2017 AUDI A4 steering

Warm and cold
The temperatu re is maintained at a constant lev­
el when steering wheel heating is switched on.
The steering wheel heating settings are stored
automatically and assigned to the remote control
key that is in use.
72

(D Note
-Have your vehicle maintained properly and
in accordance with the service recommenda­
tions in your Warranty
& Maintenance book­
let. lack of proper maintenance as well as
improper use of the vehicle will impair the
function of the emission control system and
could lead to damage .
- Do not alter or
remove any component of
the Emission Control System unless ap­ proved by the manufacturer.
- Do not alter or
remove any device, such as
heat shields, switches, ignition wires,
valves, which are designed to protect your
vehicle's Emission Control System and other important vehicle components.
{t) Tips
The consumption estimates as published by
ENVIRONMENTAL PROTECTION AGENCY
(EPA) and Transport Canada may not corre­
spond to your actual consumption on the
road, which will vary depending upon vehicle
load and speed, road and weather conditions,
trip length, etc.
Steering
Adjusting the steering wheel position
The steering wheel position is adjustable up and
down and forward and back .
Fig. 76 Lever on the steeri ng col umn
.. Pull the lever in the direction of the arrow
¢,&. .
"'Bring the steering wheel into the desired posi­
tion.
Driving
.. Push the lever against the steering column un­
til it is secure.
A WARNING
Incorrect use of the steering wheel adjust­ ment and an incorrect seating position can
cause serious injuries.
-
- Only adjust the steering column when the
vehicle is stationary so that you do not lose
control of the vehicle.
- Adjust the driver's seat or steering wheel so
that there is at least a 10 in (25 cm) dis­
tance between your chest and the steering
wheel. If you do not maintain this distance
I
you will not be properly protected by the air­
bag system.
- If your physical characteristics prevent you
from sitting at least 10 in (25 cm) or more
away from the steering wheel, see if your
authorized Audi dealer or authorized Audi
Service Facility can provide adapters that
will help.
- If your face is level with the steering wheel,
the airbag does not provide as much protec­
tion during a collision. Always make sure that the steering wheel is level with your
chest.
- Always hold the steering wheel with your
hands in the 9 o'clock and 3 o'clock posi­
tions to reduce the risk of injury if the airbag
deploys.
- Never hold the steering wheel in the 12
o'clock position or with both hands on the
rim or the center of the steering wheel.
Holding the steering wheel incorrectly sig­
nificantly increases the risk of injury to the
hands, arms and head if the airbag deploys.
75

Driving
Starting and stopping
the engine
Starting the engine
The I S TAR T ENGIN E ST OP I button switches the
ignition on and starts the engine.
F ig . 77 Cockp it : S TAR T ENGI NE S TOP button
Starting the engine
.. Press the brake pedal¢.&, .
.. Press the
I S TAR T ENGINE STOPI button
c> fig . 77. The engine will star t .
.. It is possible that there will be a slight de lay
when starting the eng ine in d iesel veh icles in
colder temperatu res. Therefore, you must hold
the b rake peda l down until the eng ine starts.
T he
Iii in di cato r lig ht tu rns on while the en ­
gine is p reheat ing.
Sw itching the ignition on/off
If you would like to switch the ign ition on with­
ou t start ing the eng ine, fo llow these steps :
.. Press t he
I S TAR T ENGIN E STOPI button with ­
out
press ing the brake pedal. Ve hicles w ithout
the Start/Stop system* : the needle in the tach­
ometer moves into th e
READY position .
.. To swi tch the ign ition off, press t he b utton
ag ain. The needle in the ta ch ometer moves into
the
OFF pos it io n.
The prewarming r uns automatically in diese l
ve hicl es w hen the ig nitio n is swi tched on.
Equipment that uses a lot of electricity is switch ­
ed off temporarily when you sta rt the engine .
If the e ngine does not start immed iate ly, the
starting procedure stops automatically after a
short t ime . Repeat the starting procedure .
76
Start/Stop system*
Note the info rmation in ¢ page 78, Start/Stop
sys tem.
A WARNING
- To reduce the ris k of po ison ing, never allow
the engine to run in conf ined spaces .
- T he brake booster and power s teer ing no
longer f unction w hen you stop the engi ne.
You must use more force when braking or
steering . Because yo u cannot brake and
steer as you usually would, this cou ld lead
to accidents and serious injuries. These
fu nctions are st ill active if the Sta rt/Stop
system * has s topped the engine.
('Q) Note
Avo id h igh engine speed, full t hrottle, and
h eavy engine load if the eng ine has not
r eache d operat ing tempera tu re ye t. You could
d am age the eng ine.
@ For the sake of the environment
Do not let the eng ine run wh ile pa rked to
warm up . Beg in d riving immed iate ly . T his re­
du ces unne cess ary emissions .
(0 Tips
- Some noise afte r starting the eng ine is nor­
ma l and is no cause for co nce rn .
- If you leave the ve hicle w ith the ignition
switched on, the ign itio n w ill switch off af ­
te r a ce rtain amount of ti me. Make sure that
elect rical eq uip m ent such as the exterio r
ligh ts a re swi tched off .
Stopping the engine
.. Bri ng the vehicle to a full s top .
.. Press the
I S TAR T ENGINE ST OP I button
c> page 76, fig. 77 .
Emergency off function*
If i t is absolutely necessa ry, the eng ine ca n also
b e tu rned o ff whi le driving a t speeds starting at
4 mph ( 7 km/h) . To sw itch the engine o ff, press
the
I S T ART ENGI NE ST OPI button twice in a row .,.

