2017 AUDI A8 infotainment

C) C0 ....
"' ,....
"' .... 0 0 :r driving. Never transport objects larger than
those which fit completely into the luggage area, because then the luggage compart­
ment lid cannot be fully closed .
- Never leave your vehicle unattended espe­
cially w ith the luggage compartment lid left
open . A child could crawl into the car
through the luggage compartment and pull
the lid shut, becoming trapped and unable
to get out. To reduce the risk of personal i n­
jury, never let children p lay in or around
your vehicle. A lways keep the luggage com­
partment lid as well as the vehicle doors
closed when not in use.
- Never close the luggage compartment lid
inattentively or without checking first. Al­
though the clos ing force of the l uggage
compartment lid is limited, you can st ill se­
riously injure yourself or others.
-Always ensure that no one is within range of the luggage compartment lid when it is
moving, in part icular close to the h inges and
the upper and lower edges -fi ngers or
hands can be pinched .
- Never try to interfere w ith the luggage com­
partment lid or help it when it is being
opened or closed automatically.
@ Tips
- The settings in the Infotainment system de­
termi ne if the luggage compartment lid ca n
be opened us ing the handle ~
page 32.
-When the vehicle is locked, the luggage
compartment lid can be unlocked separately
by p ressing the
l<=> I but ton on the remote
contro l key. The luggage compa rtment lid
l ocks automatically when it is closed again.
- You can close the luggage compartment lid
u sing the remo te c ontrol key (ve hicles w ith
convenience key *) up to a d ista nce of ap ­
prox ima tely 9 feet (3 m).
- The luggage comp artme nt lid can be ope r­
ated manually if the veh icle battery is low.
It is necessary to use more force when doing
th is . Move the lid slowly to reduce the
amount of force needed.
Op enin g an d clos ing
Opening the luggage compartment lid with
foot motion act ivation (kicking movement )
Applies to: vehicles with convenience key and sensor-control­
led luggage compartment lid
Fig. 32 Rear of the veh icle: foot movement
Requirements : you must be carrying your vehicle
key with you . You must be standing at the center
behind the luggage compartment lid . The dis ­
tance to the rear of the veh icle must be at least 8
in (20 cm). The ignition must be sw itched off.
Make s ure yo u have f irm footing .
"' Move your foot back and forth below t he bump­
er ~
fig. 32 . Do not touch the b umpe r. Once the
sys tem recogn izes the movement , the luggage
compa rtment l id will ope n.
T he luggage compartment lid will on ly open if
you make the movement as described . T his pre­
vents the luggage compa rtment lid from open ing
due to similar movements, s uch as when you
walk betwee n the rea r of the vehicle and your ga­
rage door.
General information
In some situ ations, the f unct io n may be lim ited
or tempora rily unavailable . T his may happen if:
- the l uggage compartment lid was closed imme ­
diately before .
- you park close to a hedge and the branches
move back and forth under the veh icle for a
long per iod of t ime .
-you clean your veh icle, for example with a pres­
sure washer or in a ca r wash .
- there is heavy ra in .
- the bumper is very dirty, for example after driv-
ing on salt-covered roads. ..,.
35

on the position of vehicles driving ahead and on­
coming vehicles, the vehicle speed and other en­
vironmental and traffic conditions.
Activating high beam assistant
Requirement: the light switch must be set to the
AUTO position and the high beam assistant must
be switched on in the Infotainment system
¢page 45.
.,. To activate the high beam assistant , tap the
lever forward @. T he
II indicator light ap­
pears in the instrument cluster display and the
high beam assistant is switched on/off auto­
matically. The
Ill indicator light also turns on if
the high beams are switched on.
Switching the high beams on/off manually
If the high beams did not switch on/off automat­
ically as expected, you may switch them on or off
manually instead:
.,. To switch the high beams on manually, tap the
lever forward @. T he indicator light
Ill turns
on .
.,. To switch the high beams off manually, pu ll the
lever back@. The h igh beam assistant is deac­
tivated.
Operating the headlight flasher
.,. To operate the headlight flasher when the high
beam assistant is activated and high beams are
switched off, pu ll the lever back @. The high
beam assistant rema ins active.
Messages in the instrument cluster display
Headlight assist: System fault!
Drive to an authorized Aud i dea le r or authorized
Aud i Service Facility immediately to have the
malfunction corrected. You can still switch the
high beams on or off manually.
