Page 40 of 530

WARNING!
Avoid trapping anyone in the vehicle in a collision.
Remember that the sliding doors can only be opened
from the outside door handle or the switches located
on the B-Pillar trim panel just in front of the power
sliding door when the Child Protection Door Locks are
engaged.
To Disengage The Child Protection Door Lock
1. Open the sliding side door.
2. Slide the Child Protection Door Lock control outward(away from the vehicle) to disengage the Child Protec-
tion Door Lock.
3. Repeat Steps 1 and 2 on the opposite sliding door (if equipped). NOTE:
•
After setting the Child Protection Door Lock system,
always test the door from the inside to make certain it is
in the desired position.
• The power sliding side door switches will not open the
power sliding doors if the vehicle is in gear or the
vehicle speed is above 0 mph (0 km/h).
• The power sliding door will operate from the outside
door handle, the key fob, the switches on the overhead
console, or the switches located on the B-pillar trim
panel, just in front of the power sliding door when the
gear selector is in PARK, regardless of the child lock
lever position.
LIFTGATE
On vehicles equipped with power locks, the liftgate can be
unlocked using the key fob button, or by activating the
power door lock switches located on the front doors.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Page 41 of 530
To open the liftgate, push the liftgate release handle located
on the underside of the license plate bar and pull the
liftgate open with one fluid motion.
Power Liftgate — If Equipped
The power liftgate may be opened manually or by using
the button on the key fob. Push the button on the key fob
twice within five seconds, to open the power liftgate. When
the liftgate is fully open, pushing the button twice within
five seconds, a second time, will close the liftgate.The power liftgate may also be opened and closed by
pushing the button located on the overhead console.
The power liftgate may be closed by pushing the button,
located in the upper left trim in the liftgate opening.
Pushing once will only close the liftgate. This button
cannot be used to open the liftgate.
Liftgate Handle Location
Overhead Console Master Power Switch
1 — Left Sliding Door
2 — Liftgate
3 — Right Sliding Door
4 — Power Switch
2
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39
Page 42 of 530

When the key fob button is pushed and the Flash Lights
feature is enabled, the tail lights will flash and several
audible beeps will occur to signal that the liftgate is
opening or closing.
WARNING!
During power operation, personal injury or cargo
damage may occur. Ensure the liftgate travel path is
clear. Make sure the liftgate is closed and latched
before driving away.NOTE:
•
If anything obstructs the power liftgate while it is
closing or opening, the liftgate will automatically re-
verse to the closed or open position, provided it meets
sufficient resistance.
• There are also pinch sensors attached to the side of the
liftgate opening. Light pressure anywhere along these
strips will cause the liftgate to return to the open
position.
• During power operation, whether liftgate is fully open
or fully closed, the liftgate chime will beep several times
indicating power operation is in progress.
• The power liftgate must be in the full open or close
positions for any of the buttons to operate. If the liftgate
is not in the full open or close positions, it must be
opened or closed manually.
• If the liftgate release button is activated while the power
liftgate is closing, the liftgate will reverse to the full open
position.
• The power liftgate buttons will not operate if the gear
selector is in gear or the vehicle speed is above 0 mph
(0 km/h).
Rear Power Liftgate Switch
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Page 100 of 530

▫Power Seats — If Equipped ...............141
▫ Power Lumbar — If Equipped .............144
▫ Heated Seats — If Equipped ..............144
▫ Manual Front/Second Row Seat Adjuster .....146
▫ Manual Reclining Seats — If Equipped .......147
▫ Head Restraints .......................147
▫ Stow ’n Go Seating — If Equipped ..........151
▫ Quad Seats — If Equipped ................157
▫ Second Row Bench Seat — If Equipped .......160
▫ Third Row Power Recline — If Equipped ......161
▫ Third Row Power Folding Seat — If Equipped . .162
▫ Manually Folding Third Row Seats — If
Equipped ............................164
▫ Plastic Grocery Bag Retainer Hooks ..........167
DRIVER MEMORY SEAT — IF EQUIPPED .....167
▫ Programming The Memory Feature ..........167
▫ Linking And Unlinking The Remote Keyless Entry
Key Fob To Memory .....................168 ▫
Memory Position Recall ..................169
▫ Easy Entry/Exit Seat (Available With Memory Seat
Only) ...............................169
TO OPEN AND CLOSE THE HOOD ..........170
LIGHTS ............................. .172
▫ Headlight Switch ..................... .172
▫ Automatic Headlights — If Equipped ........173
▫ Headlights On With Wipers — If Equipped . . . .173
▫ Headlight Delay — If Equipped ............173
▫ Lights-On Reminder ....................174
▫ Daytime Running Lights — If Equipped ......174
▫ Front
Fog Lights — If Equipped ............174
▫ Dimmer Controls ..................... .174
▫ Multifunction Lever ....................176
▫ Turn Signals ..........................176
▫ Lane Change Assist .....................176
▫ High/Low Beam Switch .................176
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Page 169 of 530

