2017 Citroen BERLINGO MULTISPACE RHD warning

161
Berlingo2VP_en_Chap07_Verification_ed02-2016Berlingo2VP_en_Chap07_Verification_ed02-2016
REFUELLING
Low fuel level
Filling
The  fuel   tank   must   be   filled   with the
engine off.
-
 
Open
  the   fuel   filler   flap.
-
 
Insert
  the   key,   then   turn   it   a   quarter  
turn.
-

 
Remove
  the   cap   and   hook   it   onto  
the clip located on the inside of the
flap. When

  filling   with   fuel,  a
mechanical system prevents
opening
  of   the   left-hand   side   door.  
When

  the   fuel   filler   flap   is   open,   ensure  
that

  no   one   tries   to   slide   this   door.
Once
  the   flap   has   been   closed,   the  
sliding

  side   door   may   jam,   push   the  
door

  to   close   it   then   open   it.
When the low fuel level is
reached, this warning lamp
comes
 
on. A
 

label   affixed   to   the   inside   of   the   flap  
reminds you of the type of fuel to be
used.
Y

ou   must   fill   with   at   least   5   litres   of   fuel  
for

  it   to   be   registered   by   the   fuel   gauge.
When
  the   fuel   filler   cap   is   opened,  
there

  may   be   a   slight   inrush   of   air.  
This
 
vacuum is entirely normal and is due to
the

  sealing   of   the   fuel   system.
When
  filling   the   fuel   tank,   do   not  
continue after the 3rd cut-off of the
nozzle.
 This
 
could
 
cause   malfunctions.
The
 
capacity
 
of
 
the
 
fuel   tank   is  
approximately 60 litres (or 55 litres
according

 
to
 
version).
-
 
After

 
filling
 
the
 
fuel   tank,   lock   the  
cap

 
and
 
close
 
the   flap.
You then have approximately 8 litres
of
 
fuel
 
remaining.
Fill up without delay to avoid running
out
 
of
 
fuel.
Never
 
risk
 
driving
 
until
 
you
 
run
 
out
 
of
 
fuel as this may damage the emissions
control

 
and
 
injection
 
systems.
CHECKS
7
Fuel

163
Berlingo2VP_en_Chap07_Verification_ed02-2016Berlingo2VP_en_Chap07_Verification_ed02-2016
DIESEL PRIMING
PUMP
If you run out of fuel, it is necessary to
prime
  the   fuel   circuit.
Other HDi engines
- Fill  the   fuel   tank   with   at   least   five  litres
  of   Diesel.
-

Squeeze and release the manual
priming pump, under the bonnet,
under

  the   protective   cover.
-

Operate the starter until the engine
starts.
BlueHDi engine
- Fill   the   fuel   tank   with   at   least   five  litres
  of   Diesel.
-

Switch on the ignition (without
starting

  the   engine).
-

W
ait around 6 seconds and switch
off
  the   ignition.
-
 
Repeat
  the   operation   10   times.
-

Operate the starter to run the
engine.
FUEL CUT- OFF
In a serious collision, a mechanism
automatically prevents fuel from
reaching
  the   engine.
The
  flashing   of   this   warning  
lamp is accompanied by a
message

  in   the   screen.
Check
  that   there   is   no   odour   or  
leakage

  of   fuel   outside   the   vehicle   and  
re-establish

  the   fuel   supply:
-

switch of
f the ignition
(STOP


position),
-
 
remove
  the   key,
-
 
put
  the   key   back   in   the   ignition,
-
 
switch
  on   the   ignition   and   start.
CHECKS
7
AdBlue®

165
Berlingo2VP_en_Chap07_Verification_ed02-2016Berlingo2VP_en_Chap07_Verification_ed02-2016
Good practice
While the quantity of AdBlue® in
the
 
additive
 
tank
 
is
 
sufficient,
 
no
 
information

 
is
 
displayed.
On
 
the
 
other
 
hand,
 
once
 
the
 
fluid
 
level drops to the quantity needed
for

 
a
 
range
 
of
 
1
 
500
 
miles
 
(2
 
400
 
km)  
driving, you are warned by dif

ferent
temporary signals (warning lamp,
message,
 
audible
 
signal).
As more miles are covered, these
signals intensify and the message
becomes
 
permanent.
When the AdBlue
® tank is empty, restarting
 
becomes   impossible.
It is strongly recommended that you
do not wait for the successive alerts
before topping-up the AdBlue
® additive,
but
 
do
 
this
 
as
 
soon
 
as
 
possible.
Filling the AdBlue® tank
For light vehicles, 5 or 10 litre
containers
 
and
 
1.89
  litre  
(1/2 US gallon)

