2017 AUDI A5 CABRIOLET warning light

Instruments and indicator lights
cooling system -you could damage your en­
gine .
~- Steering column lock
• Steering defe cti ve! Do not dri ve vehicle!
If the indicator lig ht t urns on and the message
appears, there is an electronic steering column lock malf unction . You cannot switch the ignition
on.
Do
not tow your vehicle because i t cannot be
steered. Seek professional assistance.
£II S te erin g lo ck: C ontact dealer!
If t he indicator light turns on and the message
appears, there is an electro nic steer ing colum n
lock malfunct ion.
Drive to your authori zed Aud i dea ler immediately
to have the malfunct ion corrected.
A WARNING
Your vehicle must not be towed in the eve nt
of a malfunction i n the elect ronic steering
co lumn lock be ca use it cannot be steered d ue
t o the locked steering. If it is towed wi th t he
steering locked, the re is the r isk of an acci ­
dent .
0-Ignition lock
• Ignit ion lock defecti ve. Contact dealer!
If the indicator lig ht tu rns on and the message
appears, do
not switch the ign ition off because
you may not be ab le to switch it on again .
D rive to you r autho rized Aud i dea le r i mmedia tely
to have the malf unct ion corrected.
On ve hicles w ith convenience key*, the engine
should not be switched off using the
I S T AR T ENG IN E STOP I button because the en­
g ine ca nnot be sta rted again after the ignition
has been switched off .
(D Tips
The symbol's appearance mig ht be diffe re nt
in some mode ls .
16
!;. J[/; Electronic Stabilization Control (ESC)
If the bJ ind icator light blinks while driving , the
ESC o r ASR (A nti-Sl ip Regulation) is act ively regu­
l ating .
If the
bJ ind icator light turns on, the system has
switched the ESC off. In t his case, you can switch
t h e ign it io n off and then on to swi tch the ESC on
again. The indicator light t urns off when the sys­
tem is functioning fu lly .
If the . indicator light turns on, ESC was re­
stri cted or sw itched off using the
I.$ O FF I butto n
qpage 167 .
Stabilization cont rol (ESC / ABS ): Fault! See
owner' s manual
If the indicator l ight DJ and the ABS indicator
li ght
[IlJ (USA models) ;El] (Canada mode ls)
turn o n and the message appears, the ABS or
electron ic different ial lo ck is malfunctioning.
This also causes the ESC to malfunc tion. The
brakes st ill function with the ir norma l power, but
ABS is not active .
D rive to your au thori zed Audi dealer immediate ly
to have the malfunc tion cor rected .
Fo r more info rmation about the ESC
q page 167 .
A WARNING
If the 11111 (USA models)/ . (Canada mod­
e ls) br ake system indicator light turns on to­
gether with the ABS and ESC ind icator lights,
the ABS/ESC regulating function may have
failed. F unctions that stabilize the vehicle are
no longer ava ilab le. This could cause the vehi­
cle to swerve and increase the risk of sliding. Drive carefully to the nearest authorized Aud i
dealer and have the malfunction corrected .
(D Tips
For additional informat ion on ESC and ABS,
r efer to
q page 167.

a:,
a:,
...... N r--. N ...... 0
0
LL 00
ABS /(@) Anti-lock braking system (ABS)
This warning/indicator light monitors the ABS
and the electronic differential lock (EDL) .
The warning/indicator light fIE) (USA models)/
ti] (Canada models) will come on for a few sec­
onds when the ign it ion is switched on. The light
will go out after an automatic check sequence is
comp leted.
There is a malfunction in the ABS when:
-The warning/indicator light does not illuminate
when you switch the ign it ion on .
- The warning/indicator light does not go out af­
ter a few seconds.
- The warning/indicator light illuminates while driving .
The ESC indicator light a lso illuminates if there is
a ma lfunction in the ABS. The message
Stabiliza­
tion control (ESC): Fault! See owner's manual
also appears in the instrument cluster display
and a warning tone sounds.
The brake system will still respond even with­
out the assistance of the ABS system. See your
authorized Audi dealer as soon as possible to re ­
store full braking performance.
For more infor­
mat ion regarding the ABS
r=;,page 167.
Malfunction in the brake system
If the brake warning light r:::;, page 13 and the ABS
warn ing illuminate
together there may be a mal­
function in the ABS, and there may also be a ma l­
function in the brake system itself
q .&. . The ABS
will not work and you will notice a change in
braking respon se and performance.
