a:,
a:,
...... N r--. N .... 0 0 ::, a:,
; Adaptive dampers
App lies to: vehicles with Audi drive select and suspension con
tro l
B Suspen sion: system fault !
There is an adaptive damper malf unction .
Drive to an aut hori zed Aud i dea le r o r a uthori zed
Audi Service Facility immediately to have the
malfunct ion corrected.
¢¢ Turn signals
If the II or i!I indicator light b links, the turn
signals are activated. If both indicator lights are
blinking, the emergency flashers are act ivated.
If an indicato r light blinks twice as fast as usua l,
a t urn signa l bulb has failed . Caref ully drive to an
author iz ed Audi dealer or author iz ed Audi Service
Facility immediately to have the malfunction cor
rected.
¢1.~ Trailer turn signal assembly
The indica to r li ght II blinks when the turn sig
n a l is used , if a traile r h as been p roperly connec t
e d to the veh icle .
If one of the turn s ignal bulbs on the trailer is
bu rned out or defect ive, the indicator l igh t will
n o t bl ink when yo u use the tu rn s ign als.
(D Tips
For ve hicles with a trail er hitch that was in
s talle d later accord ing to fa ctory spec ifica
ti ons, the trailer tur n signal as sembly is actu
at ed.
/fJl~/c:5 Door , hood or luggage
compartment lid is open
IJ-If the ind icator light tu rns on, then one of
the doors is not closed.
&-\-If the ind icator light t urns on, then the hood
is not closed .
§-j-If the ind icator light tu rns o n, then the lug
g age compartment lid is not closed .
Instruments and indicator lights
On Board Diagnostic
System (OBD)
Malfunction indicator lamp (MIL)
The ma lf u nction ind icator lamp (MI L) Ill in t he
inst rument cluste r is pa rt of the On Board D iag
nostic System (OBD II).
T he w arning/i ndic ator lig ht tu rn s o n when the ig
nition is switche d on and tu rns off once the en
gine is starte d and is running in idle at a stab le
speed. This indicates t hat the MIL is f unctioning
correctly.
If the light does not turn off after starting the
engine
or t urns on while driving, this may ind i
cate there is a malfunction in the eng ine. If the
i ndicator tu rns on, the catalytic conve rter may be
damaged .
Drive
with reduced engine performance (avo id
high speeds for extended periods of t ime and/o r
fast acceleration) and have the malfu nction cor
rected . See an author ized Audi dealer or author
ized Audi Service Facility .
The indicator may turn on if the e lectronic speed
limiter is faulty . For addit ional information, see
¢ page 18, Electronic speed limiter .
The MIL may also turn on if the fuel filler cap is
not closed correctly ¢
page 157.
On-Board Diagnostics
Fig. 5 Locat ion o f Data Link Connecto r (OLC)
On -Board Diagnostics mo nitors the components
of your emission control system . Each monitore d
I>-
17
Opening and clo sin g
Key set
Fig. 13 Your veh icle key set
I X CX) cc
@ Remote control key o r con venience k ey*
The convenience key is a remote control key with
special functions
c> page 26 and c> page 62.
W ith the remote control key, you can lock and
unlock the vehicle and start the engine . To fold
the key out and back in place, press the release button
c> fig. 13 -arrow-.
Repla cing a ke y
If a key is lost, see an authorized Audi dealer or
authorized Audi Service Facility . Have
this key de
activated .
It is important to bring a ll keys with
you .
If a key is lost, you should report it to your
insu rance company.
Numb er of k ey s
You can check the number of keys ass igned to
your veh icle in the instrument cluster d isplay . It
will show you this when you adjust the time
c> page 9. For examp le, the display 1/2 means
you are using vehicle key numbe r one out of two
keys total assigned to the vehicle. This way, you
can make sure that you have all the keys when
purchasing a used vehicle.
Electronic immobilizer
The immob il izer prevents una uthorized use of
the vehicle .
Under certain c ircumstances, the veh icle may not
be ab le to start if there is a key from a different
veh icle man ufact urer on the key cha in.
A WARNING
Always take the vehicle key with you when
leaving the vehicle, even for a short period of
24
time . This applies particularly when children
rema in in the vehicle. Otherwise the children
could start the engine or operate electrical
equipment such as power windows .
