2017 AUDI TT COUPE turn signal

co
co
.... N
" N .... 0
0
Vl c:o
(D Note
Never drive until the tank is completely emp­
ty. The irregular supply of fuel that results
from that can cause engine misfires . Uncom­
busted fuel will then enter the exhaust sys­
tem. This can cause overheating and damage
to the catalytic converter .
Indicator lights
Description
The indicator lights in the instrument cluster
blink or turn on. They indicate functions or mal­
functions.
With some indicator lights, messages may ap­pear and warning signals may sound. The indica­
tor lights and messages in the display can be cov­
ered by other displays. To show them again, se­ lect the tab for the indicator lights and messages
using the multifunction steering wheel
c;, page 19. If there are several malfunct ions,
you can display them one at a time using the
thumbwheel.
Some ind icator lights in the display can display in
several colors .
Overview
Some indicator lights turn on briefly as a function
check whe n you switch the ign ition on . These sys­
tems are marked with a
,I in the following tables.
If one of these indicator lights does not turn on,
there is a ma lfunction in that system.
Red indicator lights
---------------
US A models :
Brake system ./ c;, page 10
Canada models:
Brake system ./ c;, page 10
USA models : electromechanical
parking brake¢
page 11
Canada models: electromechanical
parking brake¢
page 11
Cooling system
<=>page 12
Instruments and indicator lights
Engine oil pressure
c;,page 12
Alternator
¢ page 13
Engine stop while driving
¢page 13
Safety be lt
c;, page 13 c;, page 13
Electromechanical steering./
c;,page 91
Steering lock
¢page 13
Central indicator light
c;,page 14
Engine start system
c;,page 14
Transmission malfunction
c;, page 68
Rear spoiler
c;,page 92
Yellow indicator lights
Electronic Stabilization Contro l (ESC)
,I c;, page 14
Electronic Stabilization Control (ESC)
./ c;, page 14
USA models: anti-lock braking sys­
tem (ABS)./
c;, page 14
Canada models: anti-lock braking
system (ABS) ./
c;, page 14
Safety systems ,I
c;,page 15
USA models:
Brake pads c;, page 15
Canada models:
Brake pads c;, page 15
Electromechanical parking brake
c;,page 11
Tire pressure monitoring system../
<=>page 273
Tire pressure monitoring system
<=>page 273
9

Instruments and indicator lights
Engine control
c::> page 15
Emi ssions control system
c::> page 15
Engine speed limitat io n
c::> page 15
Engine oil level
c::> page 15
Engine oil senso r
c::> page 16
Battery charge
c::> page 13
Tank system
c::> page 16
Washer fluid level
c::> page 16
W indshield wipe rs
c::> page 16
Remote control key
c::> page 58
Battery in remote control key
c::> page 27
Bulb failure ind icator *
c::> page 16
Headlight range control system
c::> page 17
Adaptive light*
c::> page 17
- Light/
rain sensor*
• c::> page 17
Transmiss ion
c::> page 68 0
. . I I
~-e ... , . , ,.
I .
©-e .... , .. ,
&
Central indicator light
c::> page 14
@!
Electromechan ical steer ing./
c::> page 91
;
Adapt ive dampers*
c::> page 17
10
Rear spoiler
c::> page 92
Other indicator lights
- T
ur n signals
Ii ii c::> page 17
y>))
D
Rea r safety be lt./
c::> page 13
USA mod els : cru ise cont rol system*
c::> page 70
C anada models : cruise control sys ­
tem *
c::> page 70
Active lane assist*
c::> page 73
Conven ience key
c::> page 59
Electromechanica l park ing brake
c::> page 11
Active lane assist*
¢ page 73
Audi side assist *
c::>page 78
Transm iss io n
c::> page 68
Electromechan ica l park ing brake
c::> page 11
Rear safety belt./
c::> page 13
Rear safety belt./
c::> page 13
USA models: speed warn ing sys­
tem"
c::> page 70
Canada models: speed warn ing sys­
tem*
c::> page 70
High beams
<=:> page 37
BRAKE /{(JJ) Brak e sys te m
If this indicato r light turns on, there is a malfunc-
tion in the b rake system .
.,.

