2017 Citroen BERLINGO MULTISPACE RHD steering

52
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Acceleration
For optimum acceleration (e.g. to overtake  another   vehicle),   simply  
press the pedal beyond the point of
resistance at the end of its travel, by
pressing

  down   firmly.
Vehicle stationary, with the
engine running
In the event of a prolonged stop with
the engine running, the gearbox
changes automatically to neutral N.
Stopping the vehicle
Before stopping the engine, put the
gear selector in position N.
In all cases, it is essential to apply
the  parking   brake.   Check   that   the  
parking

  brake   warning   lamp   is   on   in   the  
instrument

  panel.
Before doing anything in the
engine
  compartment,   check   that  
the gear selector is in neutral

N.
Changing gear
In situations of high engine speeds
(heavy acceleration), a change
up will not occur unless the driver
operates the electronic gearbox control
paddle. Pull on the "+" control
paddle
  to   change   up.
Pull on the "-" control
paddle to change
down.
-

If the vehicle stops or reduces
speed (for example when
approaching a stop sign),
the gearbox changes down
automatically

,   to   first   gear   if  
needed.
-


It is not necessary to release the
accelerator completely during gear
changes.
-


A
gear change instruction is
accepted only if the engine speed
permits.
-

For safety reasons, depending on
the engine speed, a change down
may

  be   performed   automatically.
Manual mode
Changing to manual mode
Move the gear selector to M. Automatic mode Changing to automatic
mode
Move the gear selector to A.
The gearbox then operates in
automatic mode, without any action on
your
 
part.
It constantly selects the gear that is
best
 
suited
 
to
 
the
 
following
 
conditions:
-

driving style,
-

 
road

 
profile,
-
 
optimum

 
fuel
 
consumption.
Gearbox and steering wheel

53
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
STOP & START
The Stop & Start system puts the
engine temporarily on standby - ST OP
mode
  -   during   stops   in   the   traffic   (red  
lights,

  traffic   jams,   or   other...).
The engine restarts automatically -
START mode - as soon as you want to
move
  off.
The
  restart   takes   place   instantly,  
quickly

  and   silently.
Perfect for urban use, the Stop & Start
system reduces fuel consumption and
exhaust emissions as well as the noise
level
  when   stationary.
Operation
Going into engine STOP modeThe "ECO" warning lamp
comes on in the instrument
panel and the engine goes
into
  standby:
-

with a manual gearbox
, at speeds
below
  12   mph   (20   km/h),   when   you  
put the gear lever into neutral and
release the clutch pedal,
-


with a 6-speed electronic
gearbox

, at speeds below 5 mph
(8
  km/h),   when   you   press   the   brake  
pedal or put the gear lever into
position

N. If
  your   vehicle   is   fitted   with   the   system,  
a time counter calculates the sum of
the periods in ST

OP mode during a
journey.   It   rests   itself   to   zero   every   time  
the

  ignition   is   switched   on   with   the   key.
With a 6-speed electronic
gearbox, for your comfort during
parking   manoeuvres,   STOP
 
mode  
is not available for a few seconds after
coming

  out   of   reverse   gear.
STOP mode does not affect the
functionality of the vehicle, such as
braking,   power   steering,   for   example.
Never refuel with the engine in
STOP mode; you must switch off
the   ignition   with   the   key.Special cases: STOP mode
unavailable
STOP
 

mode   is   not   invoked   when:
-
the vehicle is on a steep slope
(rising or fallin

g),
-
the driver's door is open,
-

the driver's seat belt is not
fastened,
-

the vehicle has not exceeded

6   mph   (10   km/h)   since   the   last  
engine

  start   using   the   key,
-
the engine is needed to maintain
a comfortable temperature in the
passenger compartment,
-

demisting is on,
-

some special conditions (battery
charge, engine temperature,
braking

  assistance,   ambient  temperature...)
  where   the   engine  is needed to assure control of a
system.
In this case, the
"ECO"
warning
  lamp   flashes   for   a  
few

  seconds,   then   goes   off.
This operation is perfectly normal.
READY TO GO
3
Stop & Start

55
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
The Stop & Start system
requires  a   battery   of   specific  
characteristics.

