47
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Instruments and controls
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
SERVICE INDICATOR
This programmes service intervals
according to the use of the vehicle.More than 1 000 miles/km before the
next service is due
Example:
4 800 miles/km remain
before
the next service is due. When
the ignition is switched on and for a
few
seconds, the screen shows:
A few seconds after the ignition is
switched on, the oil level is displayed
(depending on version), then the total
distance recorder resumes normal
operation showing the total and trip
distances.
Less than 1 000 miles/km before the
next service is due
Each time the ignition is switched on and for a few
seconds, the spanner flashes and the number of miles/kilometres
remaining is displayed:
A few seconds after the ignition is
switched on, the oil level is displayed
(depending on version), then the total
distance recorder resumes normal
operation
and the spanner remains on.
This indicates that a service should be
carried
out shortly.
Service overdue
Operation
A few moments after the ignition
has been switched on, the spanner
indicating a service operation comes
on; the display for the total distance
recorder
gives
(in
round
figures)
the
distance remaining before the next
service.
The points at which a service is due
are calculated from the last indicator
zero
reset.
The point at which a service is due is
determined
by
two
parameters:
-
the distance travelled,
-
the time which has elapsed since
the
last
service.
The distance remaining before the
next service may be weighted by
the time factor, depending on the
type
of
driving. With the engine running the spanner
remains on until the service has been
carried
out.
For BlueHDi Diesel versions, this
alert
is also accompanied by the fixed
illu
mination of the Service warning
lamp,
on switching on the ignition.
Each time the ignition is
switched on and for a few
seconds, the spanner
flashes
and the excess
distance
is displayed.
For BlueHDi Diesel versions, the
spanner can also come on early,
according the level of deterioration
of
the engine oil. Deterioration of the
engine oil depends on the conditions of
use
of the vehicle.
READY TO GO
3
48
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Instruments and controls
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Trip recorder zero
reset button
After this operation, if you wish
to disconnect the battery, lock
the
vehicle and wait for at least five
minutes, otherwise the zero re-set will
not
be registered.
Engine oil level indicator
Depending on your vehicle's engine,
when the ignition is switched on,
the engine oil level is indicated for
a few seconds, after the service
information. Oil level
correct
Low oil level
Flashing of "OIL",
linked
with the
service warning lamp,
accompanied by an
audible signal and a message in the
screen, indicates a low oil level which
could
damage the engine.
If the low oil level is confirmed by a
check
using the dipstick, it is essential
that
the level is topped up.
Oil level gauge
fault
Flashing of "OIL--"
indicates a
malfunction of the
engine oil level indicator. Contact
a
CITROËN dealer or a qualified
workshop.
The level read will only be correct
if the vehicle is on level ground
and the engine has been of
f for
more
than 30 minutes.Dipstick
A = maximum, never exceed
this level as a surplus of oil
may
damage the engine.
Contact a CITROËN dealer
or a qualified workshop
without
delay.
B = minimum, top up the level
via the oil filler cap, using the
grade of oil suited to your
engine.
Lighting dimmer
With the ignition on, press
the button until the zeros
appear.
With the lighting on,
press the button to vary
the brightness of the
instruments
and controls.
When the lighting reaches
the minimum
(or maximum) setting, release the
button then press it again to increase
(or
reduce)
the brightness.
As soon as the lighting is of the
required
brightness, release the button.
Zero reset
Your CITROËN dealer or a qualified workshop carries out this operation
after
each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
-
switch of
f the ignition,
-
press and hold the trip recorder
reset button,
-
switch
on the ignition.
The
display begins a countdown.
When the display shows "=0", release
the
button; the spanner disappears.
