2017 AUDI Q5 warning

Instruments and indicator lights
¢ Q Turn signals
The indicator light blinks when you use either
turn signal.
Whenever you use the left B or the right.
turn signal, the indicator l ight blinks. When you
use the emergency flashers, both indicator lights
flash.
If one of the turn s ignal light bulbs burn out, the
turn signal w ill blink twice as fast as normal.
This does not apply, however, in towing mode .
The indicator light does not flash if a turn s ignal
is out on the tra iler or the towing vehicle. Addi­
tional informat ion on the turn s ignals
c::> page52.
¢1.~ Trailer turn signal assembly
Appl ies to: ve hicles w ith towing hitch
The indicator light also blinks if the turn signal is
operated when towing a trailer .
The indicator light . blinks when the turn sig­
na l is used, if a trailer has been p roperly connect­
ed to the vehicle .
If one of the turn signal bulbs on the trailer is burned out or defective, the indicator light will
not blink when you use the turn s ignals.
@ Tips
For vehicles with a factory installed towing
hitch or a tra ile r hitch that was installed later
according to factory specif ications, the trailer
turn signa l assembly is actuated.
~ Safety belts
This warning/indicator light reminds you to put
on your safety belt.
The . warning/indicator light illuminates when
the ignition is switched on to remind the dr iver
and (on USA models only) any front passenger to put on the safety belt. Add itionally, an audible
warn ing tone w ill also sound .
For more Information
c::> page 140, Safety belt
warning light.
14
o Malfunction Indicator Lamp (MIL)
The Malf u nction Indicator Lamp ( MIL) is pa rt of
t h e On-Boar d Diagnos tic ( OBD II) sys tem . T he
symbol
('4 li ghts up when the ignit io n is t urned
on and will turn off after the engine has s tarted
and has settled at a constant idle speed. This in­
dicates that the MIL is work ing properly.
The warning light ill uminates w hen the re is a
malfunction in the engine electronic system.
Contact your authorized Audi dea ler and have the
malfunction corrected .
An improperly closed fuel filler cap may al so
cau se the MIL light to illuminate (only vehicle s
with gasoline engine )
c::> page 212.
For more info rm ation c::> page 23 .
l[D High beam
The SI warning/ indica to r li ght illum ina tes when
the high beams are on or when you use the head­
li ght f lasher. Fo r more information about using
the high beams, see
c::> page 52.
CRUISE/"(') Cruise control
The lij;\1)~14 (USA mode ls) 1B (Canada mode ls)
warning/indicator light illuminates when the
c ruise contro l is activated .
ABS/(8) Anti-lock brake system (ABS)
This warning/indicator light monitors the ABS
and the electronic differential lock (EDL) .
The rJln (USA models) lri] (Canada models)
warning/indicator light will come on for a few
seconds when the ignit ion is switched on . The
li ght w ill go out after an automatic check se­
quence is comp leted.
There i s a malfunction in the ABS when:
-The warning/ indicator light does not illum inate
when you sw itch on the ign ition.
- The warning/ indicato r light does not go o ut af­
ter a few seconds .
- The warning/ indicator light illum inates while
driving. ..,.

CD
CD
.... N ,-... N ..... 0 0 C<'. 00
The brake system will still respond even with­
out the assi stance of the ABS system. See your
authorized Audi dealer as soon as possible to re­
store full braking performance.
For more infor­
mat ion regarding the ABS
¢ page 186.
The ABS warning light and the brake warning
light come on together. The ABS w ill not work
and you will not ice a change in braking re ­
sponse and performance.
Malfunction in the brake system
I f the b rake warning light¢ page 15 and the
ABS warning ill uminate
together there may be a
mal funct ion in the ABS, and there may also be a
malfunct ion in the brake system itself
c::> .&. .
In t he event of a malfunction in the brake sys­
tem
the warning/indicator light 1111 (USA mod ­
e ls)/ . (Canada models) in the instrument clus­
ter f lashes. By p ressing the
I SE TI button, you can
bring up a drive r message w hich explains t he
malfunct io n in more detail. Please no te
c::> page 2 5.