 
All
  work   on   this  
type of battery must be done only
by

 
a
  CITROËN   dealer   or   a   qualified  
workshop.
For more information on the 12 V
battery

,   refer   to   "Battery"   in   section   8.
Good practice when stopping Good practice when starting
Diesel pre-heating warning
lamp
If the temperature is high
enough, the warning lamp
comes on for less than
one second, you can start
without
  waiting.
In cold weather, wait for this warning
lamp to go off then operate the starter
(Starting position) until the engine
starts. Door or bonnet open
warning lamp
If this comes on, a door or the bonnet
is
  not   closed   correctly,   check!
Minimise engine and gearbox wear
When switching off the ignition, let the
engine run for a few seconds to allow
the turbocharger (Diesel engine) to
return
  to   idle.
Do not press the accelerator when
switching
  off   the   ignition.
There is no need to engage a gear
after
  parking   the   vehicle.
STARTING AND ST OPPING
Running and accessories position.
To
  unlock   the   steering,   turn   the  
steering wheel gently while turning the
key

,   without   forcing.   In   this   position,  
certain

  accessories   can   be   used.
Starting position.
The starter is operated, the engine
turns
  over,   release   the   key.
STOP position:
  steering   lock.
The
  ignition   is   off.  
T
urn   the   steering  
wheel

  until   the   steering   locks.   Remove  
the

  key.
Opening the bonnet
Before doing anything under the
bonnet, deactivate the Stop & Start
system
 
to
 
avoid
 
the
 
risk
 
of
 
injury
 
related to an automatic change to
ST

ART
 

mode.
Driving on flooded roads
Before
 
driving
 
through
 
a
 
flooded
 
road,
 
it is strongly recommended that you
deactivate

 
the
 
Stop
 
&
 
Start
 
system.
For more advice on driving, particularly
on
 
flooded
 
roads,
 
refer
 
to
 
the
 
corresponding

 
section.
READY TO GO
3
Stop & Start

58
Berlingo2VP_en_Chap04_Ergonomie_ed02-2016
DIRECTION INDICATORS
"Motorway" function
Press  the   control   up   or   down   to   flash  
the corresponding direction indicator
three

  times.
LIGHTING
Left: downwards passing the point  of   resistance.
Right:
  upwards   passing   the  
point

  of   resistance.
Front and rear lighting
Lighting off
Automatic illumination of
headlamps
Sidelamps
Dipped beam (green)
Dipped beam/main beam change
Pull
 
the
 
stalk   fully   towards   you.
Lighting-on audible warning
On switching off the ignition, all of the
lamps turn off, except dipped beam if
automatic guide-me-home lighting has
been
 
activated.
 Checking

 
by
 
means
 
of
 
the
 
indicator
 lamps in the instrument panel is


described in the "Instruments and
controls"
 
section
 
of
 
chapter
 
3.
Direction indicators
Selection is by turning this
ring. Main beam (blue)
To activate the lighting
control, turn this ring to
the lighting off position "0"
then to the selection of
your   choice.
On opening the driver's door, there is
an audible warning if you have left the
lighting
  on.
Steering mounted controls

59
Berlingo2VP_en_Chap04_Ergonomie_ed02-2016
LED DAYTIME RUNNING LAMPS
Rear foglamps (amber,
2nd rotation of the ring
forwards).
Front foglamps (green,
1st
rotation of the ring
forwards). Rotate this ring forwards
to switch on and
rearwards   to   switch   off.
Their   state   is   confirmed   by  
the warning lamps in the
instrument

  panel. Do not forget to switch them off
when   they   are   no   longer   needed.
Operation of the automatic illumination
of headlamps switches off the rear
foglamps, but the front foglamps
remain   on.
To switch off the front and
rear foglamps, turn the
ring rearwards twice in
succession.
Automatic illumination of headlamps
In foggy weather or in snow,
the sunshine sensor may detect
sufficient   light.
As a consequence, the lighting
will
  not   come   on   automatically.   If  
necessary

