2017 AUDI A6 display

co
co
.... N
" N .... 0 0 <.,;) 'SI"
Driver information
system
Overview
Fig . 4 Dr iver informa tion system in t he inst rum ent clus ter
Fig . S Ins trum ent cl uster: examp le in formation line
The information in the driver information system
is shown in @ tabs @¢
fig. 4. The following
content is possible depending on vehicle equip­
ment:
® ®
First tab Vehicle functions :
On-board computer
¢page22
Efficiency program*
¢page 23
Digital speedometer
Cru ise control system*
¢ page86
Adaptive cruise control* and braking
guard*
¢ page88
Act ive lane assist*
¢page96
Reduced display
Driver in forma tion system
® ®
Second Indicator lights and messages
tab Warning when a door, the hood or
the rear lid is not closed
Service interval display
¢ page208
Speed warning system*
¢page86
Third tab Night vision assistant*
¢page 101
Fourth Audio/Video
t ab
Fifth tab Telephone*
Sixth tab Navigation*
The second and third tabs are only visible if at least one indicator light or message is shown or if
that system is switched on.
The status line © is located in the bottom part of
the display ¢
fig. 4. It displays the exterior tem­
perature, time, selector lever position, tripod­
ometer and odometer.
For some vehicle functions, you can access the
trip information from the temporary memory
¢
page 23 in line @¢ fig. 5 .
A WARNING
Do not assume the roads are free of ice based
on the outside temperature display. Be aware
that there may be ice on roads even when the
outside temperature is around 41 °F ( +5 °C)
and that ice can increase the risk of accidents.
(i} Tips
-You can select the units used for tempera ­
ture, speed and other measurements in the
Infotainment system .
- If your vehicle is stationary or if you are driv­
ing at very low speeds , the temperature dis­
played may be slightly higher than the ac­
tual temperature outside due to the heat ra­
diating from the eng ine.
- For info rmation on the audio/video and nav­
igation* functions, refer to the separate In­
fotainment system owner's manual.
21

Driver information system
Operation
The driver information system is operated using
the buttons on the multifunction steering wheel.
Fig . 6 Mult ifunctio n steerin g wheel: operating the driver
i nfor matio n system
Fig. 7 Instr ume nt cluster : ope ning the vehicle functions
menu
Operating
• Switch the ign ition on.
• To swi tch betwe en the tabs, press the rocker
swi tch @to the left or r igh t
c::> fig. 6.
• To acce ss addition al in form ation be low or
above, turn the thum bwhee l@ down o r up.
• To confi rm a selection, press the t humbwheel
@.
• To open the submenu fo r an active tab, press
the b utton
l:il @.
• To select a function prog rammed to a steering
wheel butto n*, press t he bu tton @.
Opening the Vehicle functions
• Se lect t he fir st tab with the rocker switch (D .
• Press t he [ii button @ . The Vehicle functions
menu is displayed c::> fig. 7.
• To se lect a menu item, turn and press t he
th umbwheel @.
22
Resetting values to zero
• In the Vehicle functions menu, sele ct On­
board computer or Efficien cy program .
• You ca n now select between the long -term
memory a nd short -term memory .
• To reset the va lues in a memo ry , press and hold
the t humbwh eel @ for one second.
Assigning a function to a programmable
steering wheel button*
• Select the I CAR ! funct ion button > (Car )*Sys­
tems
contro l butto n > Vehicle settings > Steer ­
ing wheel button programming .
The last function selected disp lays when you
switch the ignition on.
On-board computer
Fig. 8 Instrument cluster: fu el cons umptio n display
You can ca ll up t he fo llowi ng in fo rmat io n in the
o n-board compu ter:
- Da te
- Driv ing t ime from the short-te rm memory
- Average consumption from the short-term
memory
- Averag e speed from the short -term memory
- Distance d rive n from the short-term memo ry
- Curre nt fuel consumption
- Shor t-te rm memory overv iew
- Lo ng-te rm memory o verv iew
The short-te rm memory collects driving informa­
tion from the time the ig nition is switched on un­
ti l it is switch ed off . If you continue driving w ith­
i n two hours after sw itchi ng t he ig nition off, t he
new values are include d w hen c alcula ting t he cu r-
rent t rip inform ation.
Ill>-

