2017 Citroen GRAND C4 PICASSO Lamp

290
C4-Picasso-II_en_Chap08_en-cas-panne_ed02-2016
F Switch on the compressor by moving the switch B to position "I" until the tyre
pressure reaches 2.0 bars.
T

he sealant is injected into the tyre under
pressure; do not disconnect the pipe from
the valve during this operation (risk of
splashing).
If after around 5 to 7 minutes the
pressure is not attained, this indicates
that the tyre is not repairable; contact
a CITROËN dealer or a qualified
workshop for assistance. F
R emove the kit and screw the cap back on
the white pipe.
T

ake care to avoid staining your vehicle
with traces of fluid. Keep the kit to hand.
F

D
rive immediately for approximately
three miles (five kilometres), at reduced
speed (between 12 and 37 mph (20 and
60
km/h)), to plug the puncture.
F

S
top to check the repair and the tyre
pressure using the kit.
Tyre under-inflation detection
After repair of the tyre, the warning
lamp will remain on until the system is
reinitialised.
For more information on Under-
inflation detection , refer to the
corresponding section.
In the event of a breakdown

300
C4-Picasso-II_en_Chap08_en-cas-panne_ed02-2016
Removing a wheel
Parking the vehicle
Immobilise the vehicle where it does not
block traffic: the ground must be level,
stable and not slippery.
Apply the parking brake unless it has
been programmed to automatic mode,
switch off the ignition and engage first
gear* to block the wheels.
Check that the braking warning lamp
and the P warning lamp in the parking
brake control lever come on.
For greater safety, place the chock 2
against the wheel opposite to the one
being changed.
The occupants must get out of the
vehicle and wait where they are safe.
Never go underneath a vehicle
supported by a jack; use an axle stand.
List of operations
F Remove the wheel bolt cover(s) using the tool 4 (depending on equipment).
F

F
it the security socket 5 on the
wheelbrace


1 to slacken the security bolt
(if
fitted).
F

S
lacken the other bolts (no more than a
1/4
turn) using the wheelbrace 1 o n l y.
* Position P for an automatic gearbox. Do not use:
-

t
he jack for any purpose other than
lifting the vehicle,
-

a
ny other jack than the one
supplied by the manufacturer. F

P
lace the foot of the jack 3 on the ground
and check that it is directly below the
front A or rear B jacking point provided on
the underbody, whichever is closest to the
wheel to be changed.
Ensure that the jack is stable. If the
ground is slippery or loose, the jack
may slip or drop - Risk of injury!
Ensure that the jack is positioned only
at one of the jacking points A or B
under the vehicle, making sure that the
vehicle's contact sur face is centred on
the head of the jack. Other wise there is
a risk of damage to the vehicle and/or of
the jack dropping - Risk of injury!
In the event of a breakdown

304
C4-Picasso-II_en_Chap08_en-cas-panne_ed02-2016
Changing a bulb
For H7 type bulbs with lugs... take care
to observe their correct installation
so as to ensure the best lighting
performance.
Risk of electrocution
Xenon bulbs (D5S-25W) must be
replaced by a CITROËN dealer or a
qualified workshop.
Front lamps
1. Directional dipped beam headlamps (D5S-25W).
2.
M

ain beam headlamps (H7-55W).
3.
D

aytime running lamps / sidelamps
(

6 light emitting diodes - LEDs).
4.
D

irection indicators
(

6 light emittng diodes - LEDs).
5.
F

ront foglamps (H11-55W). 1. D
ipped beam headlamps (H7-55W).
2. M ain beam headlamps (H7-55W).
3.
D

aytime running lamps/sidelamps
(

4 light emitting diodes - LEDs).
4.
D

irection indicators (PW Y24W).
5.
F

oglamps (H11-55W).In some weather conditions (e.g. low
temperature or humidity), the presence
of misting on the internal sur face of the
glass of the headlamps and rear lamps
is normal; it disappears after the lamps
have been on for a few minutes.
Light- emitting diodes - LEDs
For replacement, contact a CITROËN dealer or
qualified workshop.
Model with xenon headlamps Model with halogen headlamps
In the event of a breakdown

305
C4-Picasso-II_en_Chap08_en-cas-panne_ed02-2016
Directional dipped beam
headlamps (xenon model)Main beam headlamps (xenon model)
F Remove the protective plastic cover by pulling the tab.
F

