2017 AUDI A5 CABRIOLET engine

Instruments and indicator lights
cooling system -you could damage your en­
gine .
~- Steering column lock
• Steering defe cti ve! Do not dri ve vehicle!
If the indicator lig ht t urns on and the message
appears, there is an electronic steering column lock malf unction . You cannot switch the ignition
on.
Do
not tow your vehicle because i t cannot be
steered. Seek professional assistance.
£II S te erin g lo ck: C ontact dealer!
If t he indicator light turns on and the message
appears, there is an electro nic steer ing colum n
lock malfunct ion.
Drive to your authori zed Aud i dea ler immediately
to have the malfunct ion corrected.
A WARNING
Your vehicle must not be towed in the eve nt
of a malfunction i n the elect ronic steering
co lumn lock be ca use it cannot be steered d ue
t o the locked steering. If it is towed wi th t he
steering locked, the re is the r isk of an acci ­
dent .
0-Ignition lock
• Ignit ion lock defecti ve. Contact dealer!
If the indicator lig ht tu rns on and the message
appears, do
not switch the ign ition off because
you may not be ab le to switch it on again .
D rive to you r autho rized Aud i dea le r i mmedia tely
to have the malf unct ion corrected.
On ve hicles w ith convenience key*, the engine
should not be switched off using the
I S T AR T ENG IN E STOP I button because the en­
g ine ca nnot be sta rted again after the ignition
has been switched off .
(D Tips
The symbol's appearance mig ht be diffe re nt
in some mode ls .
16
!;. J[/; Electronic Stabilization Control (ESC)
If the bJ ind icator light blinks while driving , the
ESC o r ASR (A nti-Sl ip Regulation) is act ively regu­
l ating .
If the
bJ ind icator light turns on, the system has
switched the ESC off. In t his case, you can switch
t h e ign it io n off and then on to swi tch the ESC on
again. The indicator light t urns off when the sys­
tem is functioning fu lly .
If the . indicator light turns on, ESC was re­
stri cted or sw itched off using the
I.$ O FF I butto n
qpage 167 .
Stabilization cont rol (ESC / ABS ): Fault! See
owner' s manual
If the indicator l ight DJ and the ABS indicator
li ght
[IlJ (USA models) ;El] (Canada mode ls)
turn o n and the message appears, the ABS or
electron ic different ial lo ck is malfunctioning.
This also causes the ESC to malfunc tion. The
brakes st ill function with the ir norma l power, but
ABS is not active .
D rive to your au thori zed Audi dealer immediate ly
to have the malfunc tion cor rected .
Fo r more info rmation about the ESC
q page 167 .
A WARNING
If the 11111 (USA models)/ . (Canada mod­
e ls) br ake system indicator light turns on to­
gether with the ABS and ESC ind icator lights,
the ABS/ESC regulating function may have
failed. F unctions that stabilize the vehicle are
no longer ava ilab le. This could cause the vehi­
cle to swerve and increase the risk of sliding. Drive carefully to the nearest authorized Aud i
dealer and have the malfunction corrected .
(D Tips
For additional informat ion on ESC and ABS,
r efer to
q page 167.

Instruments and indicator lights
(0) Worn brake pads
IJ Brake pads!
If the warn ing light illum inates, immed iate ly
contact your authorized A ud i dealer o r qualified
wo rkshop to have all brake pads inspected. O n
USA models the wa rni ng lig ht
Ei] comes on to ­
gethe r wi th the war ning l igh t
1111 . Both sets of
b rake pads on an ax le m ust always be rep lace d at
the same time .
A WARNING
Driv ing with bad bra kes can ca use a co llision
and ser ious personal in jury.
- If the wa rning light
Ei] and the warning
light
11111 ) w ith the message Brake pads !
comes on in the instrument cl uster display,
i mmediately contact your author ized Audi
dealer or qualified workshop to have all
bra ke pads checked o r rep laced if necessary.
EPC Electronic power control
This warning/indicator light monitors the elec­
tronic power control .
-
The~ warni ng/indicator light (Electronic Powe r
Control) ill uminates when you switch the ign ition
on as a function check.
