2017 Citroen GRAND C4 PICASSO RHD boot

86
Flat floor
Folding a seat
F Pull firmly upwards on strap C, as indicated
by the arrow, to release the seat; keep
pulling until the seat is fully folded.
P

ush the seat backrest gently for wards
so that the backrest folds onto the seat
cushion. The assembly lowers onto the
f l o o r. You can fold the second-row seats from the
boot, after first folding the third-row seats.
F

P
ull on the strap D to release the seat in
question then push for wards lightly on the
backrest.
T

o avoid any damage to the mechanism,
the strap D
unclips if too much force is
applied. Simply clip it in place again for the
system to be operational again.
F

P

lace the seats in the fully back position.
Each seat can be folded onto the floor to vary
the space available in the boot.
From the outside
From the boot, when loading
for example
Ease of use and comfort

87
Repositioning a seat
Before operating the rear seats, check
that the outer rear seat belts are not
loose, to avoid damaging them. The
centre belt must be stowed. Fix the
tongues of the three belts to their
anchorage points.
Continuity panels
These continuity panels are not
designed to support a weight greater
than 30 kg.Releasing / locking the continuity panels
F

B
efore unfolding the continuity panels,
check that the seats in the 2
nd row are fully
back.
F

S

lide the continuity panel latch upwards to
release.
F

S

traighten the continuity panel, then slide
the latch downwards to lock it.
F

I

f necessary, straighten the continuity
panels for the seats in the 2
nd row and lock
them in place.
F

R

aise the backrest and push it rear wards
until it locks in position Each seat has a continuity panel at the bottom
of the backrest, that once unfolded:
-
p rovides a continuous load sur face in the
boot, whatever the position of the seats,
-

a
voids objects sliding under the seats in
the 2
nd row.
3
Ease of use and comfort

95
In order for these systems to be fully effective, follow the operation and maintenance
guidelines below:
F
T
o obtain an even air distribution, take care not to obstruct the exterior air intake grilles
located at the base of the windscreen, the nozzles, the vents and the air outlets, as well
as the air extractor located in the boot.
F

D
o not cover the sunshine sensor, located on the dashboard; this is used for regulation
of the air conditioning system.
F

O
perate the air conditioning system for at least 5 to 10 minutes, once or twice a month
to keep it in per fect working order.
F

E
nsure that the passenger compartment filter is in good condition and have the filter
elements replaced regularly.
W

e recommend the use of a combined passenger compartment filter. Thanks to its
special active additive, it contributes to the purification of the air breathed by the
occupants and the cleanliness of the passenger compartment (reduction of allergic
symptoms, bad odours and greasy deposits).
F

T
o ensure correct operation of the air conditioning system, you are also advised to have
it checked regularly as recommended in the maintenance and warranty guide.
F

I
f the system does not produce cold air, switch it off and contact a CITROËN dealer or a
qualified workshop.
Recommendations for ventilation and air conditioning
If after an extended stop in sunshine,
the interior temperature is very high, first
ventilate the passenger compartment for
a few moments.
Put the air flow control at a setting high
enough to quickly change the air in the
passenger compartment.
The condensation created by the air
conditioning results in a discharge
of water under the vehicle which is
per fectly normal.
When towing the maximum load on a steep gradient in high temperatures, switching off the
air conditioning increases the available engine power and so improves the towing ability.
Stop & Start
The heating and air conditioning
systems only work when the engine is
running.
To maintain a comfortable temperature
in the passenger compartment, you can
temporarily deactivate the Stop & Start
system.
For more information on Stop & Star t ,
refer to the corresponding section.
3
Ease of use and comfort

109
Removable console
The removable console is a portable storage space secured to the lower centre console.
It has a sliding lid, an open storage space and two cup holders.
F
R
aise the locking control located at the
front of the console.
F

W
ith one hand, lift the front part of the
console.
F

W
ith the other hand, grasp the rear part to
release the removable console. F

C
arry out these operations in reverse
order. Ensure that the console has locked
into place.
When not fixed to its carrier, the
removable console should be stowed
in the boot. It could become a projectile
in the event of a sudden stop or violent
impact.
Releasing the removable
console Refitting the removable
console
Central storage compartment
F To open the central storage compartment,
pull the grip and lower the cover.
It is illuminated on opening.
A button on the upper part allows the lighting to
be deactivated.
Depending on equipment, it may contain:
-

o
ne 12 V socket,
-

o
ne USB port,
-

o
ne auxiliary socket
3
Ease of use and comfort

114
Boot fittings
1. Rear parcel shelf (see details on a following page)
2.
H

ooks
(

see details on a following page)
3.


To r c h
(

see details on a following page)
4.
St

orage net
5.
L

ashing rings
6.
1

2 V socket (maximum power: 120 Watts)
Ease of use and comfort

115
To remove the shelf:
F u nhook the two cords,
F

r
aise the shelf slightly, then remove it.
Rear parcel shelf
There are several options for storing the shelf:
- e ither upright behind the front seats,
-

o
r flat at the base of the boot. The hooks can be used to secure shopping
bags.
Hooks
3
Ease of use and comfort

116
Boot fittings
1. Luggage cover roller (see details on a following page)
2.
T

o r c h
(

see details on a following page)
3.
C

oncertina boards
4.
1

2 V socket (maximum power: 120 Watts)
5.
A

rmrest with cup holder and storage space
6.
L

ocation for stowing the luggage cover
roller
7.
O

pen storage
8.
L

ower lashing rings
Ease of use and comfort

117
Luggage cover roller
In the 5 -seat configuration, it is installed behind
the second-row seats, with the third-row seats
folded away.
In the 7-seat configuration, it is stowed behind
the third row seats.F

P
osition the left and right-hand ends of the
roller in cut-out A , with the mobile flap at
the front.
F

P
ull out the roller until it reaches the boot
pillars.
F

I
nsert the guides of the roller into the rails
on the pillars B . F

D
isengage the roller guides from the rails
in the pillars B .
F

G
uide the roller as it is reeled in.
F

U
nlock the roller by pressing one of the
grips located at the ends of the roller
support.
The mobile flap allows passengers in
the second row to place their seats in
the "comfort" position.Installation Removal
3
Ease of use and comfort