, you must switch on
the dipped
  beam   headlamps   manually.
Do not cover the sunshine sensor
located on the windscreen, behind
the
 
mirror.   It   is   used   for   the   automatic  
illu

mination of headlamps and for the
automatic
  rain   sensitive   wipers.
Activation The sidelamps
and dipped beam
headlamps switch
on automatically if
the light is poor, or
during operation of the windscreen
wipers.  
They
  switch   off   as   soon   as   the  
light becomes bright enough or the
windscreen

  wipers   stop.
On starting the vehicle, in daylight the
LED daytime running lamps come on
automatically.
If the sidelamps and headlamps are
switched on manually or automatically,
the
 
daytime
 
running
 
lamps
 
go
 
off.
Programming
For countries where exterior lighting by
day is not a legal requirement, you can
activate or deactivate the function via
the   configuration   menu.
If the user does not operate any
equipment for 30 minutes, the
Economy mode engages to avoid
discharging
 
the
 
battery.
 
Electrical
 
functions are put on standby and the
battery

 
warning
 
lamp
 
flashes.
Sidelamp operation is not affected by
Economy
 
mode.
In clear weather or in rain, both day
and night, rear foglamps dazzle and
their  use   is   prohibited.
Refer to chapter 8, "Battery
section".
Front and rear foglamps
They operate with the sidelamps and
dipped
 
beam
 
headlamps.
Turn the ring to the AUTO  position.  The activation of this function is
accompanied by a message in the
screen.
Deactivation
T
urn   the   ring   forwards   or   rearwards.  
The deactivation of this function is
accompanied by a message in the
screen. This function is not compatible with
daytime
  running   lamps.
Steering mounted controls
EASE OF USE and COMFORT
4

60
Berlingo2VP_en_Chap04_Ergonomie_ed02-2016
If the sunshine sensor
does not function correctly,
the lighting comes on
accompanied by the service
warning lamp, an audible
signal
 
and   a   message   in   the   screen.
Contact a CITROËN dealer or a
qualified
  workshop.
Guide-me-home lighting
Keeping the dipped beam headlamps
on temporarily with the ignition off,
makes   the   driver's   exit   easier   when   the  
light

  is   poor.
HEADLAMP BEAM
The beam setting must be adjusted to suit
  the   load   in   the   vehicle.
0 -
  No   load.
1 -
  Partial   load.
2 -
 
A
verage   load.
3 -
  Maximum   authorised   load.
Manual operation
-
 
With

 
the
 
ignition
 
off,
 
"flash"
 
the
 
headlamps within one minute after
switching

 
off
 
the
 
ignition.
The guide-me-home lighting switches
off
 
automatically
 
after
 
a
 
set
 
time.
Automatic operation
Refer to chapter 10, "Screen
menu
 
map"
 
section. Initial setting is position 0.
Activate the function via the
vehicle
 
configuration
 
menu. Programming
The system is activated or deactivated
in
 
the
 
vehicle
 
configuration
 
menu.
The
 
system
 
is
 
activated
 
by
 
default.
Switching off
The
 
system
 
does
 
not
 
operate:
-

below a certain angle of rotation of
the steering wheel,
-

 
above

 
25
 
mph
 
(40
 
km/h),
-
 
when

 
reverse
 
gear
 
is
 
engaged.
Switching on
This
 
function
 
starts:
-

when the corresponding direction
indicator is switched on,
or
-


from a certain angle of rotation of
the

 
steering
 
wheel.
With dipped or main beam headlamps,
this
 
function
 
makes
 
use
 
of
 
the
 
beam
 
from a front foglamp to illu

minate the
inside of a bend, when the vehicle
speed is below 25 mph (approximately
40
 
km/h)
 
