2017 AUDI A4 coolant

reproductive harm. In addition, certain flu­
ids contained in vehicles and certain prod­
ucts of component wear contain or emit
chemicals known to the State of California
to cause cancer and birth defects or other
reproduct ive harm.
- Battery posts, terminals and related acces­
sories contain lead and lead compounds,
chem icals known to the State of California
to cause cance r and rep roductive harms.
Wash hands after handling.
(D Note
When filling flu ids, be sure not to mix the flu­
ids up . Otherwise severe ma lfunctions and en­
gine damage w ill occur.
@ For the sake of the environment
You should regularly check the grou nd under
your veh icle in order to detect Leaks qu ickly . If
there are v isible spots from oil or other fluids,
bring your vehicle to an authorized Aud i dea l­
er or authorized Audi Service Facility to be
checked.
Opening the hood
The hood is released from the interior.
F ig. 2 45 Dri ver fo otw ell : rele ase leve r
Checki ng an d Fill in g
Fig. 246 Unlocke d hood: lever
Make sure the wiper arms are not raised up from
the windshield. Otherwise the paint could be
damaged .
.,. With the driver's door open, pull the lever be­
low the instrument pane l in the direction of the
arrow
c;> fig. 245 .
.,. Raise the hood slightly c;> ,&. .
.,. Press the lever c;> fig. 246 in the direct ion of the
arrow. This releases the hooks .
.. Open the hood .
A WARNING
-
Never open the hood if you can see steam or
coolant escaping from the engine compart­ ment, because this increases the risk of
burns. Wait until no steam or coolant is es­
cap ing .
Closing the hood
.,. Push the hood down until you override the
force of the str uts .
.,. Let the hood fall lightly into the latch .
Do not
press it in.
c;> &_ .
A WARNING
-===
If the hood is not latched complete ly, it could
fly up wh ile you are driving and obstruct your
vis ion.
- For safety reasons, the hood must always be
closed securely while driv ing. Because of
this, always check the hood after closing it
to make sure it is latched correctly . The
hood is latched if the front corners cannot
be lifted.
~
305

Checking and Filling
-If you notice that the hood is not latched
wh ile you are dr iv ing, stop immediately and
Engine compartment overview
The most important check points .
close it, because driving when the hood is
not latched increases the r isk of an accident.
F ig. 247 Ty pical lo ca tion of th e reservoir a nd the engine o il filler op ening
@ Washer fluid reservoir (0) . . . . . . 316
@ Jump start po int( +) under a cover,
(-) with hex head screw . ...... .. 314,356
@ Eng ine oil filling opening
( @ Coolant expansion tank (-L) . . . . . 310
® Brake fluid reservoir (0)) . . . . . . . 31 1
The location of the engine oil filling hole and the coo lant expansion tank~
fig. 247 (items @and
@) may differ depending on the engine version .
A WARNING
Read and follow all WARNINGS before check­
ing anything in the eng ine compartment
~ page 304.
306
Engine oil
Engine oil specifications
The engine oil used must conform to exact speci­
fications .
The serv ice interval d isplay in the instrument
cluster of your vehicle will inform you when it is
time for an o il change. We recommend that you
have you r oil changed by an author ized Audi Se rv­
i ce Adv isor.
If you have to top off the oil between oil changes, u se the Audi oil quality standard specif ied in the
tab~.
~

