2017 Citroen BERLINGO MULTISPACE RHD steering

172
Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016
The temporary tyre repair kit consists of a compressor and a bottle
(containing  a   sealant).
Using the kit
- Tick  the   deflated   wheel   on   the  speed
  limitation   sticker   then   affix  
the

  sticker   to   the   vehicle's   steering  
wheel to remind you that a wheel is
in

  temporary   use.
-

Clip the bottle
1 on the
compressor
2.
-

Connect the bottle
1 to the valve of
the
  tyre   to   be   repaired.
-
 
T
ake   care   to   unwind   the  
compressor pipe before connecting
it

  to   the   bottle.
-

Connect the power lead to one of
the

  vehicle's   12V   sockets.
-

Switch on the compressor by
pressing button

A until the tyre
pressure
  reaches   2.0   bars.   If   this  
pressure cannot be reached, the
tyre

  cannot   be   repaired.
-
 
Remove
  and   store   the   compressor.
-

Drive immediately
, for a few miles
(kilometres),
  at   reduced   speed,   to  
fill

  the   puncture.
-
 
Adjust
  the   pressure   using   the  
compressor in accordance with the
recommendation for the vehicle and
check

  that   the   leak   is   filled   correctly  
(no

  further   loss   of   pressure).
-

Drive at reduced speed (50
mph
[80
  km/h]).  
The
  tyre   must   be  
examined and repaired by a
specialist

  as   soon   as   possible.After use, the bottle can be stored in
a
  plastic   bag,   supplied   in   the   kit,   to  avoid staining your vehicle with traces
of
  fluid.
Warning:
  the   sealant   product   is  
harmful if swallowed and causes
irritation

  to   the   eyes.
Keep
  it   out   of   reach   of   children.
After use, do not discard the bottle into
the
  environment,   take   it   to   a   CITROËN  
dealer or to an specialised waste
disposal

  site.
Replacement bottles of sealant are
available
  from   CITROËN   dealers.
TEMPORARY PUNCTURE
REP

AIR KIT
The kit is located in one of the two storage compartments located
under
  the   front   seats.
Vehicles supplied with a temporary
puncture
  repair   kit   do   not   have   a   spare  
wheel

  or   tooling   (jack,   wheelbrace, ...).
Changing a wheel

190
Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016
Fuses under the bonnet
After opening the bonnet, unclip and tilt
the corresponding box to gain access
to  the   fuses. Fuses
F Amperes
A Allocation
1 20 Engine management
2 15 Horn
3 10 Front and rear wash-wipe pump
4 - Not used
5 15 Engine components
6 10 Steering wheel angle sensor, DSC
7 10Brake
  switch,   clutch   switch
8 25 Starter motor
9 10 Headlamp
  beam   motor,   fleet   management   unit
10 30 Engine components 11 40 Not used
12 30 Wipers
13 40 Built-in systems interface
14 30 Pump
15 10 Right-hand main beam headlamp
16 10 Left-hand main beam headlamp
17 15 Right-hand dipped beam headlamp
18 15 Left-hand dipped beam headlamp
Changing a fuse

192
Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016
Without lifting (4 wheels on the
road)
You should always use a towing arm.
BEING TOWED
This procedure involves the use of
the towing eye supplied with the tools
for
  changing   a   wheel.
From the front
- Unclip the cover by pressing the
bottom  part.
-

Fully screw in the removable
towing eye.
From the rear
- Unclip the cover using a coin or the
flat   part   of   the   towing   eye,
-

Fully screw in the removable
towing eye. When towing with the engine
switched

  off,   there   is   no   braking   or  
steering

  assistance.
Lifting (only 2 wheels on the
road)
It is preferable to raise the vehicle
using
  professional   lifting   equipment.Vehicles fitted with a manual
gearbox (Diesel version)
In
  the   case   of   vehicles   fitted   with  
a manual gearbox, the gear lever
must be in neutral, failure to observe
this special condition may result in
damage

  to   transmission   and   braking  
components and the absence of
braking

  assistance   when   the   engine   is  
started

  again.
Section
 
8,
 
"Changing
 
a
 
wheel".
Having your vehicle towed

203
Berlingo2VP_en_Chap10a_SMEGplus_ed02-2016
7-inch touch screen tablet
GPS satellite navigation - Multimedia audio - Bluetooth® telephone
Contents
First steps
2 04
Steering mounted controls
20

6
Menus
 2

07
Navigation


208
Navigation - Guidance
2

16
Traffic
 2

20
Radio Media

2
22
Radio

2
28
DAB (Digital Audio Broadcasting) radio

2
30
Media
2

32
Settings


234
Connected services
2

42
MirrorLink
TM 2 42
CarPlay® 246
T
elephone
2
48
Frequently
  asked   questions  
2
56
The system is protected in such a way that it will only operate in
your
 
vehicle. As a safety measure, the driver should only carry out operations
which
 
require
 
prolonged
 
attention   while   the   vehicle   is   stationary.
The display of an energy economy mode message signals that
electrical
 
systems
 
operating
 
are   going   into   standby.
Refer
 
to
 
the
 
energy
 
economy   mode   section.
Audio and Telematics
TECHNOLOGY on BOARD
10

206
Berlingo2VP_en_Chap10a_SMEGplus_ed02-2016
Steering mounted controls
Radio: select the previous/next preset s tation.
Media:
  select   a   genre   /   artist   /   folder  
f