A WARNING
Applies to: vehicles with ignition lock
Do not remove the key from the ign it ion lock
until the vehicle has come to a complete stop.
Otherw ise, the steering lo ck could engage
suddenly and increase the risk of an accident.
@ Tips
- T he opera tion of the remote cont rol key can
be temporarily disrupted by interference
from transmitters in the v ic inity of the vehi
cle working in the same frequency range
(such as a ce ll phone or radio equipment).
- For an exp lanation on conformity with the
FCC regulations in the Un ited States and the
Industry Canada regulat ions, see
c> page 221.
LED and batteries in the remote control key
Fig . 14 Remot e con tro l key: LED
Fig . 15 Remote con tro l key : o pen in g th e cov er
Opening and clo sin g
-The vehicle can only be locked when these
l ector lever is in the P position (automatic
transmission).
- Do not use t he remote control when you are
inside the vehicle . Otherwise, you could un
i ntentionally lock the vehicle. If you then
tried to start the engine or open a door, the
a larm wou ld be triggered. If this happens,
press the
CD unlock button.
- Only use the panic funct ion in an emergen
cy.
Locking and unlocking with the
convenience key
A pp lies to : ve hicles w ith conven ience key
The doors and luggage compartment lid can be
unlocked/locked without using the remote con trol key.
F ig . 1 7 Doo r hand le: unlock ing/ lock ing senso r
Unlocking the vehicle
• To unlock the d river's or front passenger's door,
grab the door hand le of the respective door .
The door unlocks automatically.
• To open the door, pull the door hand le.
• To open the luggage compartment lid, press
the grip piece in the luggage compartment lid
c> page28.
Locking the vehicle
Requirement: the P selector lever position must
be engaged and all doors must be closed.
• To lock the vehicle, close the door an d touch
the sensor on the door handle
on ce c> fig. 17,
c> .&, . Do not hold the door hand le wh ile doing
this.
26
Un locking and locking the vehicle can o nly be
done at the front doors . The remote control key
cannot be more than approx imately
4 ft (1.5 m)
away from the door handle. It makes no differ
ence whether the master key is in your jacket
pocket or in your briefcase, for example.
The door cannot be opened for a brief period d i
rectly after locking it. This way you have the op
portunity to check if the doors locked correctly.
You can set in the Infotainment system if
only
the driver 's door or the entire vehicle should un
l ock when unlock ing
c> page 27. In vehicles
without an Infotainment system, you can unlock
the entire vehicle using se lective doo r unlocking .
_& WARNING
Read and heed all WARNINGS c> ,& in Descrip
tion on page 23.
(D Tips
If your vehicle is left standing for a long peri
od of t ime, note the following:
- The proximity sensor sw itches off after a
few days to
save ene rgy. You then have to
pull once on the door handle to unlock the
vehicle and a second time to ope n it.
- The energy management system gradually
tu rns off unnecessary convenience functions
to prevent the veh icle battery from drain ing
and to main tain the ve hicl e's ability to start
for as long as poss ible. You may no t be ab le
to unlo ck your veh icle using the conven ience
key.
- For an ex planation on co nfo rm ity w it h t he
FCC reg ulations in the Un ited States and the
I n dustry Canada regulations, see
c>poge 221.
Opening and clo sin g
_&. WARNING
Always take the veh icle key with you when
leaving the vehicle, even for a short period of
time. Th is applies particularly when children
remain in the vehicle . Othe rw ise children
cou ld start the engine or operate elect rical
equipment (s uch as power windows), w hich
increases the risk of an accide nt.
Power windows
Controls
The driver can control all power windows.
Fig. 29 Sect ion of dr ive r's doo r: controls
All power window switches are equ ipped with a
two-stage funct ion:
Open ing and clo sing the window s
.. To open or close the w indow completely , press
the switch down or pull the switch up br iefly to
the second level. The operation will stop if the
switch is pressed/pulled aga in.
• To select a position in between opened and
closed, press/pull the switch to the first leve l
u nt il t he desired window position is reached .