(D} Tips
If this wa rning/in dicator light ill uminates
wh ile you are driving, then there is a mal func­
tion in the eng ine electron ics. Have the ma l­
function corrected as soon as possib le by yo ur
author ized A udi dealer or a qualified repair fa­
cility .
o Malfunction Indicator Lamp (MIL)
The Malfunc tion Ind ica tor Lamp (M IL) is part of
the On-Boa rd Di ag nosti c (O BD II) system. The
symbo l
('4 lights up whe n the ignition is swi tch ­
e d on and wi ll turn off after the engine has sta rt·
e d and has sett led at a constant idle speed . This
i n dicates that the MIL is working p roperly.
l) - : USA mode ls onl y
18
The wa rning lig ht ill uminates w hen the re is a
malfunction in the engine electronic system.
Contact yo ur aut ho rized Aud i dea le r and have the
malfunction corrected .
An impro per ly closed fue l filler cap may also
ca use the MIL light to ill uminate ¢
page 190 .
For more info rm ation c::> page 2 5.
!?>i Engine speed limitation
App lies to : vehicles wi th engine speed limitatio n
II! Do not exceed max. engine speed of XXXX
rpm
The II! symbo l illu min ates when the re is an en­
gine co ntro l ma lf u nct ion. The~ indica tor ligh t
in the instrument clus ter also illum ina tes . T he
engine spee d is limited to the s peed displayed in
the d river info rmation system. Keep in mind t hat
the engine speed w ill not exceed the value dis ­
played in the driver information system, for ex­
amp le w hen downshifting.
D rive to your authorized A udi dealer immediate ly
to have the mal function cor rected .
~ ... Engine oil sensor
• Oil level! Sensor defective
If the symbol illuminates, contact your author ­
i zed Audi dealer and have the oil sensor inspect­
ed . Until yo u have this done, chec k the oi l level
each time you refuel just to be on the safe side
¢ page 197.
Eli) Tank system
fiD Please refuel
If the indicato r light turns on for the first time
and t he message appea rs, the re are about
2.1 -2.4 gallons (7 • 9 lite rs) of fuel left in the
ta nk. Time to refuel ¢
page 190 .
fiD Fuel tank system malfunct ion! Contact deal -
er ..,.

a:,
a:,
...... N
" N ...... 0
0
LL co
Driver information
system
Introduction
The Driver information display inside the instru­
ment cluster provides you, the driver, with im­
portant information.
Fig. 7 Instrument cluster: ce nter display
Fig. 8 Wipe r lever: contro ls for the menu display
Center display
With the ignition on, the display in th e Driver In­
formation System shows the following informa­
tion :
- CD* inserted or Radio* station set
- Outs ide temperature*: At temperatures below
41 °f (+S
0
(), a snowflake symbol appears in
front of the temperature display¢ ,1,. .
- Warning if one of the doors, front lid or engine
compartment lid is not closed.
Additional functions
You can open the following functions in the Driv­
er Information System display by pressing the
I RESETI button¢ fig. 8 one or more t imes :
Digital speedometer*
Tire pressure monitoring*
¢pag e224
Driver in forma tion system
Trip computer ¢page22
Efficiency program* ¢page24
Service interval display ¢page25
Speed warning ¢page 78
Gearshift selector posit ions Au -i=>page 81
tomatic transm ission
Adaptive cruise control*
¢ page 88
Auto Check Control
Some functions and vehicle components are
scanned for their operating status when you
switch the ignition on and while you are driving. Malfunctions or required service procedures are
signaled audibly and indicated by red and yellow
illum inated symbols and reminders in the dis­
play.
A WARNING
--
- Never rely exclus ively on the outside tem­
pe rature display to determine if a road sur­
face is icy or not. Keep in m ind that road
surfaces, especially bridges and overpasses,
could be ice covered and slippery even at an
outside temperat ure above 41 °f (+S °C).
- Always remember, even if the "snowflake"
symbol (ice warning) does not appear in the
display, black ice could be on the road.
- Always reduce your speed and dr ive with
specia l care in cold weather conditions when
the chance of encountering icy road surfaces
increases.
(j) Tips
If the vehicle is stationary, or if you are driv­
ing at a very low speed, the temperature
shown in the disp lay might be slightly higher
than the actual outside temperature. This is
caused by the heat being radiated from the
engine.
21

messages appear automatically and are only dis­
p layed in the efficiency program. The fuel econo­
my messages turn off a utomat ically after acer ­
tain period of time.