co
co
.... N
" N .... 0 0 <.,;) 'SI'
Unlike the short-term memory, the long -term
memory is not erased automatica lly. Yo u can se­
l ect the time period for evaluat ing trip informa ­
tion yourself .
F or some veh icle functions, you can access the
driving information from the short -term memory
i n the
line @¢poge21, fig. 5.
Fuel consumption
The cu rrent fue l co nsu mption c an be shown us ­
i ng a ba r g rap h
¢fig . 8 . The aver age consum p­
tion stored in the short -term memory is also dis­
p layed . If the bar is green, your vehicle is saving
fuel throug h one of the following functions:
-Re cuperation : electr ical ene rgy can be store d in
the vehicle battery when t he vehicle is coasting
or driving downhill. The bar will move toward
0 .
-Cylinder on demand system* : the engine auto­
matically switches four cylinde rs off when low­
er powe r output is required and other condi­
tions are met. This change is not noticeab le to
t h e passengers.
(]} Tips
The date, time of day and t ime and date for­
mat can be set in the Infotainment system
¢page 24.
Efficiency program
Applies to: ve hicles with effic ie ncy p rogram
F ig. 9 In str ume nt cluste r: ot her equ ipment
Driver in forma tion system
Fig. 10 Instrument cluster: econo my t ip
T he eff ic iency p rogram can help you to use less
fuel. It shows o ther cons umers th at are using
f uel and e co nomy tip s give a dvice on how to drive
efficie ntly. The eff ic ien cy pr ogr am receives dis­
tance and consumption data from the on -board
computer.
To dis play the eff icien cy p rogram, o pen the
Vehi ­
cle functions
m enu and select the Efficiency pro­
gram
menu item.
Other consumers
The Energy con sumers view lists other equip­
ment that is c urren tly affe cting f ue l cons ump­
tio n. Th e displ ay shows up to three o ther eq uip­
ment items @¢
fig. 9. The equipment using the
most power is listed first. If more than three
items using power are switched on, the equip­
ment that is current ly using the most power is
displayed.
A ga uge @ also shows the c urrent tota l con­
s u mption of all othe r consumers.
Economy tips
In c ertai n sit ua tio ns, economy tips appe ar auto­
ma tic ally for a short t ime in the e ffic iency pro­
gram
¢ fig . 10 . If you follow these economy tips,
yo u can red uce your vehicle's fuel cons umption.
T o turn an e cono my tip off immedia tely afte r it
appea rs, p ress any button o n the mu ltifun ction
stee ring wheel.
© Tips
- If you era se the d ata in t he eff ic ien cy pr o­
gram, t he v alues in the on -boar d compu te r
wi ll also be reset .
23

Driver information system
-Once you have turned an economy tip off, it
will only appear again after you turn the ig­
nit ion on again .
- The economy tips are not displayed in every
instance, but rather in intervals over a peri­
od of t ime .
Odometer
Fig. 11 Inst rume nt cluster : odometer and reset butto n
The display of d istance dr iven is shown in miles
"m i" or kilometers "km". The units of measure­
ment (kilometers/m iles) can be changed in the
I nfotainment system.
Trip odometer and odometer
The trip odometer shows the distance driven
since it was last reset . It can be used to measure
short distances.
The trip odometer can be reset to zero by press­
ing the ~ reset button.
The odometer shows the total distance that the
veh icle has been driven.
Malfunction indicator
If there is a malfunction in the instrument clus­
ter,
DEF will appear in the trip odometer display.
H ave the malfunction corrected as soon as possi­
ble.
Time/date display
The date, time of day and time and date format
can be set in the Infota inment system. Refer to
the Infota inment system operating manual for
instructions .
24
When you open the driver's door, the date and
time appear in the instrument cluster display for
30 seconds .
Head-up display
Applies to: vehicles with Head-up Display
Fig. 12 Example: indicators in the Head -up display
Fig. 13 Instrument panel: knob for t he head -up di splay
The Head-up display projects certain warn ings or
selected information from the assist systems* or
navigation* on the windshield. The display ap­
pears within the driver's field of vision.
Switching on/off
"" To switch the head-up dis play on or off, press
the knob~
q fig. 13.
Adjusting the height
The height of the d isplay can be adjusted to the
i ndividual driver.
"" Make sure you are seated correctly
qpage 129.
"" Turn the knob~ to adjust the display.
Settings in the Infotainment system
""Select: the I CARI function button > (Car)* Sys-
tems
contro l button > Driver assistance > .,.