Power window switch es
(D Left front door
@ R ight front door
@ Left rear door
© R ight rear door
_&. WARNING
- Always take the vehicle key with you when
leaving the vehicle, even fo r a short per iod
of time. This applies particularly when chi l-
32
.
dren remain in the vehicle . Otherwise the
children could start the eng ine or operate
electrical equipment such as power win
dows, wh ich increases the risk of injury. The
power windows continue to function until
the dr iver's door or fro nt passenger's door
has bee n ope ned.
- Pay caref ul attention when clos ing the w in
dows. Pinching could ca use serio us inju ries.
- When locking the vehicle from outside, the
veh icle must be unoccup ied since the win
dows can no longe r be opened in an emer
ge ncy.
{1) Tips
After switching the ignition off, you can still
open and close the windows fo r approximate·
l y 10 m inutes. The power w indows do not
swi tc h off until the driver's door or fron t pas
senger's door has bee n opened.
Convenience opening /closing
All of the windows and the panorama roof can
be opened/closed at the same time.
Fig . 30 D river's door: door lock cyli nder
Con venience opening feature
• Hold the key in the open position@¢ fig. 30
until all of the windows are in the desired posi
tion and the panorama roof is tilted open.
Convenience closing feature
• Hold the key in the lock position @ unti l all the
windows and panorama roof are closed .
When the panor ama glass roof is opened/ closed,
the e lec tric s un shade is a lso opened/closed. .,..
Driving
Driving
General information
Breaking in
A new vehicle must be broken in, and the break in distance should be 1,000 miles (1,500 km).
For the first 600 miles (1,000 km), do not drive
at speeds that are more than 2/3 of the maxi
mum permitted RPM, avoid full acceleration and
do not tow a trailer. You may gradually start in
creasing the RPM and the speed between 600 miles (1,000 km) and 1,000 miles (1,500 km) .
During the first hours of use, the engine has a
higher internal friction than later on when all
moving parts have settled into place with each
other.
How the vehicle is driven during the first 1,000
miles (1,500 km) also affects the engine quality.
Drive at moderate engine speeds after the initial
break-in period, particularly when running a cold
engine . This will reduce engine wear and improve
the mileage .
Do not drive at too
low of an engine speed (rpm).
Shift down if the engine stops running "smooth ly". Extremely high engine speeds are automati
cally reduced .
Avoid damaging the vehicle
When you are driving on poor roads, or over
curbs, steep ramps , etc., make certain that low
lying parts such as spoilers and exhaust system
parts do not bottom out and get damaged.
This is especially true for vehicles with low-slung
chassis (sports chassis)* and fully loaded
vehicles.
Driving through water on roads
Note the following to reduce the risk of vehicle
damage when driving through water, for example
on flooded roads:
- The water must not be any higher than the bot
tom of the vehicle body.
- Do not drive faster than walking speed.
58
A WARNING ,_
After driving through water or mud, the effec
tiveness of the brakes may be reduced due to
moisture on the brake rotors and brake pads.
A few careful brake applications should dry
off the brakes.
([) Note
Vehicle components such as the engine,
transmission, suspension or electrical system
can be severely damaged by driving through
water.
(D Tips
- Determine the depth before driving through
water.
- Do not stop the vehicle, drive in reverse or
switch the engine off when driving through
water.
- Keep in mind that oncoming vehicles may
create waves that raise the water level and
make it too deep for your vehicle to drive
through safely.
-Avoid driving through salt water, because
this can cause corrosion.
Economical and environmentally-friendly
driving
The amount of fuel consumption, the environ
mental impact and the wear to the engine,
brakes and tires depends mostly on your driving
style . With an anticipatory and economic driving
style, fuel consumption can be reduced by ap proximately 10-15%. The following tips will help
you conserve the environment and your money at
the same time.
Anticipatory driving
A vehicle uses the most fuel when accelerating .
When you drive with anticipation, you do not need to brake as often and so you accelerate less.
When possible , let your vehicle coast with a gear
engaged, for example, when you notice that the
next traffic light is red. This produces an engine
braking effect, which helps to protect the brakes
and tires and reduces the emissions and fuel
...
00
00
......
"' ,....
"' ...... 0 0 :::,
00
consumption to zero (fuel shut-off during decel
eration).
Shift efficiently
An effective way to save fuel is to upshift earlier .