Malfunction in the electronic differential
lock (EDL)
The EDL works togethe r with the ABS . The ABS
war ning light w ill come on if there is a ma lf u nc­
tion in the EDL sys tem
c::> page 186 . See your au­
t hor ized Audi dealer as soon as poss ible.
.8, WARNING
- If t he 9 (U SA m odels)/ KO'A els) warn ing ligh t does not go o ut, o r if i t
comes on w hile driving, the ABS sy stem is
not wo rking prope rly . The vehicle can then
be stopped on ly with the standard brakes
(without ABS). You w ill not have the protec­
t io n ABS p rovides . Contact yo ur aut horized
Audi dealer as soon as poss ible .
- If the
1111 (USA models) . (Canada mod ­
els) b rake system indicator light t urns on to­
ge ther wi th the ABS a nd ESC indica to r
ligh ts, the ABS/ ESC regula ting func tion may
h ave failed. Func tions that s tabiliz e t he ve­
hicle are no lo nger av ailable . Thi s co uld
c a use the vehicle to swe rve and in crea se the
risk of sliding . Drive c arefully to t he nearest
-
Instruments and ind icator lights
author ized Audi dealer or ot her qualif ied
wo rkshop and have t he mal funct ion correct­
ed .
::~/(®) Electromechanical parking brake
The warning/indicator light monitors the elec­
tromechanical parking brake.
Wi th the pa rking bra ke app lied and the ig nit io n
tu rned on , the . (USA models)/ . (Cana-
da models) warning/indicator light illum inates .
A fter the ignition has been turned off, t he warn ­
ing/indicato r light continues to ill uminate for
abo ut 30 seconds . If the parki ng brake is applied
with the igni tion turned off, the warn ing/ indica­
tor light ill uminates for about 30 secon ds.
The wa rning/i ndicator lig ht wi ll go out when the
parking brake is released .
If the warning/ind icator light flashes continuous ­
ly
after applying the par king b rake, bra king force
is not sufficient to prevent the vehicle from roll­
ing unintentionally . P lease note the following :
- If the slope of the grou nd is too steep to park
the vehicle, the add it iona l drive message ap­
pea rs
Caution: Vehicle parked too steep .
-In the event o f a pa rking brake mal function,
the yellow
liJ symbol appears in the instru ­
ment cluste r display and the driver message
Parking brake malfunction! is d isplayed . Have
t he malfunction repaired as soon as poss ible by
an au thor ized A udi dealer or any ot her qualified
workshop.
BRAKE /(Q) ) Brake system
Th e warning/indicator light flashes if brak e fluid
level is lo w, if there is an AB S system malfunc­
tion or a p arking brake malfun ctio n.
T he 1111 (USA models) /. (Canada models)
li gh t illu min ates when t he igni tio n i s tur ned on.
It goe s ou t af te r th e e ng ine h as been st arted.
T h is ind icates t hat t he br ake w arning light is
f unct ioning properly.
If the brake warning light doe s not light up
when the engine is cranking, there may be a
15

Instruments and indicator lights
malfunction in the el ectric al sy stem. In this
case , contact an autho rized Audi deale r.
If t he b rake system war ning/ indica to r li ght flash­
es, there is a b rake system mal funct ion. By press­
ing the
! SE T! button, you can bring up a driver
m essage which explains the malf unction in mor e
detai l
¢pag e 25.
If the ABS fails, the ABS warning/indicator light
~ ( U SA mode ls)/ (IJ (Canada models) flashes
together with the brake system warning/indica­
tor light ¢& .
(USA models): If the warn ing light
1111 and the
warn ing light
Ii] ill uminate together , immedi ­
ately contact your authori zed Audi dea ler or
qualified workshop to have all brake pads in ­
spec ted
¢ page 29 .
When the light comes on, an audib le warning sig ­
na l is also given .
A WARNING
-If the 1111 (USA models) . (Canada mod­
els) brake system indicator light t urns on to­
gether with the ABS and ESC indicator
lights, the ABS/ESC regulating function may
have failed . Functions that stab ilize the ve­
hicle a re no longe r available . This could
ca use the vehicle to swerve and increase the
risk of sliding. Drive ca refully to t he nearest
autho rize d Aud i dealer or other quali fied
workshop and have the ma lfunction co rrect ­
ed.
