2017 CITROEN C-ELYSÉE ignition

103
Starting the engine
The parking brake must be applied.
F

W

ith a manual gearbox, place the gear
lever in neutral then depress the clutch
pedal fully.
F

W

ith an automatic gearbox, select position
P, then firmly press the brake pedal.
F

W

ith an electronic gearbox, select position
N then firmly press the brake pedal.
F

I

nsert the key into the ignition switch; the
system recognises the code.
F

U

nlock the steering column by
simultaneously turning the steering and the
key.
In certain cases, you may have to turn
the steering wheel energetically to move
the wheels (for example if the wheels are
braced against a kerb). F
W ith a petrol engine, operate the starter
motor by turning the key to position 3
without pressing the accelerator pedal,
until the engine starts. Once the engine is
running, release the key.
F

W
ith a Diesel engine, turn the key to
position 2 , ignition on, to operate the
engine pre-heating system.
Wait until this warning light goes off
in the instrument panel then operate
the starter motor by turning the key
to position 3 without pressing the
accelerator pedal, until the engine
starts. Once the engine is running,
release the key.
In winter conditions, the lighting time of
the indicator light is longer. When the
engine is warm, the indicator light does
not come on. If the engine does not start immediately,
turn off the ignition. Wait a few minutes
before restarting. If after a few attempts
the engine does not start, do not persist:
you risk damaging the starter and the
engine. Contact a
CITROËN dealer or a
qualified workshop.
In temperate conditions, do not leave
the engine at idle to warm up but move
off straight away and drive at moderate
speed.
Never leave the engine running in
an enclosed area without adequate
ventilation: internal combustion engines
emit toxic exhaust gases, such as carbon
monoxide. There is a risk of poisoning and
death!
In severe wintry conditions (temperature
below -23°C), the engine should be left at
idle for four minutes before moving off to
ensure the correct operation and life of the
mechanical parts of your vehicle, engine
and gearbox.
6
Driving

104
Switching off the engine
F Stop the vehicle.Energy savings mode
For more information on the Energy
economy mode refer to the
corresponding section.
F

W

ith the engine running in idle, turn the key
to position 1 .
F

R

emove the key from the ignition switch.
F

T

o lock the steering column, turn the
steering until it locks.
To facilitate unlocking of the steering column,
it is recommended that the wheels be
returned to the straight ahead position
before switching off the engine.
F

C

heck that the parking brake is
correctly applied, particularly on
sloping ground. After switching off the engine (position
1- Stop
), for a maximum of 30 minutes you
can still use functions such as the audio and
communications system, the wipers, dipped
beam headlights, courtesy lights, ...
Never turn the ignition off before the
vehicle is at a complete stop. With the
engine off, the braking and steering
assistance systems are also cut off: risk
of loss of control of the vehicle.
When you leave the vehicle, keep the key
with you and lock the vehicle.
When opening the driver's door, an alert
message is displayed, accompanied by
an audible signal, to remind you that the
key is still in the ignition switch at position
1 (Stop) .
If the key has been left in the ignition
switch at position 2 (Ignition on) , the
ignition will be switched off automatically
after one hour.
To switch the ignition back on, turn the key
to position 1 (Stop) , then back to position
2 (Ignition on) .
Key left in the "Ignition on" position
Driving

105
Parking brake
LockingUnlocking
F Pull the parking brake lever up slightly,
press the release button, then lower the
lever fully.
When parking on a slope, direct your
wheels against the kerb, apply the parking
brake, engage a gear and switch off the
ignition. When the vehicle is being driven,
if this warning light and the STOP

warning light come on, accompanied
by an audible signal and a message
in the screen, this indicates that the
parking brake is still on or has not
been fully released.
Manual gearbox
Engaging reverse gear
F Press the clutch pedal fully down.
F

P
ush the gear lever fully to the right then
backwards.
F

P

ull the parking brake lever up to
immobilise your vehicle.
As a safety precaution and to facilitate
starting of the engine:
-

a
lways select neutral,
-

p
ress the clutch pedal.
Only engage reverse gear when the
vehicle is stationary with the engine at idle.
6
Driving

109
Stopping the vehicle
Before switching off the engine, you can:
- m ove to position N to engage neutral,
or
-

l
eave the gear engaged; in this case, it will
not be possible to move the vehicle.
For all parking situations, you must apply
the parking brake to immobilise the
vehicle.
In case of immobilization of the vehicle,
engine running, absolutely put the gearbox
in neutral N .
Before working in the engine
compartment, ensure that the gear
selector is in neutral N and the parking
brake is applied.
Reinitialisation
Following disconnection of the battery, you
have to reinitialise the gearbox.
F
S
witch on the ignition.AUTO and - appear in the
instrument cluster.
F

Sel
ect position N .
F

P
ress the brake pedal.
F

W
ait for approximately 30 seconds until N
or a gear appears in the instrument cluster.
F

M
ove the gear selector to position A , then
to position N .
F

W
ith your foot still on the brake pedal, start
the engine.
The gearbox is operational again. Exceptionally, it may be necessary to
reinitialise the gearbox automatically: in
such a case the vehicle won't start and no
gear change will happen.
Malfunction
or
With the ignition on, if this warning
light comes on and AUTO
flashes,
accompanied by an audible signal
and a message in the multifunction
screen, this indicates a gearbox
fault.
Have them checked by a
CITROËN dealer or a
qualified workshop. AUTO
and - appear in the
instrument cluster.
Follow the procedure described above.
6
Driving