Staying in a gear too long uses fuel unnecessari
ly. Press down on the accelerator pedal slowly
and avoid "kick-down".
Avoid full acceleration
You should rarely travel at the maximum vehicle
speed. High speeds cause a disproportionately
high increase in fuel consumption, emissions and
traffic noise. Slower driving saves fuel.
Reduce idling time
There are benefits to stopping the engine, for ex
ample when at railroad crossings or traffic lights
with longer red lights. Stopping the engine for
30-40 seconds already saves more fuel than the
amount of extra fuel needed to restart the en
gine.
It takes a very long time in idle to warm the en
gine up to operating temperature . Wear and
emissions are especially high in the warm-up
phase. Therefore, you should begin driving im
mediately after starting the engine. Avoid high
RPMs while doing this.
Have maintenance performed regularly
By having maintenance performed regularly on
your vehicle, you can help to reduce fuel con
sumption before you even start to drive. The maintenance condition of your vehicle not only
affects traffic safety and long-term value but al
so impacts
fuel consumption. A poorly main
tained engine can lead to fuel consumption that
is 10% higher than normal.
Also check the
oil level when refueling. The oil
consumption
depends largely on the engine load
and speed . It is normal for the oil consumption
of a new engine to reach its lowest point only af
ter a certain amount of use. Therefore, the oil
consumption can only be properly judged after
approximately 3,000 miles (5,000 km) have been
driven.
Driving
Fewer short trips
The engine and catalytic converter have to reach
their optimal
operating temperature to reduce
fuel consumption and noxious emissions effec
tively.
Just after starting, a cold engine in a mid-size car
only achieves a fuel economy of 6-8 mpg
(30-40 l/100 km). After about a half a mile, fuel
economy climbs to 12 mpg (20 l/100 km). After
about 2.5 mi
(4 km), the engine is at its proper
operating temperature and fuel economy has
reached a normal level. So you can see that you
should avoid short trips whenever possible .
The
outside temperature is also critical in this re
gard. Your car consumes more fuel in the winter
than in the summer.
@ Note
Do not leave engine idling unattended after
starting. If warning lights should come on to indicate improper operation, they would go
unheeded. Extended idling also produces
heat, which could result in overheating or
other damage to the vehicle or other proper
ty.
(D Note
- Have your vehicle maintained properly and
in accordance with the service recommenda
tions in your Warranty & Maintenance book
let. Lack of proper maintenance as well as
improper use of the vehicle will impair the
function of the emission control system and could lead to damage.
- Do not alter or remove any component of
the Emission Control System unless ap
proved by the manufacturer.
- Do not alter or remove any device, such as
heat shields, switches, ignition wires,
valves, which are designed to protect your
vehicle's Emission Control System and other
important vehicle components .
(j) Tips
The consumption estimates as published by
ENVIRONMENTAL PROTECTION AGENCY
(EPA) and Transport Canada may not
59
Driving
correspond to you r actua l consumption on the
road, which will vary depending upon vehicle
load and speed, road and weather conditions,
trip length, etc.
Steering
Adjusting the steering wheel position
The steering column can be adjusted up and
down and forward and back.
F ig . 68 Lever u nde r the stee ring column
.,. Tilt the lever downward ¢ _A.
.,. Bring the steering wheel into the desired posi
tion .
.,. Press the lever upward again until it locks in
place .
.&_ WARNING
Improper use of steer ing whee l adjustment
and improper seating position can cause ser i
ous pe rsonal injury.
- Adjust the steering wheel column on ly when
the vehicle is not mov ing to prevent loss of
vehicle control.
- Adjust the driver's seat o r steering wheel so
that there is a minimum of 10 in (25 cm)
be tween your chest and t he s teering wheel
~ page 101, fig. 101 . If yo u cannot main
tain this minimum distance, the airbag sys
tem cannot protect you properly.
- If physica l limitations prevent you from sit
t ing 10 in (25 cm)
or more from the steer
ing wheel, check with your authorized Audi
dealer to see if adaptive equipment is avail
able .
- If the steering wheel is aligned with your
face, the supplemental driver's airbag can-
60
not provide as much protect ion in an acci
dent. Always make sure that the steer ing
wheel is aligned with your chest.