In the event of a malfunction in the brake sys ­
tem
the warning/indicator light 1111 (USA mod­
els)/ . (Canada models) in the instrument clus­
ter f lashes
r:::;, page 13 .
Malfunction in the electronic differential
lock (EDL)
The ED L works together with the ABS . The ABS
warn ing light will come on if there is a ma lfunc­
tion in the EDL system
~ page 167 . See your au­
thorized Audi dealer as soon as possible.
Instruments and indicator lights
A WARNING
- If the fIE) (USA models)/ tl] (Canada mod­
els) warning light does not go out, or if it
comes on while dr iv ing, the ABS system is
not working proper ly . The vehicle can then
be stopped only with the standard brakes
(without ABS). You will not have the protec­
tion ABS provides. Contact your authorized
Audi dealer as soon as possible.
- USA models: If the 1111 warning light and
the
9 warning light come on together, the
rear wheels could lock up first under hard
braking. Rear wheel lock-up can cause loss
of vehicle control and an acc ident. Have your
veh icle repaired immediately by your au­
thorized Audi dealer or qualified workshop .
Drive slowly and avoid sudden, hard brake
applications .
-Canada models: If the brake warn ing light
• and the ABS warning light
tlJ come on
together, the rear whee ls could lock up first
under hard b raking. Rear whee l lock-up can
cause loss of vehicle control and an acci­
dent . Have your vehicle repaired immediate­
ly by your authorized Audi dea ler or quali­
fied workshop. Drive slowly and avoid sud­
den, hard brake applications.
t!i I !i: Safety systems
The fl (USA models)/ EI (Canada mode ls) indi­
cator light monitors the safety systems (e.g. a ir­
bags, pretensioners) and illum inates for a few
seconds each time you switch the ignition on.
If the
II (USA models) tEI (Canada models) in­
dicator light does not go out, or if it illuminates
wh ile you are driving, or if it starts to blink, then
there is a malfunct ion somewhere in the system .
If the light does not illuminate when you switch
the ignition on, this also means there is a mal­
function.
A WARNING ~
If yo u have a ma lf u nction in the safety sys-
tems, contact your authorized Aud i dealer im­
mediately. Otherwise the safety systems may
not work properly in an accident.
17

Instruments and indicator lights
(0) Worn brake pads
IJ Brake pads!
If the warn ing light illum inates, immed iate ly
contact your authorized A ud i dealer o r qualified
wo rkshop to have all brake pads inspected. O n
USA models the wa rni ng lig ht
Ei] comes on to ­
gethe r wi th the war ning l igh t
1111 . Both sets of
b rake pads on an ax le m ust always be rep lace d at
the same time .
A WARNING
Driv ing with bad bra kes can ca use a co llision
and ser ious personal in jury.
- If the wa rning light
Ei] and the warning
light
11111 ) w ith the message Brake pads !
comes on in the instrument cl uster display,
i mmediately contact your author ized Audi
dealer or qualified workshop to have all
bra ke pads checked o r rep laced if necessary.
EPC Electronic power control
This warning/indicator light monitors the elec­
tronic power control .
-
The~ warni ng/indicator light (Electronic Powe r
Control) ill uminates when you switch the ign ition
on as a function check.
(D} Tips
If this wa rning/in dicator light ill uminates
wh ile you are driving, then there is a mal func­
tion in the eng ine electron ics. Have the ma l­
function corrected as soon as possib le by yo ur
author ized A udi dealer or a qualified repair fa­
cility .
o Malfunction Indicator Lamp (MIL)
The Malfunc tion Ind ica tor Lamp (M IL) is part of
the On-Boa rd Di ag nosti c (O BD II) system. The
symbo l
('4 lights up whe n the ignition is swi tch ­
e d on and wi ll turn off after the engine has sta rt·
e d and has sett led at a constant idle speed . This
i n dicates that the MIL is working p roperly.
l) - : USA mode ls onl y
18
The wa rning lig ht ill uminates w hen the re is a
malfunction in the engine electronic system.
Contact yo ur aut ho rized Aud i dea le r and have the
malfunction corrected .
An impro per ly closed fue l filler cap may also
ca use the MIL light to ill uminate ¢
page 190 .
For more info rm ation c::> page 2 5.
