2017 AUDI TT COUPE oil level

Instrumen ts and ind icator ligh ts
Instruments and indicator Lights
Instruments
Audi virtual cockpit (instrument cluster)
The instrument cluster is the central information center for the driver.
Fig. 3 Instrume nt cluster overv iew
(D Eng ine coolant temperature 8
@ Driver information system . . . . . . 19
® Fuel level . . . . . . . . . . . . . . . . . . . . 8
@ Trip odometer reset knob . . . . . . . 23
Coolant temperature indicator
The coolan t temperature display c:> page 8,
fig. 3
(D only functions when the ignition is
switched on. To prevent engine damage, p lease
observe the following notes about the tempera­
ture ranges.
Cold rang e
If o nly the L EDs in the left area of the gauge turn
on, the engine has not reached operating tem­
perature yet. Avoid high engine speeds, full ac­
celerating and heavy engine loads .
Normal range
The engine has reached its operating tempera­
ture once the LEDs up to the center of the gauge
turn on . If the . indicator light in the Infotain­
ment system display turns on, the coolant tem­
perature is too high
c:> page 12.
8
(D Note
-Aux iliary head lights and other accessories in
front of the coo ling-a ir intake impa ir the
cooling effect o f the coolant. This increases
the risk of the engine overheating during high outside temperatures and heavy en ­
gine load.
- T he front spoiler a lso helps to distribute
cooling air correctly while driving . If the
spoiler is damaged, the cooling effect will
be impaired and the risk of the eng ine over­
heating w ill increase. See an authorized
Audi dealer or author ized Audi Service Fa­
cility for assistance .
Fuel level
The indicator @ only func tions when the ignition
i s sw itched on. If the fuel level drops below 1.9
gal (7
L), a red LED wi ll light up and the rD indi­
cator light will turn on
c:> page 16 . The LED
blinks red when the fuel level is very low.
The fuel tank capacity of your veh icle is listed in
the
Techni cal Dat a sectio n c:> page 299. ..,_

Instruments and indicator lights
Engine control
c::> page 15
Emi ssions control system
c::> page 15
Engine speed limitat io n
c::> page 15
Engine oil level
c::> page 15
Engine oil senso r
c::> page 16
Battery charge
c::> page 13
Tank system
c::> page 16
Washer fluid level
c::> page 16
W indshield wipe rs
c::> page 16
Remote control key
c::> page 58
Battery in remote control key
c::> page 27
Bulb failure ind icator *
c::> page 16
Headlight range control system
c::> page 17
Adaptive light*
c::> page 17
- Light/
rain sensor*
• c::> page 17
Transmiss ion
c::> page 68 0
. . I I
~-e ... , . , ,.
I .
©-e .... , .. ,
&
Central indicator light
c::> page 14
@!
Electromechan ical steer ing./
c::> page 91
;
Adapt ive dampers*
c::> page 17
10
Rear spoiler
c::> page 92
Other indicator lights
- T
ur n signals
Ii ii c::> page 17
y>))
D
Rea r safety be lt./
c::> page 13
USA mod els : cru ise cont rol system*
c::> page 70
C anada models : cruise control sys ­
tem *
c::> page 70
Active lane assist*
c::> page 73
Conven ience key
c::> page 59
Electromechanica l park ing brake
c::> page 11
Active lane assist*
¢ page 73
Audi side assist *
c::>page 78
Transm iss io n
c::> page 68
Electromechan ica l park ing brake
c::> page 11
Rear safety belt./
c::> page 13
Rear safety belt./
c::> page 13
USA models: speed warn ing sys­
tem"
c::> page 70
Canada models: speed warn ing sys­
tem*
c::> page 70
High beams
<=:> page 37
BRAKE /{(JJ) Brak e sys te m
If this indicato r light turns on, there is a malfunc-
tion in the b rake system .
.,.

Instruments and indicator lights
To release the parking brake, press the bra ke
pedal and p ress th e ~ button at the same time,
or start driv ing with h ill start ass ist
c::> pag e 61,
S tarting from a s top.
1ij Parking brake: malfunction! See owner's
manual
T here is a malfunc tion in the park ing b rake. Dr ive
to an a uthor ized Audi dealer or au thor ized A udi
Serv ice Facility immediately to have the mal func ­
tion cor rected.