Checking and Filling
Cooling system
Coolant
The engine coo ling system is filled with a mixture
of pur ified water and coolan t addit ive at the fa c­
tory. This coo lant must not be not changed.
The coolant leve l is monito red throug h the . in­
dicator light~
page 31. Howeve r, we do recom­
mend occasionally check ing the coo lan t level
manually.
I f you must add coolant, use a m ixture of water
and coolant additive. M ixing the coolant additive
with d istilled wate r is recommended.
Coolant additive
The coolant additive is made of anti-freezing a nd
corros ion protection agents. Only use the fo llow­
ing coo lant add it ives. These additives may be
m ixed w ith each other.
Coolant additive Specification
G13
TL 774)
G12++ TL 774 G
The amount of coo lant add itive that needs to be
mixed w it h water depends on the climate where
the vehicle will be operated. If the coolant addi­
tive percentage is too low, the coolant can freeze
and damage the engine.
Coolant Freeze protec-
additive tion
Warm min. 40% m in. -13 °F
reg ions max. 45% (-25 °C)
Cold min. 50% max. -40 °F
reg ions max. 55% (-40 °C)
(D Note
- Befo re the start of winter, have your author­
i zed Audi dealer or authorized A udi Service
Fac ility check if the coolant additive in yo ur
vehicle matc hes the percentage approp riate
fo r the climate. Th is is especially important
when driving in co lde r climates.
- If the appropriate coolant additive is not
available in an emergency, do not add any
other additive. You cou ld damage the en-
310
gine . If this happens, only use water and re ­
store the correct m ixt ure ratio with the
specified coo lant add itive as soon as poss i­
ble.
- On ly ref ill with new coolant .
- Rad iator sealant mus t not be mixed wi th
the coolant.
Adding coolant
Fig. 24 9 Eng ine co mpart m ent: re lease button on coolant
expansio n tank
Check ing the engine coolant level
.,. Park your veh icle on a level surface.
.,. Switch the ignit ion off.
.,. Read the coolant level on the coolant expansion
tank
c:> fig . 249 .
.,. The coolant leve l mus t be between the MIN and
MAX mar kings when the engine in co ld. Whe n
t he engi ne is warm i t ca n be sligh tly above the
MAX mar kin g.
Adding coolant
.,. Let the engi ne cool down.
.,. Place a cloth over the coo lant expansion tank
cap.
.,. Push the rele ase button¢
fig. 249 and carefu l­
ly unsc rew the cap to the left un til you feel re­
sis tance ¢,&. .
.,. Push the release button again and remove the
cap completely.
.,. Make sure that the fluid level remains stab le.
Add more coolant if necessary .
.,. Turn the cap to the right to secure it until you
feel res istance a second time.
Coolant loss usually ind icates there is a leak. Im­
med iate ly dr ive your vehicle to an author ized
Audi dealer or authorized A udi Service Fac ility ..,.

and have the cooling system inspected. If the
cooling system is not leaking, a loss can come
from the coolant boiling through overheating and being pushed out of the cooling system.
A WARNING
- The cooling system is under pressure. Do
not open the coolant expansion tank cap
when the engine is hot. This increases the
risk of burns .
- The coolant add itive and the coolant can be
dangerous to your health. For this reason,
keep the coolant in the original container
and away from children. There is a risk of
poisoning.
- When working in the engine compartment,
remember that the radiator fan can switch
on even if the ignition is switched off, which
increases the risk of injury.
(D Note
Do not add coolant if the expansion tank is
empty. There may be a ir in the cooling sys­
tem, which increases the risk of engine dam­
age . If this is the case, do not continue driv­
ing . See an authorized Audi dealer or author­
ized Audi Service Facility for assistance.
Brake fluid
Checking brake fluid level
The brake fluid level can be checked with a quick
glance .
Fig. 250 Engine compa rtment: Cover o n the brake fluid
rese rvoir
Before you check anything in the eng ine compart ­
ment,
always read and heed all WARNINGS
Checking and Filling
c::> .&. in Working in the engine compartment on
page 304.
" Read the brake fluid level from the brake fluid
reservoir
c::> fig. 250, c::> page 306, fig. 247. The
brake fluid level must be between the "MIN"
and "MAX" markings.
The brake flu id reservoir is located at the rear
partition of the engine compartment on the left
side
~ page 306 .
The fluid level may drop slightly after some time
due to the automatic adjustment of the brake
pads . This is not cause for alarm.
If the brake fluid level falls considerably below
the "MIN" mark, the brake warning/indicato r
light (USA models:
11111 , Canada models : II>
will come on c::> page 29. Do not continue to oper­
ate the vehicle. The complete brake system
should be thoroughly checked by an authorized
Audi dealer or qualified workshop and the cause
corrected . If the brake fluid level is too low, the
brake warning/indicator light will illuminate .
Contact an authorized Audi dealer
immediately .
@ Tips
The brake fluid reservoir is located under­
neath the cover.
Changing brake fluid
Hove the broke fluid changed by on experienced
technician.
Brake fluid absorbs moisture from the air. If the
water content in the brake fluid is too high, cor­
rosion in the brake system may result after ape­
riod of time. The boiling point of the brake fluid
will also decrease considerably and decrease braking performance .
Therefore, the brake fluid must be changed
every
two years .
Always use new brake fluid which con­
forms to Federal Motor Vehicle Standard "FMVSS
116 DOT 4" .
The brake fluid reservoir can be difficult to reach,
therefore, we recommend that you have the brake fluid changed by your authorized
Audi
dealer.
Your dealer has the correct tools, the
311