!?>i Engine speed limitation
App lies to : vehicles wi th engine speed limitatio n
II! Do not exceed max. engine speed of XXXX
rpm
The II! symbo l illu min ates when the re is an en­
gine co ntro l ma lf u nct ion. The~ indica tor ligh t
in the instrument clus ter also illum ina tes . T he
engine spee d is limited to the s peed displayed in
the d river info rmation system. Keep in mind t hat
the engine speed w ill not exceed the value dis ­
played in the driver information system, for ex­
amp le w hen downshifting.
D rive to your authorized A udi dealer immediate ly
to have the mal function cor rected .
~ ... Engine oil sensor
• Oil level! Sensor defective
If the symbol illuminates, contact your author ­
i zed Audi dealer and have the oil sensor inspect­
ed . Until yo u have this done, chec k the oi l level
each time you refuel just to be on the safe side
¢ page 197.
Eli) Tank system
fiD Please refuel
If the indicato r light turns on for the first time
and t he message appea rs, the re are about
2.1 -2.4 gallons (7 • 9 lite rs) of fuel left in the
ta nk. Time to refuel ¢
page 190 .
fiD Fuel tank system malfunct ion! Contact deal -
er ..,.

a:,
a:,
...... N r--. N ...... 0
0
LL 00
If the indicator light turns on and this message
appears, there is a malfunction in the tank sys­
tem.
Drive to your authorized Audi dealer immediately
to have the malfunction corrected.
C> Windshield washer flu id level
B Please refill washer fluid
If the symbol illuminates, add windshield washer
fluid to the washer system and also to the head­
light washer system*
~ page 206.
~ Windshield wipers
El Windshield wiper defective
There is a malfunction with the windshield wip­
ers.
Drive to your authorized Audi dealer immediately
to have the malfunction corrected.
~I }D10$ Defective light bulb warning
If the S:I indicator light turns on, a bulb has
failed. The message indicates the location of the
bulb.
- If the Im indicator light also turns on, then a
fog light has failed. The position of the indica­
tor light corresponds with the location on the
vehicle.
- If the II indicator light also turns on, then a
rear fog* light has failed. The position of the in­
dicator light corresponds with the location on
the vehicle.
This warning can also occur if the light switch is
in an unengaged position between two symbols.
Vehicle lights: System fault!
If the message appears, there is a malfunction in
the headlights or light switch.
Drive to your authorized Audi dealer immediately
to have the malfunction corrected.
Instruments and indicator lights
A WARNING
-Light bulbs are pressurized and could ex­
plode while they are being changed causing
serious personal injury.
-
- Work with due care when handling the high­
voltage section of gas discharge (xenon)
lights*. Failure to do so could result in death
or serious injury.
@ Tips
Have the bulb replaced or the connection re­
paired by your authorized Audi Service depart­
ment.
§.0 Headlight range control
Applies to: vehicles with headlight range control
II Headlight range control defective !
If the symbol II illuminates, the dynamic head­
light range control is no longer working properly.
Have the system checked and repaired at your au­
thorized Audi dealer.
go Adaptive Light
Applies to: vehicles with adaptive light
rlJ Audi adaptive light: defective
If the indicator light turns on and this message
appears, there is a malfunction in the adaptive
light system. The headlights still function.
Go to an authorized dealership to have the head­
lights or the control unit for the adaptive light re­
paired.
@. o Light/rain sensor
Applies to: vehicles with light/rain sensor
El Automatic headlights/ automatic wipers
defective
If the indicator light turns on and this message
appears, the light/rain sensor is not functioning
correctly.
For safety reasons the low beams are turned on
permanently with the switch in
AUTO. However, .,.
19

Instruments and indicator lights
you can continue to turn the lights on and off us ­
ing the light switch . You can still control a ll func­
tions that are independent of the rain sensor
through the w indshield wiper lever.
Contact your author ized Audi dealer as soon as
possible to have the problem corrected.
; Adaptive dampers
Applies to: veh icles with Audi drive select and adaptive damp·
ers
B Su spen sion : S yst em fault!
If the B symbol in the display comes on, there is
a ma lf u nction in the adaptive dampers . P lease go
to an author ized Audi dealer or qu alified work­
shop to have the ma lfunction repaired .
J--: Sport differential
Applies to: vehicles with Audi drive select and sport differen ·
tial
Sport differ ential: Syst em fault!
There is a malfunction with the sport differential.
Drive to your authorized Aud i dea ler immediately
to have the malfunct ion corrected.
Sport differ ential: Overhe ating
The transmiss ion tempe rature has increased s ig­
n ificant ly due to the sporty driv ing manne r. D rive
i n a less sporty manner until the temperature re­
turns to the normal range and the indicator light
switches of.
