2017 CITROEN RELAY headlamp

24
Level 2 display screen
In the left-hand part:
-
T
ime,
-

Ambient temperature,
-


Alert or state indicators,
-


Cruise control or speed limiter
.
In the right-hand part:
-

Date,
-


Service indicator
,
-

T
rip computer (range, fuel
consumption...),
-

Alert messages,
-


Messages on the state of systems,
-


V
ehicle configuration,
-

Headlamp beam height,
-


Miles
/ kilometres travelled.
Level 2 instrument panel

/ display screen
Instruments and controls

30
Warning/indicator lampisindicates Solution - action
Diesel pre-
heater on.the ambient temperature
necessitates pre-heating. Wait until the lamp goes off before operating the starter.
Dipped beam on.a manual selection.
Turn the lighting control stalk ring to the second
position.
Main beam the control stalk has been
pulled towards you.Pull the lighting control stalk again to return to dipped
beam.
Automatic
headlamp
dipping on.
activation of the function in
the
"MODE" menu.The headlamps are dipped automatically according to
the driving conditions and traffic.
"Technology on board - Vehicle configuration" section.
Direction
indicators flashing with
buzzer.a change of direction using the
lighting stalk. To the Right: press the stalk upwards.
To the Left: press the stalk downwards.
Front foglamps on. the button on the MODE control
panel has been pressed.Manual selection.
The foglamps only operate if the dipped beam
headlamps are on.
Rear foglamps on. the button on the MODE control
panel has been pressed.Manual selection.
The rear foglamps only operate if the dipped beam
headlamps are on.
When visibility is normal, switch them off.
Cruise control on.the cruise control has been
selected. Manual selection.
"Ease of use and comfort - Steering mounted controls"
section.
Instruments and controls

31
Screendisplays indicates Solution - action
Temperature /
Ice the ice warning,
the temperature
flashing
accompanied by
a message in
the screen.weather conditions which could
result in ice on the road.
Be particularly vigilant and do not brake sharply.
"Safety - Driving safely".
Date
/ Timea setting: date,
time. a configuration via the "MODE"
menu.
"Technology on board
- Vehicle configuration" section.
Headlamp beam
height a headlamp
beam height
setting.a position from 0 to 3
depending on the load carried. Adjust using the buttons in the MODE control panel.
"Ease of use and comfort - Steering mounted controls"
section.
Service spanner a service
spanner which
remains on.a service will soon be due.
Refer to the list of checks in the manufacturer's service
schedule, then have the service carried out.
Stop & Start on.
engine going into STOP mode
after the vehicle stops. As soon as you want to move off, the warning lamp
goes off and the engine restarts automatically in
START


mode.
flashes for a few
seconds, then
goes off. STOP mode temporarily
unavailable.
Special cases for STOP mode.
"Ready to go
- Starting and stopping" section.
2
rEAdY tO GO
Instruments and controls

48
LIGHtInG cOntrOL S tALK
d irection indicators
(green flashing)
Left: downwards.
Right: upwards.
Sidelamps on
d

ipped / Main beam
headlamps on
Switching between dipped and main
beam
Pull the control stalk fully towards you.
Headlamp flash
Pull the control stalk towards you,
regardless of the position of the ring.
Front foglamps
r

ear foglamps
If your vehicle is fitted with foglamps, these
operate with the dipped or main beam
headlamps.
Press one of these controls to switch on the
lamps. The foglamps should only be used in
fog or when snow is falling.
In clear weather or in rain, both day and
night, rear foglamps dazzle and their use is
prohibited.
Do not forget to switch them off when they
are no longer necessary."Motorway" function
Pull the lever towards the steering wheel
with a press, without passing the point
of resistance of the lighting stalk; the
corresponding direction indicators will flash
five times.
Selection is by rotation of the white mark on
the ring.
Steering mounted controls

49AutOMAtI c ILL u MI n At IO n
Activation
Turn the ring to this position.
Do not cover the sunshine sensor at
the top centre of the windscreen.
GuIdE-ME-HOME LIGHtInG
Ignition off or key in the StOP
position.
Within 2 minutes after switching off the
engine, position the ignition key in the STOP
position or remove it.
Pull the lighting stalk towards the steering
wheel.
t

he indicator lamp comes on in
the instrument panel.
Each action on the lighting stalk,
pulled towards the steering
wheel, prolongs the guide me home
lighting by 30 seconds up to approximately
3
minutes. When this time has elapsed, the
lamps are switched off automatically.
Deactivate this control by keeping the stalk
pulled towards the steering wheel for more
than 2 seconds. If your vehicle is fitted with this function:
when you leave your vehicle, the dipped
beam headlamps remain on for the selected
duration (when leaving a car park for
example).
You can adjust the sensitivity of the
sunshine sensor.
Refer to the "Technology on board -
Vehicle configuration" section.
If your vehicle is fitted with this function, the
dipped beam headlamps are switched on
automatically if the light is poor.
In fog or snow, the sunshine sensor may
detect sufficient light. Therefore, the lamps
will not be switched on automatically. If
necessary, you must switch on the dipped
beam headlamps manually.
They are switched off when the light returns
to a sufficient level.
LEd dAYtIME runnInG LAMPS
On starting the vehicle, in daylight the LED
daytime running lamps come on automatically.
If the sidelamps and headlamps are switched
on manually or automatically, the daytime
running lamps go off.
Programming
For countries where exterior lighting by
day is not a legal requirement, you can
activate or deactivate the function via the
configuration menu.
The lamps are switched off automatically
when the ignition is switched off.
3
EASE OF uSE and cOMFOrt
Steering mounted controls