co
co
.... N
" N .... 0
0
Vl c:o
~(D Headlight range control system
Iii Headlight range control : malfun ction! See
owner' s manual
There is a malfunction in the headlight range
control system, which may ca use g lare fo r othe r
d rivers.
Drive to an aut horized Aud i dea le r o r a uthorize d
Aud i Service Facility immediately to have t he
malfunct ion corrected .
§0 Audi adaptive light
Appl ies to: ve hicles with Audi adaptive light
l;J Audi adaptive light: malfunction! See own­
er's manual
There is a malfunc tion in the adapt ive lig hts . T he
h eadligh ts still f unction.
Drive to an authorized Aud i dea ler or authorized
Aud i Service Fac ility immediately to have t he
mal funct ion corrected .
~ Light/rain sensor
El Automatic headlights: malfunction! See
owner 's manual
El Automatic wipers: malfunction! See owner's
manual
The light/rain sensor is malfunct io ni ng .
The low beams remain switched on at all times
for safety reasons when the light switch is in the
AUTO position. You can continue to tur n the
lights on and off using the light switch. You can
still cont rol a ll w iper functions that are inde ­
pendent of the ra in sensor .
Drive to an authori zed Aud i dea le r or a uthori zed
Aud i Service Facility immediately to have the
malfunct ion corrected .
; Adaptive dampers
A ppl ies to: ve hicles w ith Audi drive select
B Suspension : malfunction! You may continue
driving
There is an adaptive damper malf unct ion.
Instruments and ind icator lights
D rive to an au thori zed A udi dealer or au tho rized
Audi Se rvice Facility immed iate ly to have the
malfunction corrected.
¢i ¢ Turn signals
If the . or 1B indicator light blinks, a turn sig­
nal is turned on . If both indicato r lights a re blink­
i ng, the emergency flashers are on .
On-Board Diagnostic
system (OBD)
Malfunction indicator lamp (MIL)
The malf u nction ind icator lamp ( MIL) ¢4 in t he
i ns trument cluste r is pa rt of the On Board D iag­
nost ic System (OB D II).
The wa rning/indicator lig ht tu rns on when the ig­
nition is switched on and turns off once the en­
gine is started a nd is r unning in idle at a s table
spe ed . T his ind icates t hat the MIL is f unct io ni ng
c or rectly.
If the lig ht does not turn off after start ing the
engine or t urns o n while drivi ng, this may ind i­
cate there is a malfunction in the eng ine . If the
i ndica to r tur ns o n, the cata lytic conve rter m ay be
d am aged .
Drive
with reduced engine performance (avo id
high speeds for extended per iods of t ime and/o r
fast accele rat ion) and have the ma lfu nction cor­
rec ted . See an aut hor ized A udi de aler or au thor­
i z ed Audi Service F acili ty.
T he in dicator may turn on if the e lectro nic speed
li mi ter is faulty. For ad dit io nal informa tio n, see
~ page 70, Ele ct ronic speed limite r.
17

CD
CD
.... N
" N .... 0
0
Ill co
Opening and closing
Central locking
Description
You can lock and u nlock the veh icle centrally . You
h ave the following options:
- Remote contro l key <=>
page 2 7,
- Sensors in the door hand les*
<=> page 28,
-Lock cylinder on the driver's door<=> page 30,
or
- Centra l locking switch inside<=>
page 29.
Auto Lock
The Auto Lock f uncti on lock s all doors and the
l uggage compartment lid on ce the spee d has ex­
ceede d approximately 9 mph (15 km/ h).
The vehicle can be unlo cked if the open ing f unc­
t ion in the centra l loc king system sw itch is used
or one o f the door ha nd les is pulled. The Auto
L oc k function can be sw itched on and off in the
I nfotainment system
<=> page 29.
In the event of a crash wi th air bag deployment,
t he doors will a lso automa tic all y unlock to allow
access to the ve hicle.
Selective unlocking
The doo rs and luggage compartmen t lid w il l lock
when they close . You can set in the Infotainment
sys tem w hether
only the d river's door or the en­
tire ve hicl e should be unlocked when unlocking
<=> page 29 .
Turn signals
The tu rn s ignals flash tw ice when you unlock the
ve hicl e and f lash once when you lock the veh icle.