.. To turn a fuel economy message off immedi ­
ately after it appears, press the I RESE T I button
¢ page 23, fig. 11 @, or
.. Press the function select ion switch ¢
page 23,
fig. 11
@ .
(D Tips
-Once you have turned a fuel economy mes­
sage off, it will on ly appear again after you
turn the ignit ion on again.
- The fuel economy messages are not dis­
played in every instance, but rather in inter­
vals over a period of t ime .
Service interval display
The service interval display reminds you when
your next service is due .
The schedule for the next oil change or inspec­
tion is calculated automatically and displayed ac ­
cord ingly . The display works in two stages :
Service rem inder
30 days before the next service is due, a service
reminder appears in the d isp lay when you turn on
the ignition.
After about 5 seconds the display switches back
to normal. The distance and time remain ing are
updated each time the ignition is turned on until
the date due for service is reached.
Se rvi ce due
When the due date for service is reached, the
m essage
Ser vice due! appears in the instrument
cluster immediately after you turn on the igni ­
tion . Additionally, a warning tone sounds. After
about 5 seconds the d isplay sw itches back to nor ­
mal.
Call ing up the servic e schedules
a:,
a:,
...... If or when an oil change or inspection is due, can N
~ be shown in the radio or MM!* d isplay by select-,.....
8 ing the serv ice interval d isplay in the car menu. LL 00
Dri ver informa tion system
Select I CAR I funct ion but ton > Se rvice i nterval
di spla y
or ICARI function button > Car systems *
control button > Ser vicing & checks.
Resetting the service int erval display
Yo ur autho rized Aud i dea le r will reset the co rre­
sponding serv ice schedu le after performing the
appropriate service on your vehicle . You also have
the possibility to reset the oi l change schedule
after having performed an oil change accord ing
to Audi specifications. SelectlCAR lfunction but­
ton
> Ser vice inter val display > Re set oil change
int erval
or ICARI function button > C ar systems *
control button > Se rvi cing & checks > Re set oil
change inter val.
(D Note
- Only reset the oil change display when you
have completed an o il change.
- If you disconnect the battery term inals, no
calcu lations can be made for the se rvice in­
terva l display dur ing th is time and no serv­
i c e rem inder will appear. Remembe r that
observ ing the proper serv ice i ntervals is vi­
t ally impo rtan t to ex tending the life o f your
vehicle, particular ly the engine, and ma in­
taining its va lue . Even if the mileage driven
is low, the maximum period o f one yea r
from one service to the next must not be ex­
ceeded.
(D Tips
The information in the Serv ice Reminder re­
mains stored even when the vehicle battery is
disconnected.
On Board Diagnostic
System (OBD)
Malfunction Indicator Lamp (MIL)
The Malfunction Indicator Lamp (MIL) ¢4 in the
instrument cluster is part of the On-Board Diag­
nostic (OBD II) system .
The warning/indicator light ill uminates when the
ignition is sw itched on and goes out after the en­
gine starts and the idle has stab ilized . This indi-
cates that the MIL is working properly . ..,.
25

Driver information system
If the light does not go out after the engine is
started, or illuminates whi le you are driving, a
malfunct ion may exist in the engine system. If
the light illuminates, the catalytic converter
could be damaged.
Continue driving
with reduced power (avoiding
sustained high speeds and/or rapid accelera­
tions) and have the condition corrected. Contact
your authorized Audi dealer.
If the light illuminates, the electronic speed lim­iter may a lso be malfunctioning. For more infor­
mation
c:> page 26, Electronic speed limiter.
An improperly closed fuel filler cap may also
cause the MIL light to illuminate
c:> page 190.
On-Board Diagnostics
Fig. 15 Loca tion of Data Li nk Connector (D LC)
On-Board Diagnostics monitors the components
of your emission control system. Each monitored
component in your engine system has been as­
signed a code . In case of a malfunction, the com­
ponent will be identif ied and the fau lt stored as a
code in the control module memory.
The MIL light may also illuminate if there is a
leak in the on-board fuel vapor recovery system .
If the light illuminates after a refueling, stop the
vehicle and make sure the fue l filler cap is prop­
erly closed
c:> page 190 .
