2017 Citroen GRAND C4 PICASSO Lamp

218
C4-Picasso-II_en_Chap05_eclairage-visibilite_ed02-2016
The system may suffer inter ference or
not work correctly:
-
u
nder conditions of poor visibility
(falling snow, heavy rain or thick
fog, etc.),
-

i
f the windscreen is dirty, misted or
obscured (by a sticker, etc.) in front
of the camera,
-

i
f the vehicle is facing highly
reflective signs.
The system is not able to detect:
-

r
oad users that do not have their
own lighting, such as pedestrians,
-

r
oad users whose lighting is
obscured, such as vehicles running
behind a safety barrier (on a
motor way, for example),
-

r
oad users at the top or bottom of a
steep slope, on winding roads, on
crossroads.
Deactivation
F In the Driving menu, select the " Driving
functions " tab, then " Automatic
headlamp dipping "; the system changes
to "automatic illumination of headlamps"
mode.
To reactivate the system, flash the headlamps
again.
Depending on the situation,
these indicator lamps
come on.
Activation
F Put the lighting control stalk ring
in the " AUTO" position.
F

I

n the Driving menu, select the " Driving
functions " tab, then " Automatic
headlamp dipping ".
Operation
- dipped beam is
maintained, these
indicator lamps come on in
the instrument panel.
F

F
lash the headlamps
(going beyond the point
of resistance) to activate
the function.
Once the function is activated, the system
operates as follows:
If the ambient light level is sufficient and/or if
the traffic conditions do not allow illumination of
the main beam headlamps:
If the ambient light level is very low and the
traffic conditions permit: -

m
ain beam comes on
automatically: these
indicator lamps come on in
the instrument panel.
Pause
If the situation requires a change of headlamp
beam, the driver can take over at any time.
F

F
lashing the headlamps
again pauses the
function and the system
changes to "automatic illumination of
headlamps" mode:
-

i
f the "AUTO" and "Dipped beam"
indicator lamps are on, the system
changes to main beam,
-

i
f the "AUTO" and "Main beam" indicator
lamps are on, the system changes to
dipped beam.
Lighting and visibility

219
C4-Picasso-II_en_Chap05_eclairage-visibilite_ed02-2016
To make your approach to the vehicle easier,
these illuminate:
-
t
he zones facing the driver’s and
passenger’s doors,
-

t
he zones for ward of the door mirrors and
rear ward of the front doors.
Door mirror spotlamps
Switching on
Switching off
They go off automatically after 30 seconds.
Exterior welcome
lighting
Switching on
F Press the open padlock on the remote control or one of the front
door handles with Keyless Entry
and Starting.
Front daytime running
lamps
(light-emitting diodes)
They come on automatically when the engine
is started, when the lighting control stalk is in
position " 0" or " AUTO ".
In some weather conditions (e.g. low
temperature or humidity), the presence
of misting on the internal sur face of the
glass of the headlamps and rear lamps
is normal; it disappears after the lamps
have been on for a few minutes. The remote switching on of the lighting makes
your approach to the vehicle easier in poor
light. It is activated when the lighting control
is in the "
AUTO" position and the level of light
detected by the sunshine sensor is low.
Switching off
The exterior welcome lighting switches off
automatically after a set time, when the ignition
is switched on or on locking the vehicle.
When the courtesy lamp is in this
position, the spotlamps come on
automatically:
-
w
hen you unlock the vehicle,
-

w

hen you remove the electronic key from
the reader,
-

w

hen you open a door,
-

when you use the remote control to locate the vehicle.
The dipped beam headlamps and sidelamps
come on; your vehicle is also unlocked.
5
Lighting and visibility

220
C4-Picasso-II_en_Chap05_eclairage-visibilite_ed02-2016
To avoid causing a nuisance to other road
users, the headlamps should be adjusted
according to the load in the vehicle.
0.
1 o
r 2 people in the front seats.
-.
I

ntermediate setting.
1.
5 p

eople + maximum authorised load.
-.
I

ntermediate setting.
2.
D

river + maximum authorised load.
-.
I

ntermediate setting.
3.
5 p

eople + maximum load in the boot.
Adjusting the headlamp
beam height
The initial setting is position "0" .
Programming
The activation, deactivation and choice of
welcome lighting duration are done via the
Driving menu of the touch screen.
On the " Vehicle settings " tab, select
" Welcome lighting ".
Use the arrows or the cursor to adjust the
duration of the lighting.
Direction indicators
F Left: lower the lighting stalk passing the point of resistance.
F

R
ight: raise the lighting stalk passing the
point of resistance.
Three flashes of the direction
indicators
F Press briefly upwards or downwards, without going beyond the point of
resistance; the direction indicators will
flash 3 times.
Lighting and visibility