 
bottles   are   available  
from CITROËN dealers, until they are
equipped

with AdBlue
® delivery pumps.
If
 
you
 
want
 
to
 
fill
 
the
 
AdBlue® tank yourself, ensure that you have a
suitable
 
filler
 
pipe,
 
which
 
may   or   may  
not be supplied with the additive
container

.
CHECKS
7
AdBlue®

166
Berlingo2VP_en_Chap07_Verification_ed02-2016Berlingo2VP_en_Chap07_Verification_ed02-2016
Range indicators
Rules on the display of alertsFor more information on the
displays and warning lamps, refer
to chapter 3, "Instruments and
controls"
  section. Range greater than 1 500 miles
(2 400 km)
No
  information   displayed.
Once   the   1   500   miles   (2   400   km)  
threshold is reached, the UREA


warning lamp comes on temporarily
and the remaining range message is
displayed.
The alert is repeated every 200 miles
(300
  km)   until   the   next   threshold   is  
reached.
Every time the ignition is switched
on, the alert is given, together with an
audible

  signal.
Remaining range less than
1
500 miles (2 400 km) and greater
than 350 miles (600 km)
Driving range
With
  the   touch   screen   tablet:
If the range is greater than 3 100 miles
(5
  000   km),   a   range   value   is   not   given.
Press this button to display
the
  information.
-

select the "Driving
assistance" menu,
-


select "Diagnostic",
-

 
select
  CHECK.
Different levels of alert are triggered
according to the remaining driving
range threshold
You will be informed as each mileage
threshold is reached and the alerts will
change
  from   temporary   to   permanent.
-

The 1st is triggered at a remaining
driving range of 1 500 miles
(2
 
400
  km).
-

The 2nd is triggered at a remaining
driving range of 350 miles
(600
 
km).
-

Up to 0 miles, at which point it will
be impossible to restart the engine
after

 
a
 
stop.
AdBlue®

 167
Berlingo2VP_en_Chap07_Verification_ed02-2016Berlingo2VP_en_Chap07_Verification_ed02-2016
Once the 350 miles (600 km) threshold is reached, the UREA warning lamp
flashes
  and   the   Service   warning   lamp  
comes on, accompanied by a message
on

  the   remaining   driving   range.
The alert is repeated every 30 seconds
with an update of the remaining driving
range
  in   steps   of   30   miles   (50   km)  
travelled.
Every time the ignition is switched
on, the alert is given together with an
audible

  signal.
At 0 miles the system installed in
the vehicle to meet the emissions
standard will prevent engine
starting. Your vehicle's exhaust emissions no
longer meet the "Euro 6" standard and
the
  engine   will   not   start.
To be able to restart the vehicle, you
must add at least 4 litres of AdBlue
®.
-
 
Pour

 
the
 
additive
 
into
 
the
 
tank
 
(by  
the

 
filler
 
with
 
the
 
blue
 
cap).
-

Switch on the ignition without
starting.
-


W

ait 10 seconds before starting the
engine.
Remaining range less than 350 miles
(600 km) and more than 0 miles
Starting prevented, breakdown related
to a lack of AdBlue
®
in the special tank
The
 
0
 
fluid
 
level
 
has   been   reached.
Avoid waiting until the
remaining range is 0 miles!
The alert is repeated when driving until
the AdBlue
® tank has been topped-up with
 
sufficient   additive.
Unless the additive in the special
additive
 
tank   is   topped-up,   you   risk  
immobilisation

  of   the   vehicle. Following
  this,   make   a   further   fill  to
  the   special   additive   tank,   the  
capacity of which is

17 litres.
Fault with the SCR system
The UREA, Service and diagnostic
warning  lamps   comes   on.
Every time the ignition is switched on,
the
  emissions   fault   is   confirmed   by   an  
audible

  signal   and   a   message.
If it is a temporary fault, the alert
disappears as soon as the exhaust
emissions return to the levels required
by
  the   standard.
Detection
On the other hand, if the warning
lamps are still on after 30 miles
(50   km)   of   driving,   the   fault   is  
confirmed.
An engine start prevention system
will be activated automatically after
650 miles