If the b linki ng continues, one of the do ors or the
l uggage compartment lid is not closed or the ig­
nition is still switched o n.
Unintentionally locking yourself out
The follow ing cond it io ns prevent you from lock­
in g your remo te contro l key in the vehicle :
- If the dr iver's door is open, the veh icle cannot
be locked by pressi ng the
ill] button o n the re-
Open ing and closing
mote contro l key o r touching the locking sen­
sor* on a door.
- W he n l ocki ng us ing the ~ button in the central
loc king switch, the vehicle will not lock if a door
is open <=>
page 29.
-On ve hicles with a convenience key*, the lug ­
gage compartment lid unlocks again after clos­
ing if the most recent ly used key is in the lug­
gage compartment. The emergency flas hers
blink four times .
Do not lock your vehicle w ith the remote cont rol
key or convenience key* until all doors and the
l u ggage compartment lid are closed . Th is helps
to prevent you from lock ing you rself out acciden­
tally .
(D Tips
- Do not leave val uables unattended in the ve­
hicle. A locked vehicle is not a safe!
- The LED in the driver's door rail blinks when
you lock the veh icle. If the LED lights up for
app roximately 30 seconds after lock ing,
there is a malfunction in the centra l locking
system . Have th e problem cor rected by a n
authoriz ed A udi dealer o r authoriz ed Audi
Service Facili ty.
Key set
Fig . 14 Yo ur veh icle key set
@ Remote control key with integrated
mechanical key
.. .... N
~ a)
You can unloc k/lock you r vehicle wi th the remo te
c ontro l key . A me chani cal key is in tegr ated in the
r emote cont rol key¢
page 26 . ll>
25

Opening and closing
Programming the transmitter
Applies to: vehicles with garage door opener (Homelink)
Fig. 29 Distance between t he rad iator grille and the re­
mote control transmitter
Programming the button : step 1 on the
control panel
1. Switch on the ignit ion.
2. Press both of the outside buttons on the con­
trol unit¢
page 33, fig. 28 until the yellow
LED @turns off and the green LED@ blinks.
This procedure clears the standard codes that
were set at the factory and does
not need to
be repeated again to program the other but­
tons.
3. Briefly press the button in the control panel
that you want to program.
4. Wait until the yellow LED@blinks. The pro­
gramming mode is active for 5 minutes.
5. Go in front of the vehicle with the original re­
mote control transmitter for the system that
you are programming to the control panel
button.
Programming the button: step 2 at the
radiator grille
6. Ho ld the remote control transmitter at the
vehicle radiator grille¢
fig. 29.
7. Now press the remote control transmitter
until the turn signals on your vehicle blink.
This can take up to 30 seconds.
8. If the emergency flashers blink three times,
the programming was successful.
If the
emergency flashers only b link one t ime, the
five-minute time limit for programming has
expired or the programming was unsuccess­
ful. Repeat the programming starting from
the third step or change the distance to the
radiator grille.
34
9. If the garage door or other systems do not
open with the Homelink buttons even if the
programming was successfu l, the system
may use a rolling code instead of a fixed
code. You must also then perform
rolling
code programming
c:, page 35.
The other two buttons in the control panel can be
programmed using the instructions given above.
Start with step 3.
Deleting button programming
The programmed buttons cannot be deleted indi­
vidually. They must be deleted all at once. Repro ­
gram the buttons if necessary.
.,.. Switch on the ign ition.
.,.. Press both of the outside buttons on the con­
trol unit until the yellow LED @turns off and
the green LED(!) blinks .
Reprogramm ing buttons
.,.. Switch on the ignition .
.,.. To reprogram an individual button, press the
desired button until the green LED @turns off
and the yellow LED@starts to blink (after ap­
proximately 20 seconds). Release the button
immediately. The programming mode is active
for 5 minutes.
.,.. Continue with step 5.
(D Tips
- The distance needed between the remote
control transmitter and the Homelink mod­
ule in the radiator grille
¢fig. 29 depends
on the system you are programming.
- Depending on the system model, you may
need to release the button on the remote
control transmitter while it is programming
and press it again . Hold every position you
try when programming for at least 15 sec­
onds before trying a new position. Keep an
eye on the vehicle turn signals while doing
this.