Ii.I Parking brake: malfunction! Safely stop ve ·
hicle. Please contact Service
There is a malfunc tion in the park ing brake . Dr ive
to an author ized Audi dealer or author ized A udi
S erv ice Fa cil ity immedi ately to have t he m alfunc­
tion correc ted .
IB;J:t:);JJJ~ (USA models ) / Ii] (Canada models)
Please release parking brake.
Re lease the par king brake if t his message ap­
pea rs .
11;1;!:t :);tJJ~ (USA models ) 111] (Canada models )
Parking brake auto release unavailable
If th is message appears, press the brake pedal
fi rst an d then re lease the pa rking bra ke .
ltl;!:t:);tJ:OusA models) / Ii] (Canada models)
Parking brake: caution! Vehicle parked too
steep
If th e i ndic ator lig ht blinks and t he m es sage ap ­
pe ars, the re is not eno ugh br aking power to se­
cure the vehicle . The bra kes have overheated. The
ve hicle co uld roll away eve n on a small incline .
ltl;!:t:);JJJ~ (USA models) t Ii] (Canada models)
Parking brake is applied
If t his message appears, press the bra ke pedal
f ir st a nd the n release the pa rk ing bra ke if neces ­
sa ry.
@ Tips
For add it iona l information on the park ing
bra ke, see
c::, page 60.
12
_L Cooling system
• Turn off engine and check coolant level
The coolant level is too low .
Do not continue dr iv ing and switch the en gine
off. Check the coolant level
c::, page 250 .
-If the coo lant level is too low, add coolant
c::, page 2 50. Only continue driving once the in­
dicator light turns off.
• Coolant temperature : too high . Let engine
run with vehicle stationary
Let t he engine ru n at idle fo r a few mi nutes to
cool off, until t he in dic ator lig ht tur ns off .
- If the ind icator light does not tu rn off , do no t
con tinue drivi ng the veh icle. See an authoriz ed
Aud i de aler o r au th ori zed Audi Serv ice Facili ty
for a ssistance.
.&_ WARNING
- Never ope n the hood if you ca n see or hea r
s team or coo la nt escaping from t he en gine
compa rtment. This increases the risk of
burns. Wait until you no longer se e or h ear
steam or coo lant escaping.
- The engine compa rtment in any vehicle can
be a dan gerous a rea. Stop the engine and
allow it to cool befo re wor king in the engine
compa rtment . Always follow the informa­
tion fo und in
c::, pag e 244, Working in the
e ngine compartment .
(D Note
Do not continue driving if the . indicator
li ght tur ns on as this increases the risk of en·
g ine damage.
"l!:1': Engine oil pressure
• Turn off engine. Oil pressure too low
Stop the engine and do not co nti nu e driving.
Check the eng ine oi l level
c::, page 248 .
-If the eng ine o il level is too low, add engine oil
c::, page 248 . Only continue driving once the in-
dicator light turns off. .,,.

co
co
.... N
" N .... 0
0
Vl c:o
-If the engine oil level is correct and the indica­
tor light still blinks , turn the engine off and do
not continue driving. See an authorized Audi
dealer or authori zed Audi Service Facility for as­
sistance.
The oil pressure warning is not an oil level in­
dicator. Always check the oil level regularly.
0 Generator/vehicle battery
• Electric system: malfunction! Battery is not
being charged
T here is a malfunction in the alternator or the ve­
hicle electrical system.
Drive to an authorized Audi dealer or authorized
Audi Service Facility immediately. Turn off all un­
necessary electrical equipment because it will
drain the battery . See your authori zed Audi deal­
er or authorized Audi Service Facility if the bat­
tery charge level is too low .
(•) Electrical system: low battery charge. Bat·
tery will be charged while driving
The starting ability may be impaired.
If this message turns off after a little while , the
vehicle battery charged enough while driving.
If the message does not turn off, have an author­
ized Audi dealer or authorized Audi Service Facili­
ty repair the malfunction.
~ Engine stop while driving
• Engine stopped: no power steering or brake
servo possible
There is a malfunction in the engine or in the fuel
supply system .