<( a, .... N ,....
N .... 0 0
3 a,
briefly or press and hold for longer than two sec ­
onds.
A WARNING
- Never t urn off the engine before the veh icle
has come to a comp lete stop.
- Please note that the brake booster and pow­
er steering on ly work when the engine is
running. When the engine off, you must use
more force to steer or b rake the ve hicle. Be­
cause the usual steering and brak ing capa ­
b ili ty is not ava ila ble, the risk of accid ents o r
injuries i ncre ases .
- For safety reasons, always park the vehicle
with the se lector lever in the P position .
Ot herwise, the re is the r is k t hat the vehicle
c o ul d roll uninten tion ally.
- After the engine h as bee n sw itched off, the
r adi ator fan c an con tinue to run for up to
1 0
m inu tes -even wi th the ig nition switche d
o ff . I t can a lso switch on again after some
t ime if the coolant temperature rises as the
result of heat buildup or if t he engine is a l­
ready warm and the engine compartment is
also heated by the sun's rays.
(D Note
I f the en gine has been under heavy load for
an e xtended per io d of t ime, heat builds up in
the engine compartment after the engine is
sw itched off and there is a risk of damagi ng
the engine . For this reason, let the eng ine run
at idle fo r approximately two minu tes before
shut ting it off .
Messages
Engine running. Warning! Turn off ignition be­
fore leaving car
This message appea rs and a warn ing tone sounds
i f you open t he d river's doo r when the engi ne is
ru nning.
Please press brake pedal
This message appea rs if you do not press the
brake pedal when starting the eng ine.
D riving
Ill Remote control key: key not recognized. Is
the key still in the vehicle?
T h is ind icator l igh t tu rns on and this message ap­
pears if the ignition key was remove d from the
vehicle when the engi ne was running . If the ig ni­
tion key is no lo nger in the vehicle, you cannot
switch on the ignition or start the engine once
you stop it . You also cannot lock the ve hicle from
the outside .
Shift to P, otherwise vehicle can roll away.
Doors can be locked in P only
T h is mess age appears for safety re asons if the
selector lever is in the N pos it ion when yo u
switch the ignition off. Move the se lector lever to
t h e P position . Othe rw ise the vehicle is not pro­
tected from roll ing and it cannot be locked.
II Remote control key: hold back of key
against the de signated area. See owner' s man­
ual
If t he indica to r ligh t turns on and this message
appea rs, there is a malfunction ~
page 78.
Shift to P before leaving car, otherwise vehicle
can roll away
Th is message appears if the drive r's door is
opened wh ile the ign ition is switched on an d the
t ran sm issio n has not been s hifte d to t he
P posi­
t ion. Shift t he tr ansmission in to the
P p o sition
and t urn o ff the igni tion if you are leaving the ve­
hicle . Otherwise the vehicle could roll. A lso refe r
to
~ page 80.
77