CD
CD
.... N
" N ...... 0
0
Ill co
-If the battery has been discharging for a
wh ile, the parking light may sw itch off auto­
matically. Always make sure your vehicle is
parked and adequately lit according to the
laws . Avo id using the parking lights for sev­
eral hours.
- Always observe legal regulations when us­
ing the light ing systems described.
(D Tips
- The light sensor for the automatic head­
lights* is in the rearview mirror mount. Do
not place any stickers in th is area on the
windsh ield.
- Some exterior lighting functions can be ad­
justed
Qpage 37.
-If you turn off the ignition wh ile the exterior
lights are on and open the door, a warning
tone so unds .
- In some markets, the ta il lights will sw itch
on when the dayt ime run ning lights switch
on.
- In cool or damp weather, the inside of the
headlights, turn signals and tail lights can
fog over due to the temperature difference
between the inside and outs ide. They will
clear short ly after switching them on. This
does not affect the service life of the light­
ing.
Turn signal and high beam lever
The Lever operates the turn signals, the high
beams and the headlight flasher.
@
,
t
@
F ig. 31 Turn signal and high bea m lever
N
5 0
~ a:,
Lights and V ision
Turn signals ¢ 9
The turn signa ls act ivate when yo u move the lev­
er into a turn signal position when the ignition is
switched on.
(D -rig ht tu rn signal
@ -left turn signal
The turn signa l blinks three times if you tap the
lever (convenience turn signa l).
High beams and headlight flasher
~D
Move the lever to the corresponding position:
@ -high beams on
@-high beams off or headlight flasher
T he
II indicator light in the instrument cluster
turns on.
A WARNING
= H igh beams can cause glare for other drivers,
which increases the risk of an accident. For
this reason, only use the high beams or the
headlight flasher when they will not create
g lare for other dr ivers.
Adjusting the exterior lighting
The functions are adjusted in the Infotainment
system .
.,. Select in the Infotainment system: I MENU ! but­
ton> Vehicle > left control button >Vehicle set­
tings > Exterior lighting .
Automatic headlights
You can adjust the following settings in the Au­
tomatic headlights menu:
Activation time -you can adjust if the headlights
switch on Early, Medium or Late according to the
sensit ivity of the light sensor.
Audi adaptive light * -you can sw itch adaptive
light
On and Off .
Daytime running lights*
USA models: the daytime running lights can be
switched on or off using the MM I. Select
On or
Off .
37

CD
CD
.... N
" N ...... 0
0
Ill co
have the malfunction corrected. To start the en­
gine, press and hold the
! START ENGINE STOPI
button.
DJ R emot e control key : hold b ack of key
again st the d esignated are a. See owner's man­
ual
This message appea rs if the re is no convenie nce
key inside the vehicle or if the system does not
recognize the key . The conven ience key may not
be recognized, for example, if it is cove red by an
object that
disrupts the signal (such as a brief ­
case), or if the key battery is weak. Electronic de­
vices such as cell phones can also interfere with
the signal.
To still be able to start or stop the eng ine, see
c:::> page 59, Starting the engine when there is a
malfunction .
Ill Remote control key : key not recogn ized . Is
the ke y still in th e vehi cle?
The Ill ind icator light turns on and this message
appears if the conve nience key was removed from
the vehicle when the engine was running.
If the
conven ience key is no longer in the vehicle, you
cannot switch the ign ition on or start the engine
once you stop it. You a lso cannot lock the vehicle
from the outside .
Please press brake p edal
This message appears if you do not press the
brake pedal when starting the eng ine.
Please pr ess clut ch p edal
This message appea rs in vehicles w it h manual
transmissions if you do not press the clutch pedal
when sta rting the engine . The engine can on ly be
started when t he clu tch pedal is pressed.
Pl ease select N or P
This message appea rs when starting or stopping
the eng ine if the selector lever is not in the Nor P
position . The engine will not start/stop.
Shift to P , otherw ise vehi cle can roll awa y.