More force is needed to steer and brake the mov­
ing vehicle when the engine is stopped. If the ve­
hicle is rolling , try to bring it to a stop off to the
side from moving traffic. See an authorized Audi
dealer or authorized Audi Service Facility for as­
sistance .
Instruments and indicator lights
A WARNING
-
If the engine stops while driving, you will
need to use more force to brake the vehicle .
This increases the risk of an accident . There
will still be power steering if the ignition is
switched on while the vehicle is rolling and
there is sufficient battery charge. Otherwise,
you must use greater force when steering.
~ Front safety belt
The. indicator light stays on until the driver's
and front passenger's* safety belts are fastened.
Above a certain speed, there will also be a warn­ ing tone.
@ Tips
For additional information on safety belts,
see
c::> page 189.
C l~ Rear safety belt
Applies to : vehicles with rear safety belt detection
The respective indicator light will turn on briefly
when a safety belt on the rear seats is fastened
or unfastened .
111-If this indicator light turns on briefly, the
safety belt on the rear seat is not fastened.
II-If this indicator light turns on briefly, the
safety belt on the rear seat was fastened.
• -If this indicator light blinks, the safety belt
was unfastened while driving. Above a certain
speed, there will also be a warning tone .
(D Tips
For additional information on safety belts,
see
¢page 189.
~ - Steer ing lock
• Steering: malfunction! Please stop vehicle
There is a malfunction in the electronic steering
lock. You cannot turn the ignition on.
Do
not tow your vehicle because it cannot be
steered. See an authorized Audi dealer or author-
ized Audi Service Facility for assistance.
1111>
13

co
co
.... N
" N .... 0
0
Vl c:o
nearest authorized Audi dealer or authorized
Audi Service Facility and have the malfunction
corrected.
@ Tips
For additional information on ESC and ABS,
see
~ page 88.
(0) Brake pads
EiJ Brake pads: wear limit reached. You can con­
tinue driving. Please contact Service
The brake pads are worn.
Drive to an authorized Audi dealer or authorized
Audi Service Facility immediately to have the
brake pads checked.
Applies to: USA models
The EiJ indicator light turns on together with the
11111 indicator light
.!f Safety systems
The El indicator light monitors the safety sys­
tems.
Safety system
If them indicator light turns on or blinks, there
is a malfunction in a safety system .
Drive to an authorized Audi dealer or authorized
Audi Service Facility immediately to have the
malfunction corrected.
_& WARNING
Have the safety systems inspected immedi­
ately. Otherwise, there is a risk that the sys­
tems may not activate during a collision,
which increases the risk of serious injury or death.
c±:, Engine control
-
If the II indicator light turns on if there is a mal­
function in the engine control.
Drive slowly to an authorized Audi dealer or au­
thorized Audi Service Facility to have the engine
checked.
Instruments and indicator lights
o Malfunction indicator lamp (MIL)
The malfunction indicator lamp (MIL) is part of
the On Board Diagnostic system (OBD II). The
¢'4 c;ymbol turns on when the ignition is switched
on and turns off again once the engine is started
and running at a steady idle speed. This indicates
that the MIL is functioning correctly.
The indicator light turns on if there is a malfunc­
tion in the engine electronics. See an authorized
Audi dealer or authorized Audi Service Facility to have the malfunction corrected .
For additional information, see
c::> page 17.
!?i Engine speed lim itation
Applies to: vehicles with engine speed limitation
(II maximum engine speed: XXXX rpm
The engine speed is automatically limited to the
speed displayed in the driver information system.
This protects the engine from overheating .
The engine speed limitation deactivates once the
engine is no longer in the critical temperature
range and you have released the accelerator ped­
al once.
If the engine speed limitation was activated by
an engine control malfunction, the
II indicator
light also turns on. Make sure the engine speed
does not go above the speed displayed, for exam­
ple when downshifting. Drive to an authorized
Audi dealer or authorized Audi Service Facility im­
mediately to have the malfunction corrected.
~ .. Engine oil level (min. )
II Please check oil level
You may continue driving for the time being.
Check the engine oil level as soon as possible
c::> page246.
-If the engine oil level is too low, add engine oil
~page 248.