- If the bra ke warn ing/indicator light does
not go out after a few seconds and the park­
ing brake is released, or lights up while you
are driving, the flu id leve l in the brake fluid
reservoir is too low. If you believe that it is
safe to do so, proceed immediately at low
speed to the nearest authorized Audi dealer
o r qualified repair facility and have the
bra ke system inspected.
- Always keep in mind tha t afte r severa l brake
applications, you will need greate r pressure
o n the brake pedal to stop yo ur vehicle. Do
not rely on straine d brakes to respond w ith
maximum stopping power in criti cal situa ­
tions . You must allow for increased braking
16
distances. The extra distance used up by
fading brakes co uld lead to an accident .

a,
a,
..... N r-­N ..... 0 0
0:
co
Driver information
system
Introduction
General notes
The driver information display inside the instru­
ment cluster provides you , the driver, with much
useful information.
Fig. 8 Instrument cl uster : ce nt er display
Information from the driver information system
is shown in the display in the center of the instr u­
ment cluster.
When you turn on the ignition and while you are
driving, some functions and vehicle components
are sca nned for their operat ing status. Malfunc­
tions or required service procedures are signaled
audibly and shown by red and yellow lighted
symbols and reminders to the driver in the dis­
play.
The driver is also shown information about rad io
and CD operat ion and directions for the naviga­
tion system*. You can find addit ional information
on these subjects in the radio or MMI* manual.
The illustrations in the instrument panel display
differ in some of the vehicles .
The driver information system provides the fol­
lowing functions:
Sound system disp lay
c:> page 17
Outside air temperature c:>page 18
Digital speedometer c:>page 18
Open door- and luggage com-c:> page 18
partment warning
Service interval display
c:> page 19
Driver in forma tion system
Auto Check system c:>page24
Driver information c:>page 24
Speed warning c:>page 91
Trip computer c:>page 19
Tire pressure monitoring system* c:>page247
Digital clock with date display c:>page 10
Odometer and trip odometer c:>page 10
Selector lever position c:> page 94
Cruise control c:>page92
Adaptive cruise control* c:>page 109
Energy flow display* c:>page 106
(D Tips
In the event of a malfunction either a red or
yellow icon appears in the display. Red sym­
bols indicate
Danger c:>page 25. Yellow
symbols indicate a
Warning c:> page 28.
Sound system display
Fig. 9 Display: sou nd system
l!3 .... 0 er. m m
If priority 1 or pr iority 2 faults are not shown by
the Auto Check Control, the name of the radio
station you are tuned to or the frequency and the
reception range are shown in the upper area of
the display .
When the CD is in use , the tit le of the track being
played is shown. The CD changer disp lays the
number of the current CD (CDl to CD6).
17

Driver i nf orm ati on sy stem
Outside temperature display
Fig. 10 D isplay : ou ts ide te m pe ratur e
At temperatures below 39 °F (+4 °C), a snowflake
symbol appears in front of the temperature dis ­
p lay . It is intended to remind the driver to pay
specia l attent ion to
ic e on th e ro ad .
If the vehicle is stationary, or if you are driving at
a very low speed, the temperature shown in the
display m ight be slightly higher than the act ual
outside temperature . T his is caused by the heat
be ing rad iated from the engine.
The unit of measurement for the temperature can be set in either °For in °Con the MMI* or on
the radio control un it. The outside temperatu re
d isp lay automatically shows the unit of measure­
ment that has been set. For add itional informa ­
tion, see the
MMI* or the rad io instruction man ­
ual.
A WARNING
- Never use the outside temperature display
to determine if a road surface is icy or not.
Keep in mind that road surfaces , especially
bridges and overpasses, could be ice cov­
ered and slippery even at an outside tem ­
perature above 39 °F (+4 °C) .
- Always remember, even if the "snowflake"
symbol ( ice warn ing) does not appear in the
display, black ice could be on the road .
-Always red uce your speed and drive with
special care in cold weather cond itions when
t h e chance of encounter ing icy road surfaces
increases.
18
Digital speedometer
Fig. 11 D isp lay: D ig ital speedomete r
Current speed appears in the display . Speed is
shown in
1 mph increments (USA models) or 1
km/h i ncrements (Canada models) .
You can switch the display from miles to k ilome­
ters and v ice versa via the radio or MM!*.