  (1   100   km)   travelled  
following

  this   confirmation.
Go
  to   a   CITROËN   dealer   or   a   qualified  
workshop.
Or go to a CITROËN dealer or a
qualified

 
workshop.
CHECKS
7
AdBlue®

168
Berlingo2VP_en_Chap07_Verification_ed02-2016Berlingo2VP_en_Chap07_Verification_ed02-2016
Fault confirmed
In addition to the previous signals,
the  UREA
 
warning   lamp   flashes   and  
the remaining range allowed will be
displayed

  in   miles   (kilometres).
The alert will be repeated every
30
seconds with an update of the
driving range in steps of 30 miles
(50 km).
Go
  to   a   CITROËN   dealer   or   a   qualified  
workshop

  as   soon   as   possible.
You
  risk   not   being   able   to   start   the  
engine.
Starting prevented, having
covered the 650 miles (1 100 km)
At each attempt at starting, the alert is
activated and the message "Emissions
fault:

  Starting   prevented"   is   displayed.Refilling / Topping-up the
AdBlue®
Precautions to take
Use only AdBlue ® that meets the
ISO
 
22241
 
standard.
The AdBlue
® fluid is an urea-based solution.
This
 
fluid
 
is
 
non-flammable,   colourless  
and

 
odourless.
To
 
be
 
kept
 
in
  a   cool   area.
Containers (5 or 10 litres) and
bottles (1.89 litres) of AdBlue
®
Please check the use-by date.
Read   the   instructions   on   the   label.
Ensure that you have a suitable
filler
  pipe,   which   may   or   may   not   be  
supplied

  with   the   container. In
  the   event   of   an   overflow,   wipe  
around

  the   filler   mouth   using   a  
damp

  cloth.
If any AdBlue
® fluid is split or splashed on to you, wash immediately with cold
water or wipe yourself with a clean
damp
 
cloth.
If
 
the
 
fluid
 
has
  crystallised,   clean   it   off  
using

 
a
 
sponge   and   hot   water.
To
 
facilitate   filling,   an   adaptor   is  
available

 
from   CITROËN   dealers.
AdBlue®

169
Berlingo2VP_en_Chap07_Verification_ed02-2016Berlingo2VP_en_Chap07_Verification_ed02-2016
Filling
Ensure that the vehicle is parked on a flat  and   level   surface.
Pour
  the   contents   of   the   container   /  
bottle

  into   the   dedicated   tank.
After
  filling   the  
AdBlue® tank, observe the
 
following
 
procedure:
-

Switch on the ignition without
starting.
-


W

ait 10 seconds before starting the
engine.
Never dispose of empty AdBlue
®
containers and bottles in the
household
 
waste.
Place them in a special container
provided
 
this
 
purpose
 
or
 
take
 
them
 
to  
your

 
dealer. Keep AdBlue
® out of the
reach of children, in its original
container.
Never transfer AdBlue
® to another
container:
 
it
 
would
 
loose   its   purity.
Never
 
dilute
 
the
 
fluid
 
with   water.
Never
 
pour
 
the
 
fluid
 
into   the   Diesel   fuel  
tank.
Recommendations on storage
Never store containers or bottles of
AdBlue® in your vehicle.
Freezing of the AdBlue
®
AdBlue® freezes at about -11°C (12.2° F) and
 
deteriorates   above   25°C   (77°F).
It is recommended that containers and
bottles be stored in a cool area and
protected
  from   direct   sunlight.
Under
 
these   conditions,   the   fluid   can  
be

 
kept
  for   at   least   a   year.
Additive that has been frozen can
be used once it has thawed out in
ambient air. The SCR system includes an
AdBlue
® tank heater that ensures operation of the vehicle in normal
conditions.
In exceptional situations, such as when
the
 
vehicle
 
is   kept   at   temperatures  
below -15°C (5°F) for a long period,
there may be an emission fault alert
related to freezing of the

AdBlue
®
additive.
Park
 
the
 
vehicle
 
in
 
an
 
area
 
at
 
a
 
more  
moderate temperature for a few hours
until

the AdBlue
® becomes a fluid again.
The emissions warning lamp does not
go of
f immediately, but does so after a
few
 
miles
 
of
 
driving.
CHECKS
7
AdBlue®

171
Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016
ECONOMY MODE
After the engine has stopped, with
the
  key   in   the   ignition   position,   certain  
functions (windscreen wiper

, electric
windows, courtesy lamps, audio
equipment,
  etc.)   can   only   be   used   for   a  
cumulative duration of thirty minutes, to
prevent

  discharging   of   the   battery.
Once the thirty minutes have elapsed,
the active functions are put on standby
and
  the   battery   warning   lamp   flashes  
accompanied by a message in the
screen.
T

o resume the use of these functions
immediately, start the engine and let it
run
  for   a   few   minutes.
The time available will then be double
the time for which the engine was left
running.
  However,   this   time   will   always  
be

  between   five   and   thirty   minutes.
A
 

flat   battery   will   prevent   the  
engine

  from   starting.
Battery
QUICK HELP
8