- If the engine oil level is correct and the indica­
tor light still turns on, drive at low engine
speed to an authorized Audi dealer or author­
ized Audi Service Facility .
15

Instruments and indicator lights
'1=1";.. Engine oil sensor
• Oil level sy stem : malfunction! Plea se con­
tact S ervic e
The senso r to check the engine oil level has
fa iled. Drive to an au thorized Aud i dea le r or a u­
thor ized Audi Se rvice Facil ity immediate ly to have
the ma lfun ction co rrected.
II O il l ev el sen sor : oil chang e nece ssar y. Plea se
con tact Service
The engine oil leve l is too high.
Drive to an a uthorized Audi dea ler or authorized
Aud i Serv ice Facility immediately to have the
malfunct ion corrected.
CJ) Note
Refer to the description in the Owner's Man­
ual ¢
page 248, Checking the engine oil level
and adding engine oil.
Bl Tank system
00] Pl ea se refuel
If the indicator lig ht turns on for the first time
and the message appears, there are about 1.9
ga l (7 L) of fue l left in the tank.
D Plea se refuel immediately
If the ind icator lig ht turns on the message ap­
pea rs, the fue l tank is almos t empty. Refuel the
veh icle immed iate ly.
D Tan k system : ma lfun ction! Plea se contact
Servic e
If the indicator light turns on and th is message
appears, there is a malfunction in the tank sys­
tem.
Drive to an authorized Aud i dealer or authorized
Aud i Serv ice Facility immediately to have the
malfunct io n corrected.
@ For the sake of the environment
Fuel should never enter the sewer system or
come into contact w ith the ground.
16
(D Tips
More information on refueling is available on
page ¢
page 241 .
~ Washer fluid level
m Please add washe r fluid
Fill the washer fluid for the windshie ld washer
system and the headlight washer system* when
the ignit ion is switched off¢
page 253.
@wind shield wipers: malfunction! P lease
conta ct Se rvice
There is a ma lfunction with the windsh ield wip­
ers .
Drive to an authorized A udi dealer or authorized
Audi Service Facility immediate ly to have the
malfunction corrected .
. ·: If the II ind icator light turns on, a bulb has
failed. The message indicates the location of the
bulb .
Replace the bulb immediately.
Vehicle light s: malfunction! Please contact
Ser vice
There is a m alfu nction in the headlights or the
li gh t sw itch. Dr ive to an a uthor ized Audi dealer or
a uth orized Aud i Serv ice Facili ty immedia tely to
have the malfunction cor rected.
_& WARNING
- Light bulbs a re under p ressure and can ex­
plode when b ulbs are replaced, wh ic h in­
creases the risk of injury .
- With gas -discharge lamps* (xenon head­
lights), the high-vo ltage component must
be handled appropriately. Otherw ise, there
is a risk of fatal injury .

co
co
.... N
" N .... 0
0
Vl c:o
Driving
General information
Breaking in
A new vehicle must be broken in, and the break­
in distance should be 1,000 mi les ( 1,500 km). Do
not drive at speeds that w ill exceed
2/3 of the
maximum permitted engine speed
(RPM) for the
first 600 miles (1,000 km) , and avoid full accel­
eration during this period . You may gradually
start increasing the
RPM and the speed between
600 miles (1,000 km) and 1,000 miles (1,500
km).
During the first hours of use, the engine has a
higher internal friction than later on when all
moving parts have settled into place with each
other.
How the vehicle is driven during the first 1,000
miles (1,500 km) also affects the engine quality.
Drive at moderate engine speeds after the initial
break-in per iod, part icularly when running a cold
engine . This will reduce engine wear and improve
the mileage .
Do not drive at too low of an engine speed (rpm).
Shift down if the engine stops running "smooth­
ly" . Extremely high eng ine speeds are automati ­
cally reduced .
Avoid damaging the vehicle
When you are driving on poor roads, or over
curbs, steep ramps, etc., make certain that low­
lying parts such as spoilers and exhaust system
parts do not bottom out and get damaged.
This is especially true for vehicles with low-slung
chassis (sports chassis)* and fully loaded
vehicles.