Open door or trunk lid warning
The pictogram alerts you when doors or the
trunk lid have been left open .
Fig . 12 D isp lay : Open door -and trunk lid warni ng
L'> 0
"' 0 ri:: m a,
The Open Door/ Tru nk Lid wa rning d isplays if even
one door, the hood or the trunk lid is open. This
symbol a lso shows
which door or lid has not been
closed
¢ fig . 12.
As soon as the doo r, the hood and the tr unk lid
are closed properly, the door and tr unk lid w arn­
i ng turns off and the selected driver in formation
system f unctions are disp layed again.

a,
a,
..... N r-­N ..... 0 0
0:
co
Service interval display
The service interval display reminds you when
your next service is due .
Fig. 13 Instrumel'lt cluster: Service interval display
8 .,, 0 ci:
"' ID
The schedule for the next oil change or inspec­
tion is calculated automatically and displayed ac­
cordingly. The display works in two stages :
Service reminder
30 days before the next service is due, a service
reminder appears in the display when you turn on
the ignition
¢ fig. 13.
After about 5 seconds the display switches back
to normal. The distance and time remaining are
updated each time the ignition is turned on until
the date due for service is reached.
Service due
When the due date for service is reached, the
message
Service due! appears in the instrument
cluster immediately after you turn on the igni­
tion . Additionally, a warning tone sounds. After
about
5 seconds the display switches back to nor­
mal.
Calling up the service schedules
If or when an oil change or inspection is due, can
be shown in the radio or MMI* display by select­
ing the service interval display in the car menu.
Select
I CARI function button > Service interval
display
or I CAR I function button > Car systems*
control button > Servicing & checks > Service in­
tervals .
Resetting the service interval display
Your authorized Audi dealer will reset the corre­
sponding service schedule after performing the
Driver information system
appropriate service on your vehicle. You also have
the possibility to reset the oil change schedule after having performed an oil change according
to Audi specifications. Select
I CAR I function but­
ton
> Service interval display> Reset oil change
interval
or ICARI function button > Car systems*
control button > Servicing & checks > Service in­
tervals > Reset oil change interval.
(D Note
- Only reset the oil change display when you
have completed an oil change.
- If you disconnect the battery terminals, no
calculations can be made for the service in­
terval display during this time and no serv­
ice reminder will appear. Remember that
observing the proper service intervals is vi­
tally important to extending the life of your
vehicle, particularly the engine, and main­
taining its value. Do not exceed the time in­
terval for the next service, even if the vehi­ cle mileage is low.
@ Tips
The information in the Service Reminder re­
mains stored even when the vehicle battery is
disconnected.
On-board computer
Introduction
The trip computer gives you information on cur­
rent and average fuel mileage, average speed ,
fuel range and driving time .
Fig. 14 Trip comp uter d isp lay: Average fuel mileage
19

a,
a,
..... N l"­N ..... 0 0
0:
co
On Board Diagnostic
System (OBD)
Malfunction Indicator lamp (MIL)
The Malfunction Indicator Lamp (MIL) ¢'4 in the
instrument cluster
¢ page 11, fig. 7 is part of the
On -Board Diagnostic (OBD II) system.
The warning/indicator light illuminates when the
ignition is switched on and goes out after the en­
gine starts and the idle has stabilized . This indi­
cates that the MIL is working properly .
If the light does not go out after the engine is
started, or illuminates while you are driving, a
malfunction may exist in the engine system .
If
the light illuminates, the catalytic converter
could be damaged.
Continue driving
with reduced power (avoiding
sustained high speeds and/or rapid accelera­
tions) and have the condition corrected. Contact
your authori zed Audi dealer.
If the light illuminates, the electronic speed lim­
iter may also be malfunctioning . For more infor­
mation ¢
page 23, Electronic speed limiter.
An improperly closed fuel filler cap may also
cause the MIL light to illuminate (only vehicles
with gasoline engine)
¢page 212.
On-Board Diagnostics
Fig. 20 Locat ion of Data Link Connec tor (DLC )
On-Board Diagnostics monitors the components
of your emission control system. Each monitored
component in your engine system has been as­
signed a code. In case of a malfunction, the com­ ponent will be identified and the fault stored as a
code in the control module memory.