Doors can be lo cked i n P only
This message appears for safety reasons a long
with a warning tone. It appears if the selector
lever for the automatic transmission is not in the
D rivi ng
P position when switch ing the ignit ion off w ith
the
I START ENGINE STOPI b utton. P lace these­
l ector lever in the P position. The veh icle cou ld
roll if the lever is not in P. You also cannot lock
the vehicle using the locking sensor on the door handle or using the conven ience key .
Starting the engine when there is a
malfunction
It may not be possible to start the engine under
certain circumstances, for example if th e battery
in the vehicle key is drained, if interference is af­
fected the key or if there is a system malfunc­
tion.
F ig. 61 Steering column/ remote control key: starting the
e n g in e if there is
a m alfunct ion
As long as the message y >l) Remote control key :
hold back of key against the designated are a.
See owner's manual
is displayed, you can emer­
gency start your vehicle.
.. Press the brake pedal
c:::> .&. in Starting the en­
gine on page 57.
... Press the ~I s=T ~A ~ R~ T~ E_N _G _I _N =E - S~ T= o- P~I button .
.,. Ho ld the master key in the location ind icated as
shown in the illustrat ion
y >l) c:::, fig. 61. The engine
w ill start.
.. If the engine does not automat ica lly start,
press the
! S TART ENGINE STOPI butto n again .
(D Tips
You can view the message aga in by pressing
the
I S TA RT ENGINE S TOP I button.
59

Ass is t
Assist
Electronic speed Limiter
Your vehicle may be factory equipped with tires
that are rated for a maximum speed of 130 mph (210 km/h). This is less than the maximum speed
of your vehicle. To reduce the risk of sudden tire
failure and loss of control if the vehicle is operat­
ed at excessive speeds, your vehicle also has an
electronic speed limiter. The electronic speed
lim iter prevents your vehicle from going faster
than the t ire speed rating. For mo re information
~page 262.
If the engine control unit receives faulty vehicle
road speed signals, the Malfunction Indicator
L amp (MIL)
¢..ffi will illumina te. If this occurs,
con tact the nearest au thorized A ud i dealer for
assistance.
_& WARNING
Always observe the posted speed limits and
adjust you r speed to suit prevailing road, traf­
fic and weather conditions. Never drive your
vehicle faster than the maximum speed rating
of the tires installed.
Speed warning system
Applies to: vehicles with speed warning system
The speed warning system helps you to stay be­
low a specified maximum speed that can be set,
changed or deleted in the Infotainment system . -
The speed warning
system warns you if you are
exceeding the maximum speed that you have set.
A warni ng tone will sound as soon as you r speed
exceeds the sto red value s lightly. The
(OJ (USA
models)
I [OJ (Canada models) indicator light
and a message appear i n the ins trumen t cluster
d isp lay a t the same time. Th@
Hll (USA models)/
[O](Canada models) in dicator light and the mes­
sage turn off when the vehicle speed drops be low
the stored maximum speed.
Se tting a threshold is rec om mended if you would
like to be reminded when yo u reach a certa in
maximum speed . Situations where you may want
to do so include driving in a country w it h a ge ne r-
70
al speed limit or if there is a spec ified maximum
speed for winter tires.
Setting the warning threshold
.,. Select in the Infotainment system: IMENU ! but­
t on
> Vehicle > left con trol b utton > Driver as ­
sistance > Speed warning > Manu al.
a) Tips
Regar dless of the speed warning sys tem, you
sh ould alw ays mon itor your spee d using the
speedometer and tnake s ure yo u are fo llow ing
the lega l speed limit.
Cruise control system
Switching on
Applies to: vehicles with cruise control system
The cruise control system makes it possible to
drive at a constant speed starting at 15 mph
(20kmlh).
0
f
~
0
F ig. 70 Operat ing lever: crui se control system
.,. To switch on the system, pu ll the lever into po -
sition @~
fig. 70.
.,. Drive at the speed to be maintained.
.,. To store the speed, press the button @.
The stored speed and the
M;\1)~1j (USA models) /
l'I (Canada models) indicator light are displayed
in the instrument cluster.
The speed is maintained by modifying engine
power or through an active brake intervention.
_& WARNING
-Always pay attention to the traffic around
you when the cruise contro l system is in op­
erat ion. You are always respons ible for your ,...