WARNING!
To avoid serious injury or death, never operate the
vehicle with occupants in the third row seat while in
the tailgate mode.
Plastic Grocery Bag Retainer Hooks
Retainer hooks which will hold plastic grocery bag handles
are built into the seatbacks of all rear seats and some front
seats. The floor supports the partial weight of the bagged
goods.
DRIVER MEMORY SEAT — IF EQUIPPED
The Memory Buttons 1 and 2 on the driver’s door panel can
be programmed to recall the driver’s seat, outside mirrors,
and radio station preset settings. Your Remote Keyless
Entry key fob can also be programmed to recall the same
positions when the UNLOCK button is pushed.Your vehicle may have been delivered with two key fobs,
one key fob can be linked to each of the memory positions.
Programming The Memory Feature
To create a new memory profile, perform the following:
1. Cycle the vehicles ignition to the ON/RUN position (do
not start the engine).
2. Adjust all memory profile settings to desired prefer- ences (i.e., driver ’s seat, outside mirrors, adjustable
pedals [if equipped] and radio station presets).
Driver Memory Switch
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167
Page 170 of 530

3. Push and release the S (Set) button on the memoryswitch.
4. Within five seconds, push and release either of the memory buttons (1) or (2). The instrument cluster dis-
play will display which memory position has been set.
NOTE:
• Memory profiles can be set without the vehicle in PARK,
but the vehicle must be in PARK to recall a memory
profile.
• To set a memory profile to your key fob, refer to
“Linking And Unlinking The Remote Keyless Entry Key
Fob To Memory” in this section.
Linking And Unlinking The Remote Keyless Entry
Key Fob To Memory
Your key fobs can be programmed to recall one of two
pre-programmed memory profiles by pushing the UN-
LOCK button on the key fob.
NOTE: Before programming your key fobs you must select
the “Remote Keyless Entry Linked To Memory” feature
through the instrument cluster display. Refer to “Instru-
ment Cluster Display” in “Understanding Your Instrument
Panel” for further information. To program your key fobs, perform the following:
1. Cycle the vehicles ignition to the OFF position.
2. Select a desired memory profile (1) or (2).
NOTE:
If a memory profile has not already been set, refer
to Programming The Memory Feature in this section for
instructions on how to set a memory profile.
3. Once the profile has been recalled, push and release the SET (S) button on the memory switch.
4. Push and release button (1) or (2) accordingly. “Memory Profile Set” (1 or 2) will show in the instrument cluster
display.
5. Push and release the LOCK button on the key fob within 10 seconds.
NOTE: Your key fobs can be unlinked to your memory
settings by pushing the SET (S) button, and within 10
seconds, followed by pushing the UNLOCK button on the
key fob.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Page 171 of 530

Memory Position Recall
NOTE:The vehicle must be in PARK to recall memory
positions. If a recall is attempted when the vehicle is not in
PARK, a message will be displayed in the instrument
cluster display.
To recall the memory settings for driver one, push
MEMORY button 1 on the driver’s door or the UNLOCK
button on the key fob linked to memory position 1.
To recall the memory setting for driver two, push
MEMORY button 2 on the driver’s door or the UNLOCK
button on the key fob linked to Memory Position 2.
A recall can be cancelled by pushing any of the MEMORY
buttons on the driver’s door during a recall (S, 1, or 2).
When a recall is cancelled, the driver’s seat, and the pedals
(if equipped) stop moving. A delay of one second will
occur before another recall can be selected.
NOTE: Pushing the mirror adjust switch will cancel the
memory mirror recall.
Easy Entry/Exit Seat (Available With Memory Seat
Only)
This feature provides automatic driver seat positioning to
enhance driver mobility when entering and exiting the
vehicle.
The distance the driver seat moves depends on where you
have the driver seat positioned when you remove the key
from the ignition switch.
• When you remove the key from the ignition switch, the
driver seat will move about 2.4 inches (60 mm) rearward
if the driver seat position is greater than or equal to 2.7
inches (67.7 mm) forward of the rear stop. The seat will
return to its previously set position when you insert the
key into the ignition switch and turn it out of the LOCK
position.
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169
Page 177 of 530

Interior lights are also turned on when a door or liftgate is
opened, the Remote Keyless Entry key fob is activated, or
when the dimmer control is moved to the extreme top.
The interior lights will automatically turn off in approxi-
mately 10 minutes for the first activation and 90 seconds
every activation thereafter until the engine is started, if one
of the following occur:
•A door, sliding door or the liftgate is left open.
• Any overhead reading light is left on.
NOTE: The ignition must be cycled to the OFF position for
this feature to operate.
Interior Lighting Off
Rotate the left dimmer control to the off position (extreme
bottom). The interior lights will remain off when the doors
or liftgate are open.
Parade Mode (Daytime Brightness Feature)
Rotate the left dimmer control to the first detent. This
feature brightens the odometer, radio and overhead dis-
plays when the parking lights or headlights are on.
Halo Lights — If Equipped
Halo lights are strategically placed soft lighting that help to
illuminate specific areas to aid the occupants in locating
specific features while driving at night.
The Halo control switch is located to the right of the
dimmer switch.
To activate the Halo lights, rotate the Halo switch
control upward or downward to increase or
decrease the lighting.
Halo Control
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175