P
ush the connector.
F

R
emove the bulb and change it.
For reassembly, carry out these operations in
reverse order.
D5S xenon bulbs must be changed
by a CITROËN dealer or a qualified
workshop, as there is a risk of
electrocution.
In the event of failure of one of
the D5S bulbs, it is recommended that
the bulb on the other side be changed
at the same time.
The headlamps have polycarbonate
lenses with a protective coating:
F

d

o not clean them using a dr y
or abrasive cloth, nor with a
detergent or solvent product,
F

u

se a sponge and soapy water or
a

pH neutral product,
F

w

hen using a high pressure washer
on persistent marks, do not keep
the lance directed towards the
lamps or their edges for too long,
so as not to damage their protective
coating and seals.
Changing a bulb should only be done
after the headlamp has been switched
off for several minutes (risk of serious
burns).
F

D

o not touch the bulb directly with
your fingers, use a lint-free cloth.
It is imperative to use only anti-
ultraviolet (UV) type bulbs to avoid
damaging the headlamp.
Always replace a failed bulb with a
new bulb with the same type and
specification.
8
In the event of a breakdown

306
C4-Picasso-II_en_Chap08_en-cas-panne_ed02-2016
Dipped beam headlamps
(halogen model)
F Remove the protective plastic cover by pulling the tab.
F

P
ush the connector.
F

R
emove the bulb and change it.
For reassembly, carry out these operations in
reverse order.
Main beam headlamps
(halogen model)
F Turn the protective plastic cover to remove it.
F

D
isconnect the connector.
F

R
elease the clips.
F

R
emove the bulb and change it.
For reassembly, carry out these operations in
reverse order.
In the event of a breakdown

307
C4-Picasso-II_en_Chap08_en-cas-panne_ed02-2016
The direction indicator bulb is located below
the front lamp.
F
T
urn the bulb holder a quarter turn anti-
clockwise.
F

R
emove the bulb holder.
F

C
hange the failed bulb.
For reassembly, carry out these operations in
reverse order.
Direction indicators Front foglamps
F Unclip the finisher by pulling at the top.
F
R emove the two screws to remove the unit.
F

T
urn the bulb holder a quarter turn.
F

R
emove the bulb holder.
F

C
hange the failed bulb.
For reassembly, carry out these operations in
reverse order, pressing on the finisher to refit it.
Faster flashing of a direction indicator
warning lamp (left or right) indicates a
failed bulb on that side.
Direction indicators
(light- emitting diodes - LED)
For the replacement of this type of lamp,
contact a CITROËN dealer or a qualified
workshop.
8
In the event of a breakdown

308
C4-Picasso-II_en_Chap08_en-cas-panne_ed02-2016
You should contact a CITROËN dealer or a
qualified workshop for the replacement of the
light-emitting diode - LED.
Door mirror spotlamps
Integrated direction indicator
side repeaters
You should contact a CITROËN dealer or a
qualified workshop for the replacement of these
bulbs.1.
D

irection indicators (PY21W amber).
2.
S
idelamps / foglamps (P21/5W).
Rear lamps
Light-emitting diodes -
LEDs
For replacement, contact a CITROËN
dealer or qualified workshop.
3.
B

rake lamps / sidelamps (light-emitting
diodes - LEDs).
4. R
eversing lamps (W16W).
5.
D

irection indicators (PY21W).
Model with LED lamps3. Sidelamps (5W5).
4. B rake lamps (P21/ W).
5.
D

irection indicators (W Y16W).
6.
R

eversing lamps (W16W).
Model with conventional bulb lamps
In the event of a breakdown

309
C4-Picasso-II_en_Chap08_en-cas-panne_ed02-2016
Lamps on the tailgate
To change a sidelamp and brake lamp bulb:
F T urn the bulb holder a quarter of a turn
anti-clockwise and pull the bulb out.
F

C
hange the bulb.
Identify the failed bulb.
F

O

pen the boot.
F

R

emove the access cover.
F

R

emove the three lamp fixing screws A
.
F

D

isconnect the lamp connector.
F

C

arefully remove the lamp from the outside
by pressing the retaining clip B .
To change a reversing lamp or direction
indicator bulb:
F
U
se a standard pair of pliers to turn the
bulb holder a quarter turn anticlockwise,
and pull it out.
F
C
hange the bulb.
For reassembly, carry out these operations in
reverse order.
Model with LED lamps Model with conventional bulb lamps
8
In the event of a breakdown