(urban
 
driving,
 
winding
 
road,
 
intersections,

 
parking
 
manoeuvres...).
CORNERING LIGHTING
Travelling abroad
If using your vehicle in a country
that drives on the other side of the
road,
  the   headlamps   must   be   adjusted  
to

 
avoid   dazzling   on-coming   drivers.
Contact a CITROËN dealer or a
qualified
  workshop.
The function is deactivated temporarily
when you use the manual lighting
control
 
stalk.
Steering mounted controls

61
Berlingo2VP_en_Chap04_Ergonomie_ed02-2016
2 Fast  wipe   (heavy   rain).
1  
Normal
  wipe   (moderate   rain).
l
 
Intermittent
  wipe.
0
 
Of
f.
â

Single wipe
 (press

  downwards).
In the Intermittent position, the wiping
speed is in proportion to the vehicle
speed.
WIPERS
Manual wipingWhenever the ignition has been
switched off for more than one minute,
with
  the   windscreen   wiper   stalk   in  
position

  2,   1   or   I,   the   stalk   must   be  
reactivated.
-

 
Move
  the   stalk   to   any   position.
-
 
Return
  it   to   the   desired   position.
Do not cover the rain sensor,
located in the centre of the
windscreen,
  behind   the   mirror.Activation
Press
  the   control   downwards.  
Activation of the function is
accompanied by a message in the
screen.
Deactivation
Place

  the   windscreen   wipers   stalk   in  
position

I, 1 or 2.
Deactivation of the function is
accompanied by a message in the
screen.
In the event of malfunction of the
automatic windscreen wipers, the
windscreen wipers will operate in
intermittent
  mode.
Contact a CITROËN dealer or a
qualified
  workshop   to   have   the   system  
checked. In the
AUTO position, the windscreen
wipers operate automatically and
adapt their speed to the intensity of the
rainfall.
When not in AUTO mode, for the
other positions, refer to the manual
windscreen   wipers   section.
The automatic rain sensitive
windscreen wipers function must
be   reactivated   by   pressing   the   stalk  
downwards, if the ignition has been
switched

  off   for   more   than   one   minute.
When using an automatic car
wash, switch off the ignition to
avoid triggering the automatic
wiping.
In winter, it is advisable to wait for the
windscreen to completely clear of ice
before
  operating   the   automatic   wipers.
Automatic wipers
Steering mounted controls
EASE OF USE and COMFORT
4

62
Berlingo2VP_en_Chap04_Ergonomie_ed02-2016
Screenwash
Pull the stalk towards you, the wash-
wipe is accompanied by a timed sweep
of
  the   wipers.
Turn
  the   ring   past   the   first  
position:

  the   rear   screenwash  
then the rear wiper operates
for

  a   fixed   time.
In winter, in the event of a
considerable amount of snow
or ice, switch on the heated
rear
  screen.   Once   the   screen   is  
clear

, remove the snow or ice which
has accumulated on the rear wiper
blade.
 
Y
ou   can   then   operate   the   rear  
windscreen

  wiper.
To top up the level, refer to the
"Levels"
  section   of   chapter   7.
Special position of the
windscreen wipers
In the minute following switching
off of the ignition, any action on the
stalk  positions   the   wipers   against   the  
windscreen

  uprights.
This action enables you to position
the
  wiper   blades   for   winter   parking,  
cleaning

  or   replacement.
Refer to the "Changing a windscreen
wiper
  blade"   section   of   chapter   8.
To
  park   the   wipers   in   their   normal  
position after this has been done,
switch on the ignition and move the
stalk. T

urn   the   ring   to   the   first  
position.
Rear wiperRear screenwash
Steering mounted controls