Driver in forma tion system
The MIL light may also illum inate if there is a
leak in the on-board fuel vapor recovery system.
If the light illuminates after a refueling, stop the
vehicle and make sure the fuel filler cap is prop ­
erly closed (only vehicles with gasoline engine)
¢ page 212.
In order to make an accurate diagnosis, the stor­
ed data can only be displayed using special diag­
nostic equipment (generic scan tool for OBD).
In order to connect the special diagnostic equip­
ment, push the plug into the Data Link Connector
(DLC). The DLC is located to the right of the hood
release ¢
fig. 20.
Your authorized Audi dea ler or qualified work­
shop can interpret the code and perform the nec­
essary repair.
A WARNING
-~
Do not use the diagnostic connector for per­
sonal use. Incorrect usage can cause malfunc­
tions, which can increase the risk of a colli­
sion!
Electronic speed limiter
Your vehicle may be factory equipped with tires
that are rated for a maximum speed of 130 mph (210 km/h). This is less than the maximum speed
of your vehicle. To reduce the risk of sudden tire
failure and loss of control if the vehicle is operat­
ed at excessive speeds, your vehicle also has an
electronic speed limiter. The electronic speed
limiter prevents your vehicle from going faster
than the tire speed rating . For more information
¢ page 237.
If the engine control unit receives faulty vehicle
road speed signa ls, the Malfunction Indicator
Lamp (MIL)
¢4 will illuminate. If this occurs,
contact the nearest authori zed Audi dealer for
assistance.
SQS
Your vehicle's top speed is electronically limited
to 155 mph (250 km/h).
If the engi ne control unit receives fa ulty vehicle
road speed signals, the Malfunction Indicator
lllJ,,
23

Driver information system
Lamp (MIL) II will illuminate. If this occurs,
contact the nearest authorized Audi dealer for
assistance.
A WARNING
Always observe the posted speed limits and
adjust your speed to suit prevailing road, traf­
fic and weather conditions. Never drive your
vehicle faster than the maximum speed rating
of the tires installed.
Auto Check Control
Introduction
The Auto-Check control monitors the function of
certa in vehicle features and components. It sim­
ply makes sure these features and components
are working properly. The Auto-Check control
works as long as the ignition is on, as well as
whenever the veh icle is driven.
-
If a component is malfunctioning or if the need
for an urgent repair has been detected, this will
appear in the instrument cluster display. You will
also hear an audib le warning tone . The displays
are color coded in eit he r red or yellow depending
on their level of priority.
A red symbol means
Danger, a yellow symbol in­
d icates
Warning . In certain s ituations, informa­
tion message for the driver appea r in addition to
the red and yellow symbols .
Note about automatic transmission
The Auto -Check Control will automatically per­
form a test each time you switch on the ignition. W ith the selector lever in P or N, the fo llowing
message appears in the display:
When stationary apply brake pedal while select­
ing gear
When you select a different gear (for example: R, D, etc.), the message will disappear and the Au­
to-Check function is displayed.
If there is a malfunct ion, then the malfunction
message will appear about 15 seconds after you
start the vehicle. At the same time you will hear a
warn ing tone.
24
Driver information messages
Driver information messages are shown in the in­
strument cluster display in addition to symbols.
Fig. 21 Instrument cluste r: SET button
For example, if the transmission selector lever is
not in the P position when the engine is tu rned
off, the following message appears:
Shift to P otherwise vehicle can roll away. Doors
do not lock if lever is not in P.
The ign ition key can only be removed with these­
lector in this position. This and other messages
are brought up if a function cannot be carried
out.
Driver messages and red symbols
If a red symbol appears in the disp lay, a driver
message is also displayed automatically.
For example, the symbol for a problem with en­
gine o il pressure . appears in the display. The
follow ing message appears:
Turn off engine! Oil pressure too low
The driver message in the display goes out after
about 5 seconds. The driver message can be dis­ played again by briefly pressing the
I SETI button
r::> fig. 21.
Driver messages and yellow symbols
If a yellow symbol appears in the display, a driver
message is also displayed automatically.
For example, the symbol
a, appears in the dis­
play, indicating low windshie ld washer fluid level.
The following message also appears:
Please refill washer fluid II>-