle, comply with the specific
rules of the highway code regarding the towing
device and road conduct . Do not start the
engine whilst the vehicle is being towed.
fig. 179F0T0086
181
KNOWING YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING AND
CARE
TECHNICAL DATA
INDEX