In order to make an accurate diagnosis, the stor­
ed data can only be displayed using special diag­
nostic equipment (generic scan tool for OBD).
In order to connect the specia l diagnostic equip­
ment, push the plug into the Data Link Connector
(DLC). The DLC is located to the right of the hood
release
c:> fig. 15.
26
Your authorized Audi dea ler or qual ified work­
shop can interpret the code and perform the nec­
essary repair.
_& WARNING
Do not use the diagnostic connector for per­
sonal use. Incorrect usage can cause malfunc­
tions, which can increase the risk of a colli­
sion!
Electronic speed limiter
-
Your vehicle may be factory equ ipped w ith tires
that are rated fo r a maximum speed of 130 mph
(210 km/h). This is may be less than the maxi­
mum speed of your vehicle. To reduce the risk of
sudden tire failure and loss of control if the vehi­
cle is operated at excessive speeds , your vehicle
has an e lectronic speed limiter. The electronic
speed limiter prevents your vehicle from going
faster than the tire speed rating . For more infor­
mation
c:> page 207.
If the engine control unit receives faulty vehicle roadspeed signals, the Malfunction Indicator
Light (MIL)
II will illuminate. If this occurs, con­
tact the nearest authorized Audi dealer for ass is­
tance .
_& WARNING
Always observe the posted speed limits and
adjust your speed to suit prevailing road, traf­
fic and weather conditions. Never drive your
vehicle faster than the maximum speed rating
of the tires insta lled .
-

Opening and clo sin g
- If the power locking system should fail, you
can still open the fuel tank flap in an emer­
gency ¢
page 192.
-You are well advised not to keep val uables
inside an unatte nded vehicle, v is ible or not.
Even a properly locked vehicle cannot pro­
v ide the security of a safe.
- If the LED in the upper edge of the driver's
door panel comes on for about 30 seconds
after t he vehicle is locked, there is a mal­
funct ion in the power lock ing or the anti­
theft warning system . Have the malf unct io n
cor rected by an authorized Audi dealership
or q ualified repair facility.
Key set
F ig . 16 Key set
m 0 ±
~
@ Remote control key with mechanical key
You can centrally lock and unlock your veh icle
and start the engine w it h the master key with re­
mote cont rol. A mecha nical key is i nteg rated in
the master key¢
page 29.
@ Eme rgency key
The emergency key is not intended for constant
use . It shou ld only be used in an emergency, for
example, in place of the ign ition key
t:!:> page 72 . Ke ep it in a safe place and do not
car ry it on yo ur key r ing o r store it in the ve hicle.
Key replacement
If you lose a key, contact your author ized Audi
dealer immediately to have the
lost key disab led .
Be s ure to bring all your keys with you .
28
Number of keys
You can chec k the num ber of assigned keys to
your vehicle ¢
page 9. This allows you to make
sure yo u have received all of the keys when you
purchase a used vehicle .
Data in the master key
Dur ing driving, serv ice and maintenance-re levan t
da ta is cont inuous ly stored on your master key.
Your A udi service adviser can read out this data
and te ll yo u about the work your vehicle needs.
This applies also to veh icles with convenience
key *.
Personal comfort settings
If two people use one vehicle, it is recommended
that each person always uses "their own" maste r
k ey . W hen the ig nit ion is turned off or when the
vehicle is loc ked, personal conven ience settings
for the following systems are stored and as­
s igned to the remote master key.
- Climate control
- Power locking sy stem
- Sea t memory *
- Park ing system*
-Adapt ive cr uise control*
- Side assist*
- Drive se lect*
The stored settings are a utomat ica lly rec alled
when you unlock t he vehicle, when yo u ope n the
doo rs or when yo u turn on the ignition.
A WARNING
- Do not leave you r vehicle unattended with
the key in the ignition lock. Entry by una u­
thor ized persons could endanger you o r re­
sult i n theft o r damage the vehicle .
- Do not leave childre n unattended in the ve­
hicle, especially with access to vehicle keys .
Ungua rded access to the keys provides chil­
dren t he opport unity to start the engine
a nd /or ac tiva te ve hicl e sys tems s uch as the
power wi ndows etc. Unsu perv ised ope ration
of any vehicle system by children c an res ult
in ser ious injury.
.