112
Automatic operation
F Select position D for automatic changing
of the six gears.
The gearbox then operates in auto-adaptive
mode, without any action needed from the
driver. It continuously selects the most suitable
gear according to the style of driving, the profile
of the road and the load in the vehicle.
To obtain maximum acceleration without
touching the selector, press the accelerator
pedal all the way down (kick down). The
gearbox changes down automatically or
maintains the gear selected until the maximum
engine speed is reached.
When braking, the gearbox changes down
automatically to provide effective engine
braking.
If you release the accelerator sharply, the
gearbox will not change to a higher gear for
safety reasons.
Never select position N while the vehicle
is moving.
Never select positions P or R unless the
vehicle is completely stationary.Reverse gear
When selecting reverse R with the ignition
on, the rear parking sensors are activated
automatically.
For more information on Rear parking
sensors , refer to the corresponding section.
Autonomous traction function
(moving without using the
accelerator)
This function facilitates manoeuvring of the
vehicle at low speed (when parking, in traffic
jams, …).
With the engine at idle, parking brake released
and position D , M or R selected, the vehicle
moves as soon as you take your foot off
the brake pedal (even without pressing the
accelerator).
Sport and snow
programmes
These two special programmes supplement the
automatic operation in very specific conditions
of use.
Sport programme "S"
F Press button S, after starting the engine.
The gearbox automatically favours a dynamic
style of driving.
S appears in the instrument panel.
Driving

114
Stopping the vehicle
Before switching off the engine, you can
engage position P or N to place the gearbox in
neutral.
In both cases, apply the parking brake to
immobilise the vehicle.If the selector is not in position P , when the
driver's door is opened or approximately
45 seconds after the ignition is switched
off, a warning message appears in the
screen.
F

R
eturn the selector to position P ; the
message disappears.
When driving on flooded roads or when
crossing a ford, proceed at walking pace.
Malfunction
or When the ignition is on, the lighting
of this warning light, accompanied
by an audible signal and a message
in the screen, indicates a gearbox
fault.
In this case, the gearbox goes into back-up
mode by staying in 3rd gear. You may feel a
substantial knock when changing from P to
R and from N to R . This will not cause any
damage to the gearbox.
Do not exceed 60 mph (100 km/h), local speed
restrictions permitting.
Contact a
CITROËN dealer or a qualified
workshop as soon as possible. There is a risk of damage to the gearbox:
-

i
f you press the accelerator and brake
pedals at the same time,
-
i
f you force the movement of the
selector from the P position to another
position when the battery is dead.
To reduce fuel consumption when at
a prolonged standstill with the engine
running (traffic jam, etc.), put the
selector in the N position and apply the
parking brake.
Driving

116
Stop & Start
The Stop & Start system puts the engine
temporarily into standby - STOP mode - during
stops in the traffic (red lights, traffic jams, or
other...). The engine restarts automatically -
START mode - as soon as you want to move
off. Restarting occurs instantly, quickly and
silently.
Per fect for urban use, the Stop & Start system
reduces fuel consumption and exhaust
emissions as well as the noise level when
stationary.Operation
Going into engine STOP mode
For your comfort, during parking
manoeuvres, STOP mode is not available
for a few seconds after coming out of
reverse gear.
The STOP mode does not affect the
operation of vehicle systems such as
braking, power steering...
Never refuel with the engine in STOP
mode; you must switch off the ignition
using the key.With an electronic gearbox, the
"ECO" indicator illuminates in the
instrument panel and the engine
goes into standby when and the
brake pedal is pressed or the gear
selector is moved into position N
while the vehicle is stationary.
Special cases: STOP mode not
available
STOP mode is not invoked when:
-
T he driver's door is open.
-

T
he driver's seat belt is not fastened.
-

T
he engine is needed to maintain a
comfortable temperature in the passenger
compartment.
-

D
emisting is active.
-
S

ome special conditions (battery charge,
engine temperature, braking assistance,
climate control...) need it to control the
system.
The "ECO" warning light flashes for
a few seconds, then goes off.
This operation is perfectly normal.
Driving

117
Manual deactivation /
reactivation
In certain circumstances, such as the need
to maintain the temperature in the passenger
compartment, it may be useful to deactivate the
Stop & Start system.
The system can be deactivated at any time,
once the ignition is switched on.
If the engine is in STOP mode, it then restarts.
The Stop & Start system is reactivated
automatically every time the ignition is switched
on.Going into engine START mode
- you release the brake pedal with the gear selector in position A or M ,
-

y
ou are in position N with the brake pedal
released and you move the gear selector to
position A or M,
-
y

ou engage reverse.With an electronic gearbox, the
"ECO" warning light goes off and the
engine restarts automatically when:
Special cases: START mode
invoked automatically
As a safety measure or to maintain comfort
levels in the vehicle, START mode is invoked
automatically when:
-
Y

ou open the driver's door.
-
Y

ou unfasten the driver's seat belt.
-

T
he speed of the vehicle exceeds 2 mph
(3
km/h) with an electronic gearbox.
-
S

ome specific conditions (battery charge,
engine temperature, braking assistance,
climate control, etc.) need it to ensure
control of a system or the vehicle.
The "ECO" warning light flashes for
a few seconds, then goes off.
This operation is perfectly normal.
6
Driving