Headlight assist: Unavailable No camera view
The camera view is blocked, for example by a
sticker or debris.
o The sensor is located between the interior rear­co
~ view mirror and the windshield. Do not place any ,..._
~ stickers in this area on the windshield.
0 0 :c ' Lights and Vision
A WARNING
High beam assistant is only intended to assist
the driver. The driver is still respons ible for
controlling the headlights and switching
them manua lly depending on light and visibi l­
it y conditions. It may be necessary to operate
them manually in situations such as:
- I n adverse weather conditions such as fog,
heavy rain, blowing snow or spraying water.
- On roads where oncoming traffic may be
pa rtia lly obscured, such as expressways.
- When there are road users that do not have
sufficient lighting, such as bicyclers or
vehicles with dirty tail lamps .
- I n tight curves and on steep hills.
- In poorly lit areas.
- W ith strong reflectors, such as signs.
- If the area of the w indshield near the sensor
is fogged over, dirty, icy or covered with a
sticker .
Adjusting the exterior lighting
The functions ore adjusted in the Infotainment
system .
.,. Select: !CAR ! function button > Car systems
control button > Vehicle settings > Exterior
lighting .
Automatic headlights
You can adjus t the following settings in the Au­
tomatic headlights
menu:
Headlights activation time -you can adjust if the
headlights switch on
Early, Medium or Late ac­
cording to the sensitivity of the light sensor.
Headlight assist* -you can switch the h igh beam
ass istant*
On and Off .
Daytime running lights*
USA models :
the daytime running lights can be
switched on/off. Select
On or Off.
Canada models:
this function cannot be switched
off. They activate automatically each time the ig -
nition is switched on .
ll>
45

0 co .... N ,..... N .... 0 0 :c ' reactivated the next time you switch the ignition
on.
C leaning the headlights. The headlight washer
system operates only when the low beam head­ lights are switched on.
If you move the lever to
position @, the headlights and the night vision
assist camera* are cleaned at intervals.
A WARNING
- The rain sensor is only intended to assist the
driver. The driver may still be responsible
for manually sw itching the wipers on based
on v is ibility conditions .
- The w indshield may not be treated with wa­
ter-repelling windsh ield coating agents . Un­
favorable conditions, such as wetness, dark­ ness, and when the sun is low, can cause in­
creased g lare, which increases the risk of an
acc ident. W iper blade chatter is a lso poss i­
ble.
- Prope rly f unction ing windsh ield wiper
blades are required fo r a clear view and safe
driving
c:> page 51, Replacing the wiper
blades.
(D Note
- If there is frost, make su re t he windshie ld
wiper blades are not fro zen to the wind­
shield. Sw itching on the windshield wipers
when the blades are frozen to the wind­
shield can damage the wiper blades.
- Prior to using a car wash, the windshield
wiper system must be switched
off (lever in
pos ition
@ ). This prevents the wipers from
switching on un intent ionally and causing
damage to the w indshield w iper system .
- The windshield wipers switch
off when the
i gnition is sw itched off. You can activate the
windsh ield wipers after the ign it ion is
switched back on by moving the winds hield
wiper lever to any posit ion.
- Worn o r dirty windshield wiper blades result
i n streak ing . This can affect the ra in sensor
funct ion. Check you r windshield wiper
blades regu larly.
Light s and Vision
-The washer fluid nozz les for the windshield
washer system are heated at low tempera­
t u res when the ign ition is on .
- When stopping tempo rari ly, such as at a
traffic light, the speed of the windshield
w ipers automatically reduces by one level.
Cleaning the wiper blades
Clean the wiper b lades when you see w iper
streaks . Clean the wiper blades with a soft towel
and glass cleane r.
.. Place the windshie ld w iper arms in the service
position
c:> page 51.
.. Fold the windshield w iper arms away from the
w indshield .
A WARNING
Dirty windshie ld wiper b lades can impa ir vi­
sion, wh ich increases the ris k of an acciden t.
Replacing the wiper blades
The service position is set in the Infotainment
system .
Fig. 57 Removing winds hield wiper b lades
Wind shi eld wiper se rvice po sition /b lade
r epl ace ment po sit ion
~
~
M 0 :i: ... m
.. Switch the ignition off and move the windshield
w iper lever to position @briefly
c::> page 50,
fig. 56. The windshield wipers move into the
serv ice position .