a:,
a:,
...... N
" N ...... 0
0
LL co
Once the front passenger's door has been closed,
you cannot open it again from the outside. The
door can be opened from the inside by pulling
the door hand le.
A WARNING
Read and follow all WARNINGS¢&. in Gener­
al description on page 2
7 .
@ Tips
After the ignition is switched on, the power
locking system switch is enabled.
Electronic immobilizer
The immobilizer prevents your vehicle from being
started by unauthorized persons .
Inside the key there is a computer chip. This chip
automatically activates/deactivates the electron­ ic immobilizer.
Applies to vehicles with ignition lock:
The electronic immobilizer deact ivates automati­
cally when you insert the remote control key into
the ignition lock . It activates again automatically
when you remove the remote control key from
the ignition lock .
Applies to vehicles with convenience key:
If the remote control key is located inside the ve­
hicle and you press the
I START ENGINE STOPI
button , the electronic immobilizer deactivates
automatically. If you switch the ignition off and remove the remote control key from the vehicle,
the electronic immobilizer activates again auto­
matically .
A WARNING
Always take the key with you when you leave
the vehicle. The key can disarm the electronic
eng ine immobi lizer and permit an unauthor­
ized person to start the engine and enable op­
erat ion of the vehicle systems such as power
window or power sunroof leading to serious
personal injury.
Open ing and closing
(D Tips
-The vehicle cannot be started if an unau­
thorized key is used. The vehicle may not
start if another radio device such as a key
for another veh icle or a transponder is lo­
cated on the key ring.
- For Declaration of Compliance to United
States FCC and Industry Canada regulations
¢ page 249.
Luggage compartment
Lid
Opening /closing rear lid
Fig. 24 Rear lid: handle
Opening the rear lid
.. Press the button ~ on the remote control
master key for at least one second . The rear lid
unlocks and opens slightly. Or
.. Press the handle on the rear lid ¢
fig. 24.
Closing the rear lid
.. Pull the rear lid down at the gr ip on the inside
and allow it to drop gently to close it
Q &_.
A WARNING
-After closing the rear lid, always pull up on
it to make sure that it is properly closed.
Otherwise it could open suddenly when the
veh icle is moving.
- To help prevent po isonous exhaust gas from
being drawn into the vehicle, always keep
the rear lid closed while driving . Never
transport objects larger than those which fit
comp letely into the lu ggage area, because
then the rear lid cannot be fully closed. .,._
33

a:,
a:,
...... N
" N ...... 0
0
LL co
Power windows
Controls
The driver can control all power windows.
Fig. 27 Section of the driver's door: Controls
l
l
f
I
I !
I
Fig. 28 Center console : central power window switch
All power window switches ¢ fig. 2 7 are provided
with a
two-position function:
Opening the windows
"'Press the switch to the first stop and hold it un­
til the window reaches the desired position.
"' Press the switch briefly to the
second stop to
automatically open the window.
Closing the windows
"' Pull the switch to the first stop and hold it until
the window reaches the desired position.
"' Pull the switch briefly to the
second stop to au-
tomatically close the window.
Power window switches
@ Driver's door
@ Passenger 's door
© Left rear window
@ Right rear window
Opening and closing
You can open or close all the windows with the
switch ¢
fig. 28.
.&_ WARNING
-
-When you leave your vehicle -even if only
briefly - always remove the ignition key. This
applies particularly when children remain in
the vehicle. Otherwise the children could start the engine or operate electrical equip­
ment (e.g. power windows). The power win­
dows are functional until the driver's door or
passenger's door has been opened.
- Pay close attention when closing the win­
dows to prevent pinching of hands or limbs.
- When locking the vehicle from outside, the
vehicle must be unoccupied since the win­
dows can no longer be opened in an emer­
gency.
(D Tips
- When you open the doors, the windows au­
tomatically lower about 10 mm.
- After the ignition has been switched off, the
windows can still be opened or closed for
about 10 minutes. The window regulators
are not switched until the driver's or pas­
senger's door is opened.
Convenience opening/closing
The windows can be opened and closed with the
mechanical key or the emergency key.
Fig. 29 Key turns for opening and closing
Convenience opening feature
"'Use the emergency key or pull the mechanical
key o ut of the master key¢
page 29.
.,. Insert the key into the lock of the driver's door . ..,_
35