rom   the   list.
Select
  the   previous/next   entry   in  
a m

enu.
Decrease
  volume.
Radio:
  automatic   search   for   a   higher  
f

requency.
Media:
  Select   next   track.
Media,
  press   and   hold:   fast   for ward.
Jump
  in   the   list. Mute:
  cut   the   sound   by   pressing  
t

he volume increase and decrease
buttons
 s

imultaneously.
Restore the sound by pressing one of
the
  two   volume   buttons.
Radio:
  automatic   search   for   a   lower  f
requency.
Media:
  select   previous   track.
Media,
  press   and   hold:   fast   back.
Jump
  in   the   list.
Change
  the   audio   source.
Confirm
  a   selection.
Call/end
  call   on   the   telephone.
Press
  for   more   than   2   seconds:  
a

ccess   to   the   telephone   menu. Increase
  volume.
Audio and Telematics

232
Berlingo2VP_en_Chap10a_SMEGplus_ed02-2016
The audio system will only play audio files
with  ".wma,   .aac,   .flac,   .ogg   and   .mp3"   file  
e

xtensions and with a bit rate of between
32 Kbps
  and   320   Kbps.
It
  also   supports   VBR   (Variable   Bit   Rate)   mode.
No
  other   type   of   file   (.mp4,   ...)   can   be   played.
".wma"
  files   must   be   of   the   standard   wma   9   type.
The sampling rates supported are 32, 44 and
48
  KHz.
Information and advice
Media
USB port
Selection of source
The steering mounted SRC (s o u r c e)
button can be used to go to the next
media source, available if the source
is
  active.
Select
 
change
 
of
 
source.
Press on Radio Media
to display the
primary
 pag

e.
The system builds playlists (in temporary
memory),
 
an
 
operation
 
which
 
can
 
take
 
from
 
a f

ew seconds to several minutes at the first
connection.
Reduce the number of non-music files and the
number
 
of
 
folders
 
to
 
reduce
 
the
 
waiting
 
time.
The playlists are updated every time the
ignition is switched off or on connection of a
USB
 
memory
 
stick.
 
The
 
lists
 
are
 
memorised:
 
if
 
t

hey are not modified, the subsequent loading
time
 
will
 
be
 
shorter.
Insert
 
the
 
USB
 
memory
 
stick
 
into
 
the
 
USB
 
port
 o
r connect the USB device to the USB port
using
 
a
 
suitable
 
cable
 
(not
 
supplied).
Auxiliary socket (AUx)
Connect the portable device (MP3 player…) to
the   auxiliary   Jack   socket   using   an   audio   cable  
(

not
 sup
plied).
This source is only available if the "Auxiliary
socket"
  option   has   been   activated   in   the  
"

Media"   settings.
First   adjust   the   volume   of   your   portable   device  
(

to   a   high   level).   Then   adjust   the   volume   of   your  
a

udio   system.
Display and management of the controls are
via
  the   portable   device. Choose
  the   source.
To protect the system, do not use a
USB
 
hub.
Audio and Telematics

254
Berlingo2VP_en_Chap10a_SMEGplus_ed02-2016
Managing paired
telephones
This function allows the connection or
disconnection of a peripheral device as
well  as   the   deletion   of   a   pairing. Using the telephone is not
recommended
  while   driving.
Park
  the   vehicle.
Make
  the   call   using   the   steering  
m

ounted   controls.
Press on Telephone
to display the
primary
 pag

e.
Press
  on   the   secondary   page.
Select " Bluetooth " to display the list
of
  paired   peripheral   devices.
Select
  the   peripheral   in   the   list.
Select " Search for devices "
Or "Connect / Disconnect " to start or
end the Bluetooth connection with
the
  selected   device.
Or "Delete "
  to   delete   the   pairing.
Receiving a call
An incoming call is announced by a ring and a
superimposed  display   in   the   screen.
Make
  a   short   press   on   the   steering  
m

ounted TEL button to accept an
incoming
 c

all.
Make
  a   long   press
on the steering mounted TEL button
to
  reject   the   call.
Or Select "End call".
Making a call
Calling a new number
Press on Telephone to display the
primary pag e.
Enter the phone number using the
digital
 k

eypad.
Press " Call"
  to   start   the   call.
Calling a contact
Press on Telephone to display the
primary pag e.
Or
  make   a   long   press
on the steering mounted TEL
 

button.
Audio and Telematics

265
Berlingo2VP_en_Chap10b_RD45_ed02-2016
Audio system
Audio system / Bluetooth®
Contents
First steps
2 66
Steering
 
mounted
 
controls
 
2
67
Menus
268
Radio
268
Media
 2

70
Telephone
 2

74
Screen
 
menu
 
map(s)
 
2
76
Frequently
 
asked
 
questions
 
2
80
Your Audio system is coded in such a way that it will only operate
in
 
your
 
vehicle. As a safety measure, the driver must only carry out operations
which
 
require
 
prolonged
 
attention
 
while
 
the
 
vehicle
 
is
 
stationary.
When the engine is switched off and to prevent discharging of the
battery,
 
the
 
audio
 
equipment
 
may
 
switch
 
off
 
after
 
a
 
few
 
minutes.
Audio and Telematics
TECHNOLOGY on BOARD
10