221
C4-Picasso-II_en_Chap05_eclairage-visibilite_ed02-2016
Cornering lighting
This system, if fitted to your vehicle, makes use
of the beam from a front foglamp to illuminate
the inside of a bend, when the main or dipped
beam headlamps are on and the vehicle speed
is below 25 mph (40 km/h) (urban driving,
winding road, junctions, parking manoeuvres,
e t c .) .with cornering lighting
without cornering lighting
Switching on
This system starts:
-
w hen the corresponding direction indicator
is switched on,
or
-

f
rom a certain angle of rotation of the
steering wheel.
Switching off
The system does not operate:
- b elow a certain angle of rotation of the
steering wheel,
-

a
bove 25 mph (40 km/h),
-

w
hen reverse gear is engaged.
The cornering lighting can be activated or
deactivated in the Driving menu.
F

Sel
ect the " Vehicle settings " tab, then
" Driving lighting " and "Directional
headlamps ".
5
Lighting and visibility

222
C4-Picasso-II_en_Chap05_eclairage-visibilite_ed02-2016
Directional lighting
When the dipped or main beam headlamps are
on, this system allows the light beams to better
follow the road.
Associated with xenon headlamps, this system
improves the quality of lighting when cornering.with directional lighting
without directional lightingOperating fault
This system is inactive:
- w hen stationary or at low speeds,
-
w

hen reverse is engaged. If a fault occurs, these warning lamps
come on in the instrument panel,
accompanied by an audible signal
and a message.
Contact a CITROËN dealer or a qualified
workshop.
The directional lighting can be activated or
deactivated in the touch screen.
In the Driving menu, select the " Vehicle
settings " tab, then " Driving lighting " and
select " Directional headlamps ".
Lighting and visibility

225
C4-Picasso-II_en_Chap05_eclairage-visibilite_ed02-2016
Screenwash and washer jets
Windscreen wash and headlamp wash
Adjusting the jets
The front washers include an adjustment for the
height of delivery from the jets.
If you want to modify the factory setting, turn
the screw on each jet anti-clockwise, towards
the "+" to raise the jet or clockwise, towards
the "-" to lower it.
Headlamp wash
F Pull the windscreen wiper stalk towards you. The windscreen wash then the
windscreen wipers operate for a fixed
period.
A few moments after releasing the wiper stalk,
there is a last wipe to clear any runs from the
screen. The headlamps operate when the vehicle is
moving and when the dipped beam headlamps
are on. However, to reduce the consumption
of screenwash fluid, the headlamp wash only
operates with every 7th use of the screenwash
or once every 25 miles (40 km), during a given
j o u r n ey.
5
Lighting and visibility

226
C4-Picasso-II_en_Chap05_eclairage-visibilite_ed02-2016
Do not cover the rain sensor, linked with
the sunshine sensor and located in the
centre of the windscreen behind the rear
view mirror.
Switch off the automatic rain sensitive
wipers when using an automatic car wash.
In winter, it is advisable to wait until the
windscreen is completely clear of ice
before activating the automatic rain
sensitive wipers.
Operating fault
If a fault occurs with the automatic rain
sensitive wipers, the wipers will operate in
intermittent mode.
Have it checked by CITROËN dealer or a
qualified workshop.
The windscreen wipers operate automatically, without any action on the part of the driver, if rain is
detected (sensor behind the rear view mirror), adapting their speed to the intensity of the rainfall.
Switching on
Switching off
The automatic rain sensitive windscreen
wipers must be reactivated by pushing
the control stalk downwards, if the
ignition has been off for more than
one
minute.
Briefly push the control stalk
downwards.
A wiping cycle confirms that the
instruction has been accepted.
This warning lamp comes on in the
instrument panel and a message is
displayed. Briefly push the control stalk
downwards again, or place
the control stalk in another
position
(Int, 1 or 2).
Automatic rain sensitive windscreen wipers
This warning lamp goes off in the instrument
panel and a message is displayed.
Lighting and visibility

230
C4-Picasso-II_en_Chap06_securite_ed02-2016
Hazard warning lamps
Visual warning with all of the direction
indicators flashing to alert other road users to a
vehicle breakdown, towing or accident.
F
P
ress this button, all of the direction
indicators flash.
They can operate with the ignition off.
Automatic operation of
hazard warning lamps
When braking in an emergency, depending on
the deceleration, the hazard warning lamps
come on automatically.
They switch off automatically the first time you
accelerate.
F

Y
ou can also switch them off by pressing
the button.
Horn
F Press the central part of the steering wheel.
Safety