Wheel s
Bead separation
means a breakdown of the bond
between components in the bead .
Cord
means the strands forming the
plies in the tire.
Cold tire inflation pressure
means the tire pressure recom­
mended by the vehicle manufac­
turer for a tire of a designated
size that has not been driven for more than a couple of miles (kilo­
meters) at low speeds in the
three hour period before the tire
pressure is measured or adjusted.
Curb weight
means the weight of a motor ve­
hicle with standard equipment in­
cluding the maximum capacity of
fuel, oil, and coolant, air condi­
tioning and additional weight of
optional equipment.
E x tra load tire
means a tire designed to operate
at higher loads and at higher in­
flation pressures than the corre­ sponding standard tire . Extra load
tires may be identified as "XL",
"xl", "EXTRA LOAD", or "RF" on
the sidewal l.
320
Gross Axle Weight Rating
("GAWR ")
means the load-carrying capacity
of a single axle system, measured
at the tire -ground interfaces .
Gross Vehicle Weight Rating
(" GVWR ")
means the maximum total loaded
weight of the vehicle .
Groove
means the space between two ad­
jacent tread ribs .
Load rating (code )
means the maximum load that a
tire is rated to carry for a given in ­
flation pressure. You may not find
this information on all tires be­
cause it is not required by law.
Ma ximum load rating
means the load rating for a tire at
the maximum permissible infla­ tion pressure for that tire.
Ma ximum loaded vehicle
weight
means the sum of :
(a) Curb weight
(b) Accessory weight
(c) Vehicle capacity weight, and
(d) Production options we ight

<( a, .... N ,....
N .... 0 0
3 a,
Wheels
Model/ Tire designation Tire pressure
Engine Normal load Maximum load
(up to 3 people)
front rear front rear
PSI
225/50 Rl 7 94H
30 All Season
A4: 245/40 R18 93Y
2.0L High Performance
30
4 cylinders
245/40 R18 97H
Gasoline
35
engine All Season
245/35 R19 93Y
36 High Performance
225/50 Rl 7 94H
32 All Season
A4: 245/40 R18 93Y
2.0L High Performance
30
4 cylinders
245/40 R18 97H
Diesel en-
35
gine All Season
245/35 R19 93Y
35 High Performance
A WARNING
Please note the important safe­
ty precautions regarding tire pressure
¢ page 32 7 and load
limits
¢ page 329.
Tires and vehicle load limits
There are limits to the amount of
load or weight that any vehicle
and any tire can carry. A vehicle
that is overloaded will not handle
well and is more difficult to stop. Overloading can not only lead to
loss of vehicle control, but can al­
so damage important parts of the
vehicle and can lead to sudden
kPA PSI kPA PSI kPA PSI kPA
210 28 190 35
240
35 240
210 28 190 33 230 33 230
240 32 220 36 250 36 250
250 33 230 41
280
44 300
220 29 200 36 250 36 250
210 28 190
33 230
33 230
240 32 220 36 250 36 250
240 32 220 39 270 42 290
tire failure, including a blowout
and sudden deflation that can
cause the vehicle to crash.
Your safety and that of your pas­
sengers also depends on making
sure that load limits are not ex­
ceeded. Vehicle load includes ev­
erybody and everything in and on
the vehicle. These load limits are
technically referred to as the vehi­ cle's
Gross Vehicle Weight Rat­
ing
("GVWR").
The "GVWR" includes the weight of the basic vehicle, all factory in­
stalled accessories, a full tank of
fuel, oil, coolant and other fluids ..
329

Technical data
Vehicle specifications
F ig. 281 W indshield (front left): Ve hicle Ident ification
Number (VIN)
XXXXX XX -X -XX XX X XX XX
CD+ ~t :1 :: xxxxxxxx xx x xxx xxxxx
TVP/fffl XXX XXX
XX XXXXXXX XX X X XX
XXX
KW XXX
®i ~:J ·f lfils~~ XXXX XXX XXX
®-+ ~N:a=i~l xxxx ; xxxx xx x ; xx
11. • AUSS, I OPTIONS
E0 A
7D 5 4UB 6
XM 5SG 5R W
2E H
J0Z lL B l
A S lB A
3FC SM U 7 Xl
F 0 A 9G3 0G7 0YH 0JF
TL 6 3KA 8EH UlA X 98 Q Z7
lXW 803 908 824 020
7T6 C V7 7 K0 4 X3 2K2
3L4
4KC 3 Y 0 413
502
lSA 7GB 01 A 4G0
XX . X XX X XX X xxxx
Fig. 282 Vehicle identification label
Vehicle Identification Number (VIN) in the
Infotainment system
• Select in the Infotainment system: the I MENU I
button > left control button > Service & checks
> Vehicle information.
Vehicle Identification Number (VIN)
The VIN can be found in the Infotainment sys­
tem, on the vehicle data label and under the
windshield on the driver's side*¢
fig. 281 . The
VIN is also in the right side of the luggage com­
partment.
Technical data
Vehicle identification label
T he veh icle identification label¢ fig. 282 is locat­
ed in the luggage compartment under the cargo
floor cover .
T he information of the veh icle identification label
can also be found in your Warranty
& Mainte­
nance booklet.
The sticker contains the fol low ing vehicle data:
(D Vehicle Identification Number (VIN)
@ Vehicle type, eng ine output, transm ission
@ Engine and transmission codes
@ Paint and interior codes
® Optional equipment numbers
Safety compliance sticker
The safety compliance sticker is your assurance
that your new vehicle complies w ith all applicable
Federal Motor Vehicle Safety Standards which
were in effect at the time the vehicle was manu­
factured. You can find this sticker on the front end of the driver's door.
It shows the month and
year of production and the vehicle identification number of your vehicle (perforation) as well as
the Gross Vehicle Weight Rating (GVWR) and the Gross Axle Weight Rating (GAWR).
High voltage warning label
The high voltage warning label is located in the
engine compartment next to the engine hood re­
lease. The spark ignition system complies with
the Canadian standard ICES-002.
Weights
Gross Vehicle Weight Rating
The Gross Vehicle Weight Rating (GVWR), and
the Gross Axle Weight Rating (GAWR) for front
and rear are listed on a sticker on the front end of
the driver's door .
The Gross Vehicle Weight Rating includes the
weight of the basic vehicle plus full fuel tank, oil and coolant, plus maximum load, which includes
passenger weight (150 lbs/68 kg per designated
seating pos ition) and luggage weight¢,&. . .,.
361