Driving Starting the engine when there is a
malfunction
It may not be possible to start the engine under certain circumstances, for example if the battery
in the vehicle key is drained, if interference is af­
fected the key or if there is a system malfunc­
tion.
Fig. 78 Center console/remote contro l key: starting the
eng ine if there is a m alfunction
Requirement: the message Remote control key:
hold back of key against the designated area.
See owner's manual must display and the D)in­
dicator light must turn on.
.. Place the remote control key on the location
shown in the illustration
y>l) ~ fig. 78.
.. Press the brake pedal~ A in Starting the en­
gine on page
76.
.. Press the l~S_T_A_R_T_E_N_G_I_N_E_S_T_O_P_I button . The
engine will start .
.. Drive to an authorized Audi dealer or author­
ized Audi Service Facility immediately to have
the malfunction corrected.
(D Tips
You can view the message again by pressing the
I START ENGINE STOP! button.
Start/Stop system
Description
App lies to: ve hicles w ith S ta rt-Sto p system
The Start/Stop system can help increase fuel
economy and reduce CO2 emissions.
l ) Market -spe cific
78
In Start/Stop mode, the engine shuts off auto ­
matically when the vehicle is stopped, such as at
a traffic light. The ignition remains switched on
during this stop phase. The engine will restart automatically when needed.
The Start/Stop system is automatically activated as soon as the ignition is switched on.
Basic requirements for Start/Stop mode
-The driver's door must be closed.
- The driver 's seat belt much be fastened.
- The hood must be closed .
- The vehicle must have driven faster than
2 mph
(3 km/h) since the last time it stopped .
- A trailer must not be hitched to the vehicle .
If you leave the vehicle during a stop phase, the
engine can be restarted within approximately 30
seconds if the following requirements are met:
- The driver's door must be closed , the driver
must be wearing the safety belt and the brake
pedal must be pressed . Or:
- The driver's door must be closed, the brake
pedal must be pressed and a gear must be se­
lected.
({D Note
Always switch the Start/Stop system off when
driving through water
~page 78.
(D Tips
The engine stops shortly before the vehicle
comes to a stop
l). The full function of the
brake booster and the power steering is still
available.

Stopping and starting the engine
Applies to: vehicles with Start-Stop system
Fig. 79 Instrument cluster : eng ine sw itched off (s top
p hase)
~ B rake the ve hicle to a stop. The engine stops
shortly before the vehicle comes to a stop or if
the vehicle is stationa ry
1l. Keep your foot on
the brake pedal. The
II indicator light appears
in the stat us line at the bottom of the instru­
ment cluster d isplay. The needle in the tachom­
eter also moves into the READY
1l position .
~ The engine starts aga in when you take your
foot off the b rake pedal.
If the park ing brake is
set, the engine w ill only start aga in when the
a cce le rator pedal is p ressed
1>. The indica tor
li gh t turns off.
Additional information The engine stops i n the P, N and D selector lever
positions .
If you select the R pos ition dur ing a Stop phase ,
the eng ine will start again .
Select the P pos ition quickly to p revent the en­
g ine from starting unintentionally when sh ift ing
through R.
You can determine for yourself if the engine will
stop or not by reducing or increasing the amount
of force you use to press the brake pedal. For ex­
ample, if you only lig htly press on the brake ped­
al in stop-and-go traff ic or when turning, the en­
g ine will not switch off when the vehicle is sta­
tionary . As soon as you press the brake down
ha rder, the eng ine will switch off.
l l Ma rket -spe cific
Drivi ng
(D Tips
- Press the bra ke peda l during a Stop phase
to keep the vehicle from rolling.
- The ignition will turn off if yo u press the
!START ENGINE STOPI butto n dur ing a stop
phase. The needle in the tachometer moves
into the
OFF position.
General information
Applies to: vehicles with Start-Stop system
The standard Start/Stop mode con be canceled
for different system-related reasons.
F ig. 80 Instrument cluste r: eng ine stop temporarily un­
ava ilable
Engine does not switch off
Before and dur ing each stop phase, the system
checks if certain conditions have been met. For
example, the eng ine will not switch off in the fol­
lowing situations:
- The engine has not reached the minim um re­
quired temperature for Start/Stop mode.
- The inte rior temperature selected by the A/C
system has not been reached.
- The outside temperature is extremely high/low.
- The windsh ield is being defrosted .
- The battery charge level is too low .
- The steering wheel is turned at a sharp angle o r
is moving .
- After engaging the reverse gear .
- On sharp incl ines.
- At high altitudes .
r,jj also appears in the instrument cl uster d is­
play.
79