- Always hold the steering wheel with your
hands at the 9 o'clock and 3 o'clock posi
tions to reduce the risk of personal in jury if
the driver's airbag deploys .
- Never hold the steering wheel at the 12
o'clock position or with your hands inside
the steering wheel rim or on t he steering
wheel hub . Holding the steering wheel the
wrong way can cause serious in juries to the
h an ds, arm s and head if the drive r's airbag
deploys.
Starting and stopping
the engine (vehicles with an ignition lock)
Starting the engine
Applies to: vehicles wit h ignition lock
The ignition is switched on and the engine start
ed with the key in the ignition.
Fig. 69 Ign it ion lock : pos ition of the ig ni tio n key
Switching the ignition on/off
.,. To switch the ignition on, turn the ignition key
to position
(D .
.,. To switch the ignit ion off, turn the ignition key
to position @.
Starting the engine
.,. Press the brake pedal and move the selector
lever to the P or N posit ion.
.,. Turn the key to position @. The ignit ion key au
tomatically returns to posit ion
(D . Do not press
the accelerator peda l when doing this . ..,.
00
00
......
"' ,....
"' ...... 0 0 :::,
00
E quipment that uses a lot of electricity is switch
ed off temporari ly when you start the engine.
I f the engine does not start im mediately, stop
the s tart ing proced ure and repeat afte r 30 sec
onds. To restart the engine, t urn the ignition key
back to position @.
A WARNING
-Never allow the engine to run in confined
spaces -danger of asphyxiation .
- Never remove the ignition key from the igni
tion look while the vehicle is moving. Other
wise, the steering lock could suddenly en gage and you would not be able to steer the
vehicle .
- Always take the key with you whenever you
leave your vehicle. Otherw ise, the engine
could be started or electrical equ ipme nt
such as the power windows cou ld be operat
ed . T his can lead to serious injury.
- Never leave children or persons requiring as
sistance unattended in the vehicle. The
doo rs can be loc ked using the remote trans
mitter, preventing people from escap ing
from the vehicle on the ir own in the event o f
an emergency. Depend ing on the t ime of
year, peop le inside the vehicle can be ex
posed to very high or very low tempera
tures .
(D Note
Avoid high engine speed, full throttle, and
heavy engine load if the engine has not
reached operating temperature yet. You could
damage the engine.
@ For the sake of the environment
Do not let the engine run while parked to
warm up. Begin driving immediately . This re
duces unnecessary emissions.
(D Tips
- If it is difficu lt to turn the key to position
(D, turn the steering wheel back and forth
slightly to release the steering wheel lock .
- Some noise after starting the engine is nor
mal and is no cause for concern.
D riving
Stopping the engine
App lies to : vehicles wi th ignition lock
Stopping the engine
.,. Br ing the veh icle to a full stop.
.,. Tu rn the key to position @.
Engaging the steering lock
Requirement: the selector lever must be in P.
.,. Remove the ignition key in position @
¢ page 60, fig. 69 ¢ .&_.
.,. Turn the steering wheel until you hear the
steering whee l lock .
The locked steering helps prevent vehicle theft.
A WARNING ....._ --Never turn off the engine before the vehicle
has come to a complete stop. The full func
tion of the brake booster and the power
steer ing is not guaranteed. You must use
more force to turn or brake if necessary. Be
cause yo u cannot stee r and brake as you
usually would, th is could lead to crashes
and serious injuries .
- For safety reasons, you should always park
your veh icle w ith the selector lever in P.
Otherwise, the vehicle could inadvertently
ro ll away .
- The radiator fan can continue to run for up
to 10 minu tes even after you have turned
off the engine and removed the ignition key.
The radiator fan can also turn on again if the
engine coolant heats up because of intense
sunlight or heat build-up in the eng ine com
partment.
- Always take the key with you whenever you leave your vehicle. Otherwise, the engine
could be started or electrical equipment
such as the power windows could be operat
ed. This can lead to ser ious injury.
- Never leave children or persons requ iring as
sistance unattended in the vehicle . The
doors can be locked using the remote t rans
mitter, preventing people from escaping
from the vehicle on their ow n in the event of
an emergency . Depending on the time of
year, people inside the vehicle can be
61