A WARNING
Contact your authorized A udi dealer or quali­
fied workshop if the sport differential is fau lty
or ma lfunctioning. The repa ir must be per­
formed by trained personnel us ing the correct
oil in order to ensure safety .
~ Ignition lock
l3 Ignition lock defective
There is a malfunction in the electronic ignition
lock . Please go to an authorized Audi dea ler or
other qualified workshop to have the malfu nction
repaired .
20
¢ Q Turn signals
Wheneve r yo u use the left B or the right Ill
turn s ignal , the ind ic a tor light blinks. When you
u se the emergency flashe rs, both indicator ligh ts
f lash.
If one of the tu rn signa l ligh t bulbs bu rn out, the
turn s ignal will b link t wice as fast as no rmal.
Caref ully drive to yo ur a uth o rized Aud i dea ler im­
mediate ly to have the malfunction corrected.

a:,
a:,
...... N
" N ...... 0
0
LL co
Driver information
system
Introduction
The Driver information display inside the instru­
ment cluster provides you, the driver, with im­
portant information.
Fig. 7 Instrument cluster: ce nter display
Fig. 8 Wipe r lever: contro ls for the menu display
Center display
With the ignition on, the display in th e Driver In­
formation System shows the following informa­
tion :
- CD* inserted or Radio* station set
- Outs ide temperature*: At temperatures below
41 °f (+S
0
(), a snowflake symbol appears in
front of the temperature display¢ ,1,. .
- Warning if one of the doors, front lid or engine
compartment lid is not closed.
Additional functions
You can open the following functions in the Driv­
er Information System display by pressing the
I RESETI button¢ fig. 8 one or more t imes :
Digital speedometer*
Tire pressure monitoring*
¢pag e224
Driver in forma tion system
Trip computer ¢page22
Efficiency program* ¢page24
Service interval display ¢page25
Speed warning ¢page 78
Gearshift selector posit ions Au -i=>page 81
tomatic transm ission
Adaptive cruise control*
¢ page 88
Auto Check Control
Some functions and vehicle components are
scanned for their operating status when you
switch the ignition on and while you are driving. Malfunctions or required service procedures are
signaled audibly and indicated by red and yellow
illum inated symbols and reminders in the dis­
play.
A WARNING
--
- Never rely exclus ively on the outside tem­
pe rature display to determine if a road sur­
face is icy or not. Keep in m ind that road
surfaces, especially bridges and overpasses,
could be ice covered and slippery even at an
outside temperat ure above 41 °f (+S °C).
- Always remember, even if the "snowflake"
symbol (ice warning) does not appear in the
display, black ice could be on the road.
- Always reduce your speed and dr ive with
specia l care in cold weather conditions when
the chance of encountering icy road surfaces
increases.
(j) Tips
If the vehicle is stationary, or if you are driv­
ing at a very low speed, the temperature
shown in the disp lay might be slightly higher
than the actual outside temperature. This is
caused by the heat being radiated from the
engine.
21

messages appear automatically and are only dis­
p layed in the efficiency program. The fuel econo­
my messages turn off a utomat ically after acer ­
tain period of time.
.. To turn a fuel economy message off immedi ­
ately after it appears, press the I RESE T I button
¢ page 23, fig. 11 @, or
.. Press the function select ion switch ¢
page 23,
fig. 11
@ .
(D Tips
-Once you have turned a fuel economy mes­
sage off, it will on ly appear again after you
turn the ignit ion on again.
- The fuel economy messages are not dis­
played in every instance, but rather in inter­
vals over a period of t ime .
Service interval display
The service interval display reminds you when
your next service is due .
The schedule for the next oil change or inspec­
tion is calculated automatically and displayed ac ­
cord ingly . The display works in two stages :
Service rem inder
30 days before the next service is due, a service
reminder appears in the d isp lay when you turn on
the ignition.
After about 5 seconds the display switches back
to normal. The distance and time remain ing are
updated each time the ignition is turned on until
the date due for service is reached.
Se rvi ce due
When the due date for service is reached, the
m essage
Ser vice due! appears in the instrument
cluster immediately after you turn on the igni ­
tion . Additionally, a warning tone sounds. After
about 5 seconds the d isplay sw itches back to nor ­
mal.