.. To br ing the wiper b lades back into the original
position, switch the ignition on and ope rate the
w indshield w iper lever.
You can also turn the service posit io n on or off in
the Infotainment system: ..,_
51

Sea ts and stor age
Seats and storage
General information
A WARNING
Refer to ¢ page 207, Driving safety for im­
portant information, tips, suggestions and
warnings that you should read and follow for
your own safety and the safety of you r pas­
sengers.
Front seats
Controls
Seat forward/back adjustment, seat height, backrest and seat cushion angle.
F ig. 60 Fr ont seat: adjust ing the seat
@ -Moving the seat forward/back: press the but ­
ton forward/back .
@ -Moving the seat up/down: press the button
up/down. To adjust the front seat cushion, press
the front button up/down. To adjust the rear seat
cushion, press the rear button up/down .
® - Switching the massage function* on/off . Se­
lect the type of massage with the multifunction
button
c:> page 54.
© - adjusting the backrest angle : press the but­
ton forward/back.
© -Comfo rt head restraint*
c:> page 58
@ -Mu ltifunction button* c:> page 54.
A WARNING
- The power front sea ts can also be adjusted
when the ign ition is switc hed off . For this
54
reason, children sho uld never be left unat­
tended in the vehicle - they could be injured!
- On ly adjust the front seat with when the ve­
hicle is stationary. Otherwise, this increases
the risk of an accident
- Exercise caution when adjust ing the seat
height. Unsupervised or careless seat ad­
justment can pinch fingers or hands causing in juries .
- The front seat backrests must not be re­
clined too far back when driving, because
this impa irs the effectiveness of the safety
belts and airbag system, which increases
the risk of inj ury.
Multifunction button
App lies to: vehicles wit h memory funct ion
You can adjust the massage function, upper sec­
tion of the backrest, lumbar support, side bol ­
sters, upper thigh support and safety belt height using the multifun ction button.
Fig . 61 Infota inment system : seat sett ings
Ope rating
.. If you turn the mult ifunct ion button @
c:> page 54, fig . 60 to the left or to the right,
the poss ible seat settings @are shown in the
Infotainment system
c:> fig. 61.
.. To select a seat setting, turn the multifunction
button @ in the corresponding direction until
the desired seat setting is outlined in red .
.. The arrows ® represent the possible adjust ­
ments . To lower the lumbar support, for exam­
ple, press the mult ifunct ion button @ down­
ward. The corresponding arrow © lights up.
The following seat settings @are poss ible: ..,_

Seat s and sto rage
Adju st ing lumbar support
.,. To a djust the cu rvature of the lumbar support,
press the b utton @to the left/right.
.,. To adj ust the he ight of the lumbar support,
press the button @upward/downward.
Adjusting th e head rest raint angle
.,. To adjust the head restraint so t hat it is more
vertical/more ang led, press the bu tton @ for­
ward/back.
Adjusting th e seat position
.,. To adjust the seat forward/back, press the but­
ton © forwa rd/back.
.,. To move the seat up/down, press t he button ©
upward/downward .
Adjusting the massage function *
.,. To adjust the "pulsating"/"wave" massage
funct ion, press the button © to the left/r ight.
T he massage f unction is at i ts strongest level
when three LEDs in the butto n turn on.
.,. To reduce the massage level, press the © but­
ton again .
.,. To switc h the massage function off, press the
button repeatedly until the L ED turns off.
Adju st ing th e re clining position
.,. To adjust the reclining position, press and hold
the button @ until the seat reaches its end po­
sition .
.,. Applies to vehicles with reclining seat*: if you
select the reclining position, the front passeng­
er's seat moves forward and the backrest re­
clines. Depending on the last setting, the leg
support may fold out at the same t ime . The
front passenger 's seat can no longer be used in
the re clining posit ion ¢..&, . You can adjust the
l eg suppo rt or fold the display fo rwa rd in the
reclining position.
Selecting the standard seat position
.,. To adjust the sta ndard seat pos it ion, press and
hold the button © unt il the seat reaches its
end posit ion .
.,. Applies to vehicles with reclining seat*: if you
select the standa rd sea t position, the fron t pas­
senger's seat moves back into the norma l posi-
56
tion, the head restraint moves to the upright
position and the leg support folds inward¢..&, .