Automatic start /stop syst em: malfunct ion!
F unction una vailabl e. Please contact Ser vic e
There is a malfunction in the Start/Stop system .
Drive the vehicle to an authorized Audi dealer or
authori zed Service Facility as soon as possible to
have the malfunction corrected.
Electromechanical
parking brake
Operating
The electromechanical parking brake replaces
the hand brake.
Fig. 82 Center co nsole: parking brake
"'Pull the(®) ~ fig. 82 sw itch to set the park ing
brake . The LED in the switch illuminates . The
- (USA models)/ . (Canada models) a lso
turn on in the instrument cluster display
Q page 82, Starting from a stop .
"'To release the parking brake, press the brake or
accelerator pedal while the ignition is switched
on and press the button at the same time(®).
The LED in the button and the indicator light in
the display turn off.
Your vehicle is equipped with an electromechani­
cal parking brake . The parking brake is designed
to prevent the vehicle from rolling unintentional­
l y and replaces the hand brake .
In addition to the normal functions of a tradi­
tional hand brake, the electromechanical parking brake provides various convenience and safety
functions .
Emerg enc y braking function
The emergency braking fu nction ensures that the
vehicle can be slowed down even if the
standard
D rivi ng
brakes ma lfunction Q page 82, Emergency
braking function.
.&_ WARNING
-
- Do not press the acce lerator pedal inadver-
tently when the vehicle is stationary, the en­
gine is running and a gear is selected. Oth­
erwise, the vehicle will start to move imme­
diate ly and this could result in an accident .
- If the power supply fails, you cannot set the
parking brake if it is released . In this case,
park the veh icle on leve l ground and secure
it by p lac ing the selector leve r in the P posi­
tion. See an authorized A udi dealer or au ­
thorized A udi Se rvice Fa cil ity for assis tance.
(D Tips
- Occasional noises when the parking brake is
set and released are normal and are not a
cause fo r concern.
- The pa rking brake goes through a self-test
cy cle at regu lar inte rvals when the vehicle is
stopped . Any no ises asso ciated wi th th is are
normal.
- If there is a powe r failure, the parki ng brake
canno t be set if it is rele ased, and i t will not
re lease if it is set ~& . See an a uthorized
Audi dealer or authorized Audi Service Fa­
cility for assistance.
- If the parking brake is malfunctioning, the
LED in the
C® button blinks . It may not be
possible to set the parking brake . If the
park ing brake is set, use the hill start assist
to release it
Q page 82
Parking
.,. Press the brake pedal to stop the veh icle.
.,. Pull the
C® switch to set the parking b rake .
.,. Select the P se lector lever position .
.,. Switch the engine off
Q _&. .
.,. Turn the steering w heel when par king o n in­
clines so that the wheels w ill roll into the cu rb
if the vehicle starts moving .
81

<( a, .... N ,....
N .... 0 0
3 a,
-tiptronic does not work if the transmission
is running in emergency mode.
Kick-down
Kick-down enables maximum acceleration.
When you press the accelerator pedal down be­
yond the resistance point, the automatic trans­
mission shifts down into a lower gear and the en­
gine utilizes its full power, depending on vehicle
speed and engine RPM. It shifts up into the next
higher gear once the maximum specified engine
RPM is reached .
A WARNING
Please note that the wheels could spin on
slick or slippery roads when kick-down is ac­
tive.
Launch control program
The launch control program provides the best
possible acceleration when starting from a stop.
Requirement: The engine must be at operating
temperature and the steering wheel must not be
turned .
~ Deactivate the Start/Stop system* ¢ page 80.
The LED in the 10 ml button turns on.
~ With the engine running, press the ~l.i; -o~FF =! but­
ton briefly ¢
page 135. The II indicator light
turns on and the message
Stabilization control
(ESC): Sport. Warning! Restricted stability
ap­
pears in the instrument cluster display.
~ Pull the selector lever back out of the D/S posi­
tion briefly to select the S position or select the
Dynamic driving mode in drive select*
¢page 122.
~ Press the brake pedal firmly with your left food
and hold it all the way down for at least 1 sec­
ond.
~ At the same time, press the gas pedal all the
way down with your right foot until the engine
reaches and stays at a high RPM level.
~ Remove your foot from the brake pedal within
S seconds ¢
,&..
Driving
A WARNING
-Always adapt your driving to the traffic flow.
- Only use the Launch control program when
road and traffic conditions allow it and oth­
er drivers will not be endangered or both­
ered by your driving and the vehicle's accel­
eration.
- Please note that the drive wheels can spin
and the vehicle can break away when sport
mode is switched on, especially when the
road is slippery.
- Once the vehicle has started moving, press
the
1 .$ OFFI button briefly to turn the sport
mode off.
(D Tips
- The transmission temperature may increase
significantly after using the launch control
program. If that happens, the program may
not be available for a few minutes. It will be
available again after a cool-down period.
- When accelerating using the launch control
program, all vehicle parts are subject to
heavy loads. This can lead to increased
wear.
Transmission malfunction
• Transmission: too hot. Please stop vehicle
Do not continue driving . Select the P selector lev­
er position and contact an authorized Audi dealer
or authorized Audi Service Facility for assistance.
• Transmission: malfunction! Please stop ve­
hicle and shift to P
Do not continue driving . Select the P selector lev­
er position and contact an authorized Audi dealer
or authorized Audi Service Facility for assistance.
@] Selector lever: malfunction! You may contin­
ue driving. Please contact Service
There is a system malfunction in the transmis­
sion. Drive to an authorized Audi dealer or au­
thorized Audi Service Facility immediately to have
the malfunction corrected .
[O] P button: malfunction! Auto P when engine
off. Please contact Service ..,.
87