Hea d-u p di spl ay> Head- up di spla y conten ts or
Displ ay brigh tn ess.
Di spla y content
In the Infotainment system, you can specify
which information should be displayed: For ex­
ample, th is can include navigation informat ion *,
Adaptive cruise control* or night vision assist*.
The display of certa in info rmation and some of
the red indicator lights cannot be h idden in the
I nfotainment system.
Displ ay brightness
You can adjust the display br ightness in the Info­
tainment system. The display brightness decreas­
es automatically as the amount of light decreas­
es. The backgro und brightness is adjusted with
the instrument il lumination
c::> page 44 .
(D Note
To prevent scratches on the g lass cove ring the
head- up d isplay, do not place any objects in
the projection opening.
(D Tips
- Sunglasses w ith polar izat ion fi lters and u n­
favorab le lighting conditions can have a
negative effect on the display.
- An optim um display depends on the seat
pos ition and the height adjustment of the
head -up display.
- A specia l windshield is needed for the head ­
up display function.
- Fo r information on cleaning, refer to
c::> ta­
ble on page 233.
On Board Diagnostic
System (OBD)
Malfunction Indicator Lamp (MIL)
The Malfunction Ind icator Lamp (MIL) a in the
instr ument cluster is part of the On-Board Diag­
nostic (OBD II) system.
~ The warning/indicator light i lluminates when the ....
~ ign it ion is switched on and goes ou t after the en-N .... 0 0 <.,;) 'SI"
Driver info rm atio n sys tem
gine starts and the idle has stab ilized. This indi­
cates that the MIL is working properly.
If th e light does not go ou t after the eng ine is
sta rted, or i llum inates while you are driving, a
malfunction may exist in the engine system. If
the light illuminates, the catalytic converter
could be damaged.
Cont inue driving
with redu ced p ower (avoiding
sustained high speeds and/or rapid accelera­
tions) and have the condition corrected. Contact
your authorized Audi dealer.
If the ligh t illum ina tes, the electronic speed lim­
iter may also be malfunctioning. For more infor­
mation
c::> page 26, Electronic speed limiter.
An impro perl y close d fuel fi ller cap may al so
ca use the
MIL li g ht to illuminate c::> page 192.
On-Board Diagnostics
Fig. 14 Locat ion of Data L ink Connector (DLC)
On-Board Diagnostics monitors the components
of your emission control system. Each monitored
component in your engine system has been as­
s igned a code . In case of a malfunction, the com­
ponent will be identified and the fault stored as a
code in the contro l module memory.
T he M IL light may also illum inate if there is a
leak in the on-board fuel vapor recovery system.
If the light i lluminates after a refuelling, stop
the vehicle and make sure the fue l filler cap is
properly closed
c::> page 192.
In order to make an accurate diagnosis, the stor ­
ed data can only be displayed using special diag-
nostic equipment (generic scan tool for OBD).
IJI,-
25

Valet Parking function
Applies to: veh icles wit h Valet Parking function
The valet parking function protects the luggage
comportment from unauthorized access .
Fig. 34 Glove compartment: valet park ing function button
You can switch the valet parking function on, for
example when someone else is parking your vehi­
cle
l)_ When the function is switched on, the ve­
hicle can be driven, locked and unlocked using
the master key, but access to the luggage com­
partment is not permitted .
.,. Remove the integrated mechanical key
r::!:>poge 29.
.,. Open the glove compartment.
.,. Press the
IVALET I button to switch the valet
parking function on. The LED in the button
turns on.
.,. Lock the glove compartment with the mechani­
cal key .
.,. Applies to vehicles with lockable backrests in
t h e rear: to also secure the luggage compart­
ment from the vehicle inter ior, lock the backr­
ests using the mechanica l key ¢
page 57.
.,. Only giv e the remote control key to the service
personnel parking your car and keep the re­
moved mechanical key with you.
The following buttons are deactivated when the
va let parking function is switched on:
- 1""' 1 button in the driver's door
-la l button on the remote control key
- Handle in the rear lid
When the valet parking function is switched on,
co ~ the message Valet parking activated appears in
N
" N .... 0 0
~ ll This func tion is not available in all co untries .
Open ing and closing
the instrument cluster display when you switch
the ignition on.
(D Tips
Please note that the luggage compartment
can still be accessed from the vehicle interior
in vehicles with a pass-through, even when
the valet parking function is switched on .
Garage door opener
(Homelink)
Description
Applies to: veh icles with garage door opener (Home link)
Fig . 35 Garage door opene r: examples of usage for diffe r­
ent systems
With the garage door opener (Homelink), you
can activate systems such as the garage doors ,
security systems or house lights from inside your
vehicle. Three buttons a re integrated in the head ­
liner that can be programmed to up to three re­
mote controls.
To be able to operate systems using the garage
door opener, the buttons in the headliner must
first be programmed .
_&. WARNING
When operating or programming the garage
door opener, make sure that no people or ob­
j ects are in the area immediate ly surrounding
the equipment. People can be injured or prop-
erty can be damaged if struck when closing. .,.
39