Adjusting the d isplay*
.,. To t ilt the display fo rwa rd/bac k, press and hold
the left/r ight button @) until the d isp lay reach ­
es the des ired position .
.,. Applies to vehicles with reclining seat*: to
maintain a clear view of the road when the seat
is in the reclining pos ition, press and hold the
r ight button @) until the disp lay has folded for­
ward. Make sure the driver has a clear view of
the exter ior mirrors . If so, confirm the quest io n
in the Infotainment system w ith
Ye s. If you an­
swe r
No or do not respond to the q uest ion, the
disp lay w ill return to the up right pos ition.
Adju sting the leg support (vehicles with
reclining seat*)
Requirement: the reclining position must be se­
l ected
¢ page 56.
.,. To fold the leg support out/in, press and hold
the left/r ight button @ until the leg support
reaches the desired pos it ion.
.,. To angle the leg suppo rt so that it is more up­
r igh t/mo re reclined or to move it fo rward/back,
adj usting the front passenge r's sea t accord ing­
ly .
Adjusting the front passenger 's seat
.,. Make sure that the front passenger's seat ad­
jus tment is switc hed on in the Infotainment
system
¢ page 58 .
.,. To activate the front passenger's seat adjust ­
ment, press the button ®·
.,. To adjust the front passenger's seat forward/
back, press the button © forward/back.
.,. To move the front passenger's seat up/down,
press the button © upward/downward.
.,. To adjust the front passenger's seat backrest so
that is more upright/more recl ined, press the
button @ forward/back .
.,. App lies to ve hicles with reclin ing seat*: to ad­
just the reclin ing/standard sea t position, press
and hold the b utton @!© unt il the front pas -
senger's seat reaches its end position. .,.

C) C0 ....
"' " "' .... 0 0 :r A WARNING
-The power seats can also be adjusted when
the ignition is switched off. For this reason,
children should never be left unattended in
the vehicle - they could be injured!
- Be careful when ad justing the seat. Unsu­
pervised or careless seat adjustment can
pinch fingers o r hands ca using injur ies.
- Applies to vehicles with reclining seat*:
- Do not use the fron t passenger's seat for
seating when it is in the reclining position .
This increases the risk of serious injury or
death.
- Never adjust the reclining position when
the front passenger 's seat is occupied.
This increases the risk of injury.
- Do not tilt the display if the driver's view
of the right exterior mirror w ill be ob ­
structed .
- Make sure the area between the leg sup­
port and the front passenger 's seat back­
rest is clear before folding the leg support
in so that you are not pinched.
(D Tips
- The massage function switches off auto ­
matically after approx imately 10 minutes.
- If you
cannot ad just the reclining seat * or
the front passenger's seat from the rear, it is possible that:
- t he front passenger's seat memory fu nc­
t ion is swi tched off~ page
59, or
- the c hild safety lock is switched on (the~
button ~ page 37 or the right
T button
~ page 37 is turned on in the dr iver's
door), o r
- the front passenger seat adjustment is
switched off in the Infotainment system
~ page
SB.
Seats and storag e
Massage function remote control
Applies to: vehicles with reclining seat and massage function
Fig. 66 Remote cont rol: rec lin ing seat massage functions
The remote controls are located in the rear cen­
ter console ¢ page 62, fig. 72 . The massage
funct ion is only ava ilable when the ignition is
switched on.
.,. To open the remote control compartment,
press the left button and fold the center arm­
rest upward .
.,. To adjust the massage type, press the appropr i­
ate button @·@ . The LED in the button turns
on .
.,. To adjust the speed/inte nsity, turn the thumb­
wheel @I® . The LEDs indicate the speed/in­
tensity.
.. Press the selected massage type again to
sw itch the massage function off.
Massage types
@ -Wave
@ -Pul sating
© -Stretch
@ -Lumbar
(D Tips
- The massage function switches off auto ­
matically after approximate ly 10 minutes .
- If you activate a massage type aga in, the
last selected intensity and speed will be se­
lected .
57

Seats and storage
Comfort settings
Applies to: vehicles with comfort seats in the rear
You con also apply several settings for the rear
using the Infotainment system in the cockpit.
• Se lect in the MMI: !CAR ! function button> Car
systems
control button > Vehicle settings >
Seats > Rear seats .
Adjust to normal position -
with this function,
the outer rear seats and the front passenger's
seat are moved to the factory setting.