51Activation
Operation
Once the function is activated, the system
operates as follows:
If the ambient light level is sufficient and/or if
the traffic conditions do not allow illumination
of the main beam headlamps:Refer to the "Technology on board -
Vehicle configuration" section.
F
Flash the headlamps (going beyond the


point of resistance) to activate the function. If the situation requires a change of
headlamp beam, the driver can take over at
any time.
F
Flashing the headlamps again pauses


the function and the system changes to
"automatic illumination of headlamps"
mode.
The function is deactivated automatically
below 9 mph (15 km/h).
If main beam is still needed, flash the
headlamps again; main beam will then
remain on until the vehicle reaches a speed
of 25 mph (40 km/h).
Above 25 mph (40 km/h), the function is
reactivated automatically (provided that the
headlamps have not been flashed again in
the meantime, to change to dipped beam).
d

eactivation
F
T

urn the lighting control stalk ring to the
"
d

ipped beam" position.The system may suffer interference or
not work correctly:
-

Under conditions of poor visibility

(falling snow, heavy rain or dense
fog, ...),
-

If the windscreen is dirty
, misted or
obscured (by a sticker, ...) in front
of the camera,
-

If the vehicle is facing highly

reflective signs.
The system is not able to detect:
-

Road users that do not have their

own lighting, such as pedestrians,
-

V
ehicles whose lighting is
obscured, such as when running
behind a safety barrier on a
motorway, for example,
-

V
ehicles at the top or bottom of a
steep slope, on winding roads, on
crossroads.
-

Dipped beam is maintained,

this indicator lamp comes on
in the instrument panel.
If the ambient light level is very low and the
traffic conditions permit: -

Main beam comes on

automatically: these
indicator lamps come
on in the instrument
panel.
F
T

urn the lighting control stalk
ring to this position.
F
Activate the function with the

MO d E
button; in the "Automatic headlamp
dipping" menu, select "ON".
3
EASE OF uSE and cOMFOrt
Steering mounted controls

52
HEAdLAMP BEAM
You are advised to adjust the height of the
headlamp beams in accordance with the
load in your vehicle.
This function works in the dipped and main
beam headlamps position.Press these controls, located
on the dashboard, several times
in succession to adjust the
headlamps.
An indicator in the screen shows
the adjustment position selected
(0, 1, 2, 3).
PArKInG LAMPS
This system enables you to leave the lamps
on when parked; with the ignition off, key in
the STOP position or key removed.
Move the ring on the lighting stalk to position
O then to dipped or main beam headlamps.
t

he indicator lamp in the
instrument panel comes on.
The lamps will remain on while
you are parked.
Leaving the lighting on for long periods may
significantly reduce the state of charge of
your vehicle's battery.
travelling abroad
If using your vehicle in a country

that drives on the other side of the road,
the headlamps must be adjusted to avoid
dazzling on-coming drivers.
Contact a CITROËN dealer or a qualified
workshop.
Steering mounted controls

53
WIPEr cOntrOL S tALKSlow continuous wiping: 2 notches downwards.
Do not cover the rain sensor, located at
the top centre of the windscreen.
Screenwash and headlamp wash
Pull the wiper control stalk towards you,
the screenwash is accompanied by a timed
operation of the wipers.
Depending on version, the headlamp wash is
coupled with the screenwash, it is triggered if
the dipped beam headlamps are on.
Windscreen wipers
Wiping is only active when the ignition key is
in the runn I n G position.
The control stalk has five different positions:
Wipers off.
Intermittent wiping: 1 notch downwards.
In this position, four wiping frequencies
can be selected by turning the ring:
-

very slow frequency
-


slow frequency
-


standard frequency
,
-

fast frequency
.
Automatic rain sensitive windscreen
wipers
If your vehicle is fitted with this system, the
wiping speed is adapted automatically to the
intensity of the rainfall.
Automatic wiping: 1 notch downwards. This is
confirmed by one wipe. Must be reactivated
each time the ignition is switched on.
In this position, the sensitivity of the rain
sensor can be increased by turning the ring.
Good practice
Check that the windscreen wiper blades can
operate freely when using the wipers in icy
weather.
Use the step in the front bumper, to remove
any accumulation of snow at the base of the
windscreen and on the blades.You can change the wiper blades.
Refer to the "Quick help - Worn wiper
blade" section.
You can check the fluid level.
Refer to the "Checks - Levels and
checks" section.
Fast continuous wiping: 3 notches
downwards.
Single wipe: pull the control stalk towards
the steering wheel.
With Stop & Start, when the wiper
control stalk is in the fast wipe position,
the STOP mode is not available.
When washing the vehicle, switch off the
ignition or deactivate the automatic rain
sensitive wipers.
3
EASE OF uSE and cOMFOrt
Steering mounted controls