Driving through water on roads
Note the following to reduce the risk of vehicle
damage when driving through water, for examp le
on flooded roads :
- The wate r must not be any higher than the bot­
tom of the vehicle body .
Driving
- Do not drive faster than walking speed.
A WARNING
After driv ing through water or mud, the effec­
tiveness of the brakes may be reduced due to moisture on the brake rotors and brake pads.
A few careful brake applications should dry
off the brakes .
(D Note
Vehicle components such as the engine,
transmission, suspension or electrical system
can be severely damaged by driving through
water.
(D Tips
- Determine the depth before driving through
water.
- Do not stop the vehicle, drive in reverse or
switch the engine off when driving through
water.
- Keep in mind that oncoming vehicles may create waves that raise the water level and
make it too deep for your vehicle to drive
through safely.
- Avoid dr iving through salt water, because
this can cause corrosion.
Economical and environmentally-friendly
driving
T he amount of fuel consumpt ion, the environ­
menta l impact and the wear to the engine,
brakes and tires depends mostly on your driving
style. With an anticipatory and economic driving
style, fuel consumption can be reduced by ap­
proximately 10-15%. The following tips will help
you conserve the environment and your money at
the same time .
Anticipatory driving
A vehicle uses the most fuel when accelerating.
When you drive with anticipation, you do not
need to brake as often and so you accelerate less.
When possible, let your vehicle coast with a
gear
engaged -
for example, when you notice that the
next traff ic light is red . .,,.
55

co
co
.... N
" N .... 0
0
Vl c:o
Facility immediately to have the malfunction cor­
rected. The color of the indicator light depends
on the vehicle speed.
A WARNING
-
Driving at higher speeds without the rear
spoiler deployed can impair handling charac­ teristics, making the vehicle harder to con ­
trol.
- Always make sure that the spoiler is de­
ployed when driving at speeds over 85 mph
(140 km/h). If the rear spoiler warning/indi­
cator light in the instrument cluster comes
on, the rear spoiler may not have deployed.
- Never drive at speeds higher than 85 mph
(140 km/h) if the spoiler is not deployed .
Have the spoiler inspected as soon as possi­
ble by an authorized Audi dealer or qualified
workshop.
- Always obey speed limits and other traffic
laws.
A WARNING t =
Improper operation of the rear spoiler can
cause crushing injuries.
-
- Always make sure that nobody, especially
children, is in the way when the rear spoiler
is deployed or retracted.
(D Note
- Never push on the vehicle on the rear spoil­
er. This could cause damage.
- To prevent damage to the rear spoiler do
not lean or place anything on it.
- Only operate the rear spoiler manually when
the luggage compartment lid is close and
the rear spoiler moving parts are not
blocked. Otherwise, damage could occur.
@ Tips
Clean the rear spoiler compartment every 2 to
3 months. To function correctly, the rear
spoiler must be free of ice , snow and leaves.
Intelligent Technology
Energy management
The starting ability is optimized
The energy management system manages the
electrical energy distribution and optimizes the
availability of electrical energy for starting the
engtne.
When a vehicle with a conventional energy sys­
tem is not driven for a long time, the vehicle bat­
tery is drained by equipment (for example, the
immobilizer). In certain circumstances , there
could may not be enough energy to start the en­
gine.
Your vehicle is equipped with an intelligent ener­
gy management system for distributing electrici­
ty. This significantly improves the starting ability
and increases the vehicle battery life.
The energy management system Is made up of
battery diagnosis, idling current management
and dynamic energy management.
Battery diagnosis
The battery diagnosis determines the vehicle bat ­
tery charge level. The sensors determine the bat­
tery voltage, the battery current, and the battery
temperature. The current charge level and the
performance of the vehicle battery are deter­
mined based on this.
Idling current management
The idling current management decreases the
energy used while parked. With the engine
switched off , it manages the energy distribution
to the different electrical components. Data from
the battery diagnosis is taken into account for
this.
Depending on the vehicle battery charge level,
electrical equipment is switched off one item af­
ter the other to prevent the vehicle battery from draining and to maintain the starting ability.
Dynamic energy management
While driving , dynamic energy management dis­
tributes the appropriate amount of energy to the
electrical equipment.
It controls the battery
charge level so that the amount of energy is not ..,_
93