Easy seat entry -the Easy seat entry makes it
possible to enter and exit the rear seats comfort ­
ably. If the function is sw itched on, the rear seat
automatically moves all the way back when t he
corresponding door is opened .
Passenger's seat adjustment* -if the function is
switched on in the Infotainment system, the
front passenger's seat can also be adjusted from
the rear seat using the ¢
page 55, fig. 64 but­
tons .
The front passenger's seat cannot be adjusted, if
- the front passenger's seat memory function is
switched off¢
page 59.
-the ~ button tur ns on in the driver's door
¢page 37.
-The right[!] button turns on in vehicles with
power child safety locks *
¢page 37.
Head restraints
Adjusting the head restraints
Fig. 67 Comfo rt hea d rest raint: ad just ing t he side bo lste rs
58
Fig. 68 Outer rea r seat: adjus ting the head restra int
Adjust the head restraints so the upper edge is as
even as possible with the top of you r head . If tha t
i s not possible, try to adjust as close to this posi­
tion as possible.
Adjusting the front head restraints
.,. To adjust the he igh t of the front head re­
straints, pull/press the button ©
9 page 54,
fig.
60 up/down.
.,. To adjust the side bolsters*, push the side bol­
sters in to the desired position ¢
fig. 67.
• Vehicles with reclining seat*: grab the head re­
straint at the sides with both hands and slide
the head restraint up/down until it clicks into
place .
Adjusting the rear head restraints
The center head restraint in the rear is not ad­
justable. When passengers ride in the outer rear
seats, raise these head restraints up to the top position ¢
,&.
• To move the head restra int up, hold it at the
sides with both hands and slide it upward until
you feel it click into place .
.,. To move the head restraint down, press the
button (small arrow) ¢
fig. 68 and slide the
head restraint downward.
8,_ WARNING
- Always read and follow the applicab le warn­
ings
¢page 210.
-Driving with the head restraints not in the
upright position increases the r isk of se rious
lnJUry .
~

Sea ts and stor age
The memo ry buttons are located in the driver's
door, front passenger's door and in the rear
doors*.
Sw itch ing the mem ory function on /off
• Press the IOFF I button to switch the memory
funct ion on/off. The LE D in the button tu rns on
when the memory function is
off. Seat profiles
are neither stored nor recalled.
Storing a seat pr ofi le
• Press the ISE TI button. When the wo rd S ET
ligh ts up, the memory is ready to store set ­
tings .
• Now press a memory button briefly . A tone
confirms that the settings were stored .
Accessing a seat profile
• If the drive r's door is open and the ig nit ion is
swi tched off, press the memory b utton .
• If the driver's door is closed or the ignition is
switched on , press and ho ld the memory but­
ton until the seat adjustment is comp lete.
A WARNING
- For safety reasons, the seat setting can only
be recalled when the vehicle is stationary,
otherw ise there is a risk of an accide nt.
- If necessary, you can stop the recall process
by pressing the
I OFF! button or any memory
button.
Adjusting the front passenger 's seat in the
Infotainment system
Applies to: vehicles with memory function
The driver can move the front passenger's seat
into various positions .
Adjusting the front p assenge r's seat from
th e drive r's s eat
• Select : the ICARI function button> C ar s ystem s
contro l button > Veh icle sett ing s > Seats >
Pas senger's seat > Adju st seat po sition .
• You can now adjust the front passenger's seat
u sing the driver's seat but tons
c=;, page 54,
fig . 60.
60
Align with driver's seat
• To transfer the settings from the dr iver's seat
to the front passenge r's seat , se lect: the
!CAR I
function button > Car s ystems cont rol button >
Vehicle settings > Se ats > Pa ssenger 's sea t >
Align with dri ver 's s eat .
• Press and hold the control knob until the ad­
justing process is comp lete.
@ Tips
The lumbar support and upper thigh support
settings are not transferred when aligning
the front passenger's seat with the driver's
seat.
12 volt sockets
Applies to: vehicles with sockets
Fi g. 70 S ide compart ment in l ugg age compartment: 12
vo lt soc ket•
Fig . 71 Exa mple of a rear ce nter con so le: 12 vol t socket
The 12-vol t sockets can be used for e lectr ica l ac­
cessories . The power consumption at the out let
must not exceed 120 watts.
There is an add itional 12 volt so cket in the center
console
c=;, page 63, fig. 75 . ..,.