Opening and closing
@ Tips
-For security reasons, we recommend that
you clear the programmed buttons before
selling the vehicle.
- For additional information about Homelin k,
vis it www.homelink.com.
- For an explanation on conformity with the
FCC regulations in the United States and the
Industry Canada regulations, see
¢page 262.
Programming buttons
App lies to : vehicles with garage door opener (Homelin k)
Fig. 36 Headli ner: co ntrols
You can program both fixed code and rolling code
systems using this procedure.
Programming/reprogramming buttons
,.. Switch the ignition on.
,.. Press and hold the button in the headliner that
you wou ld like to program for at least 10 sec­
onds . Or
,.. Select:
-I C_A _R_I function button > (Car)* Systems
control button > Vehicle settings > Garage
door opener > Program garage door opener .
,.. Fo llow the instructions in the Infota inment sys­
tem .
Deleting button programming
The programmed buttons cannot be de leted indi­
vidually. They must be deleted all at once. Repro­
gram the buttons if necessary.
,.. Se lect : the
ICARI function button > (Car)* Sys­
tems
control button > Vehicle settings > Ga­
rage door opener
> Clear program settings >
Yes.
40
Displaying the version/status/country code
,.. Select: !CAR I func tion button > (Car)* Systems
control button > Vehicle settings > Garage
door opener > Version information.
(D Tips
The garage door opener may need to be
synchronized with the system motor after the
programming. Follow the manufacturer's in­
str uctions for doing this.
Operation
Applies to : vehicles with garage door opener (Homelink)
Requirements: the button in the headliner must
be programmed
¢ page 40 and the veh icle must
be within range of the system, such as the ga rage
door .
.,. Press the button to open the garage door. The
LED @¢
page 40, fig. 36 blinks or turns on .
.,. Press the button aga in to open the garage
door .
(D Tips
When opening or closing the garage door, do
not press and hold the button longer ten sec­
onds or the garage door opener will switch to
programming mode.

Lights and Vi sion
- If you turn off the ignition whi le the exterior
lights are on and open the door, a warning
tone sounds.
- In cool or damp weather, the inside of the
headlights, turn signals and tail lights can
fog over due to the temperature d ifference
between the inside and outside. They will
clear shortly after sw itch ing them on. This
does not affect the serv ice life of the light­
ing .
Turn signal and h igh beam lever
The turn signal lever operates the turn signals,
the high beams and the headlight flasher.
F ig . 38 Turn sig nal and high beam lever
Tu rn signals ¢ Q
N
0 ,.._
9 J:
;;!;
The turn s ignals activate when you move the lev­
er into a turn signal position when the ignition is
switched on.
@ -right turn signal
@ -left turn s ignal
The turn signal blinks three times if you tap the lever (conven ience turn signal).
High b eams and h eadlight flasher ~D
Move the lever to the corresponding position :
@ -high beams on (veh icles w ith H igh beam as­
sistant*
¢ page 42)
© -high beams off or headlight flasher
The
II indicator light in the instrument cluster
turns on.
42
A WARNING , _
H igh beams can cause glare for other drivers,
which increases the risk of an accident . For
this reason, only use the high beams or the headlight flasher when they will not create
g la re fo r othe r drive rs .
High beam assistant
App lies to: vehicles wi th high beam ass istan t
A camera on the rearv iew mirror mou nt can de­
tect light sources from other road use rs. The high
beams switch on or off automatically depending
on the position of vehicles driving ahead and on­
coming vehicles, the vehicle speed and other en­
vironmental and traffic cond itions.
Activating high beam ass istant
Requirement: the light sw itch must be set to the
A UTO posit ion and the hig h beam ass istant must
be switched on in the Infotai nment system
¢ page 43 .
.,. To act ivate the high beam ass istant, tap the
lever forward @. The
El indicator light ap­
pears in the instrument cluster display and the
high beam headlights are sw itched on/off auto­
matically . The
II indicator light also turns on if
the high beams are switched on.
Switching the high b eam s on /off manually
If the high beams did not switch on/off automat ­
ica lly as expected, yo u may switch them on or off
manually instead:
.,. To switch t he h igh beams on manually, tap the
lever forward @. The
II indicator light turns
on.
.,. To switch the h igh beams off manua lly, pull the
lever back@. The high beam assistant is deac­
tivated .
Operating the headlight flasher
.,. To operate the headlig ht flasher when the high
beam assistant is activated and hig h beams are
sw itched off, pull the lever back@. The high
beam ass istant remains active.