Call ing up the servic e schedules
a:,
a:,
...... If or when an oil change or inspection is due, can N
~ be shown in the radio or MM!* d isplay by select-,.....
8 ing the serv ice interval d isplay in the car menu. LL 00
Dri ver informa tion system
Select I CAR I funct ion but ton > Se rvice i nterval
di spla y
or ICARI function button > Car systems *
control button > Ser vicing & checks.
Resetting the service int erval display
Yo ur autho rized Aud i dea le r will reset the co rre­
sponding serv ice schedu le after performing the
appropriate service on your vehicle . You also have
the possibility to reset the oi l change schedule
after having performed an oil change accord ing
to Audi specifications. SelectlCAR lfunction but­
ton
> Ser vice inter val display > Re set oil change
int erval
or ICARI function button > C ar systems *
control button > Se rvi cing & checks > Re set oil
change inter val.
(D Note
- Only reset the oil change display when you
have completed an o il change.
- If you disconnect the battery term inals, no
calcu lations can be made for the se rvice in­
terva l display dur ing th is time and no serv­
i c e rem inder will appear. Remembe r that
observ ing the proper serv ice i ntervals is vi­
t ally impo rtan t to ex tending the life o f your
vehicle, particular ly the engine, and ma in­
taining its va lue . Even if the mileage driven
is low, the maximum period o f one yea r
from one service to the next must not be ex­
ceeded.
(D Tips
The information in the Serv ice Reminder re­
mains stored even when the vehicle battery is
disconnected.
On Board Diagnostic
System (OBD)
Malfunction Indicator Lamp (MIL)
The Malfunction Indicator Lamp (MIL) ¢4 in the
instrument cluster is part of the On-Board Diag­
nostic (OBD II) system .
The warning/indicator light ill uminates when the
ignition is sw itched on and goes out after the en­
gine starts and the idle has stab ilized . This indi-
cates that the MIL is working properly . ..,.
25

Driver information system
If the light does not go out after the engine is
started, or illuminates whi le you are driving, a
malfunct ion may exist in the engine system. If
the light illuminates, the catalytic converter
could be damaged.
Continue driving
with reduced power (avoiding
sustained high speeds and/or rapid accelera­
tions) and have the condition corrected. Contact
your authorized Audi dealer.
If the light illuminates, the electronic speed lim­iter may a lso be malfunctioning. For more infor­
mation
c:> page 26, Electronic speed limiter.
An improperly closed fuel filler cap may also
cause the MIL light to illuminate
c:> page 190.
On-Board Diagnostics
Fig. 15 Loca tion of Data Li nk Connector (D LC)
On-Board Diagnostics monitors the components
of your emission control system. Each monitored
component in your engine system has been as­
signed a code . In case of a malfunction, the com­
ponent will be identif ied and the fau lt stored as a
code in the control module memory.
The MIL light may also illuminate if there is a
leak in the on-board fuel vapor recovery system .
If the light illuminates after a refueling, stop the
vehicle and make sure the fue l filler cap is prop­
erly closed
c:> page 190 .
In order to make an accurate diagnosis, the stor­
ed data can only be displayed using special diag­
nostic equipment (generic scan tool for OBD).
In order to connect the specia l diagnostic equip­
ment, push the plug into the Data Link Connector
(DLC). The DLC is located to the right of the hood
release
c:> fig. 15.
26
Your authorized Audi dea ler or qual ified work­
shop can interpret the code and perform the nec­
essary repair.
_& WARNING
Do not use the diagnostic connector for per­
sonal use. Incorrect usage can cause malfunc­
tions, which can increase the risk of a colli­
sion!
Electronic speed limiter
-
Your vehicle may be factory equ ipped w ith tires
that are rated fo r a maximum speed of 130 mph
(210 km/h). This is may be less than the maxi­
mum speed of your vehicle. To reduce the risk of
sudden tire failure and loss of control if the vehi­
cle is operated at excessive speeds , your vehicle
has an e lectronic speed limiter. The electronic
speed limiter prevents your vehicle from going
faster than the tire speed rating . For more infor­
mation
c:> page 207.
If the engine control unit receives faulty vehicle roadspeed signals, the Malfunction Indicator
Light (MIL)
II will illuminate. If this occurs, con­
tact the nearest authorized Audi dealer for ass is­
tance .
_& WARNING
Always observe the posted speed limits and
adjust your speed to suit prevailing road, traf­
fic and weather conditions. Never drive your
vehicle faster than the maximum speed rating
of the tires insta lled .
-