Consumer inf orm ation
today's a utomo biles, have steadily re duced the
scope of maintenance and repairs whic h can be
carried out by veh icle owners.
Also , sa fet y and
en vironmental
concerns place very strict limits
on the nature of repairs and adjustments to en­
g ine and transmission parts wh ich an owner can
perform .
Maintenance, adjustments and repairs usually re­
qu ire special tools, testing devices and other
equ ipment available to specially trained work ­
shop personnel in order to assure proper per­
forma nce, re liability and safety of the veh icle and
its many systems.
Improper maintenance, adjustments and repairs
can impair the operation and reliab ility of your
ve hicle and eve n void your vehicle warranty .
Therefo re, proof of se rvicing in a ccordance w ith
the m aintenance sched ule may be a condition for
up ho ld ing a possible wa rranty claim made within
the wa rranty pe riod.
Above all, ope rational safety can be adversely af­
fected, cre ating unne cessa ry risks fo r you and
your passengers.
I f in doubt about any servicing, have it done by
your author ized Audi dealer or any other properly
eq uipped and qualified workshop . We strongly
urge you to g ive your author ized Audi dealer the
opportunity to perform a ll scheduled mainte ­
nance and necessa ry repairs. Your dealer has the
facilities, origina l parts and tra ined specialists to
keep your veh icle runn ing properly.
P e rforming limited maintenance yourself
The fo llow ing pages describe a limited number of
procedures whic h can be performed on your vehi­
cle with ordinary tools, should the need arise and
tra ined personnel be unava ilable. Before per­
forming any of these procedures, always thor­
ough ly read all of the app licab le text and carefu l­
ly follow the instructions g iven . A lways rigorously
observe the
WARNINGS prov ided .
Befo re yo u check anything in the engine com ­
partment, always read and heed all WARNINGS
c::> & and c::> & in Working in the engine compart­
ment on page 304.
364
A WARNING
-
- Ser ious personal in jury may occur as a result
of imp roperly performed maintenance, ad­
justments or repairs .
- Always be extreme ly careful when work ing
on the vehicle . Always follow commonly ac­
cepted safety practices and general com­ mon sense. Never r is k personal in jury.
- Do not attempt any of the mainte nance,
checks or repairs described on the following pages if you are no t fu lly fam iliar with these
or other proce dures with respect to the ve­
hicle, o r are uncert ain how to p ro ceed.
- Do not do any work wi thout the prope r tools
a nd equi pmen t. H ave the necess ary wo rk
done by your authorized Au di dealer or an ­
other properly equipped and qualified work­
shop.
- The engine compartment of any motor vehi ­
cle is a potentially hazardous area . Never
reach into the a rea around or touch the radi­
ator fan. It is temperature controlled and
can switch on suddenly - even when the en­
gine is off and the ignition key has been re­
moved. The rad iator fan switches on auto­
mat ica lly when the coolant reaches a certain
temperature and will con tinue to ru n until
the coolant temperat ure drops.
- Always remove the igni tion key before any­
one gets u nder the vehicle.
- Always support your vehicle with safety
stands if it is necessary to work underneath
the vehicle. The ja ck* s upplied w ith the vehi­
cle is no t ad equate for t his purpose and
could collapse causing se rious personal in ­
jury .
- If you must wor k underne ath the vehicle
with the wheels on t he ground, always make
sure the vehicle is on level ground, that the
wheels a re always sec urely blocked and that
the engine cannot be started.
- Always make sure the transmission se lector
lever (automatic t ransm iss ion) is in P (Park
position) and the park b rake is applied.