2016 YAMAHA XENTER 150 clock

Instrument and control functions
3-3
1
23
4
5
6
7
8
9
10
11
12
6-34 for further instructions.
EAUT1936
Engine trouble warning light “ ”
This warning light flashes or stays on if
an electrical circuit monitoring the en-
gine is not working correctly. If this oc-
curs, have a Yamaha dealer check the
self-diagnosis system.
The electrical circuit of the warning light
can be checked by turning the key to
“ON”. The warning light should come
on for a few seconds, and then go off.
If the warning light does not come on
initially when the key is turned to “ON”,
or if the warning light remains on, have
a Yamaha dealer check the electrical
circuit.
EAUT3725
Multi-function display
WARNING
EWA12313
Be sure to stop the vehicle before
making any setting changes to the
multi-function display. Changing
settings while riding can distract the
operator and increase the risk of anaccident.
The multi-function display is equipped
with the following:

an odometer

a fuel reserve tripmeter (which
shows the distance traveled since
the bottom segment of the fuel me-
ter and fuel level warning indicator
1. V-belt replacement indicator “V-BELT”
2. Clock
3. Oil change indicator “OIL CHANGE”
4. “SELECT” button
5. Fuel level warning indicator “ ”
6. Fuel meter
7. Speedometer
8. Odometer
9. “RESET” button
10.Tripmeter 1
11.Ambient temperature display
12.Tripmeter 2
SELECT
RESET
ODOOIL
TRI P 1 BE LT TRI P
2
OIL CHANGECLOOK
OUT TEM P
12
34
5 6
78 9
10 12
11
U52SE1E0 3 ページ ２０１５年９月１６日　水曜日　午後５時２７分

Instrument and control functions
3-4
1
234
5
6
7
8
9
10
11
12
started flashing)

two tripmeters (which show the
distance traveled since they were
last set to zero)

an oil change tripmeter (which
shows the distance traveled since
the last engine oil change)

an oil change indicator (which dis-
plays when the engine oil should
be changed)

a V-belt replacement tripmeter
(which shows the distance trav-
eled since the V-belt was last re-
placed)

a V-belt replacement indicator

an ambient temperature display

a clock

a fuel meter

a brightness control mode
TIP
When the key is turned to “ON”, all
segments of the display come on
for a few seconds. During this
time, the multi-function display is
performing a self-test.

Be sure to turn the key to “ON” be-
fore using the “SELECT” and “RE-
SET” buttons except when setting
the brightness mode.
Odometer, fuel tripmeter, tripme-
ters, oil change tripmeter and V-belt
tripmeter modes
Pushing the “SELECT” button switches
the display among the odometer mode
“ODO”, the fuel tripmeter mode “F”, the
tripmeter modes “TRIP 1” and “TRIP 2”,
the oil change tripmeter mode “OIL
TRIP” and the V-belt change mode
“BELT TRIP” in the following order:
ODO  F  TRIP 1  TRIP 2  OIL
TRIP  BELT TRIP  ODO
When approximately 1.6 L (0.42 US
gal, 0.35 Imp.gal) of fuel remains in the
fuel tank, the bottom segment of the
fuel meter and fuel level warning indica-
tor will start flashing, and the display will
automatically change to the fuel re-
serve tripmeter mode " F" and start
counting the distance traveled from that
point. In that case, pushing the "RE-
SET" button switches the display to the
previous mode.
To reset a tripmeter, select it by push-
ing the “SELECT” button until “Trip” or
“Trip F” begins flashing (“Trip” or “Trip F” will only flash for five seconds).
While “Trip” or “Trip F” is flashing, push
the “RESET” button for at least one
second. If you do not reset the fuel re-
serve tripmeter manually, it will reset it-
self automatically and the display will
return to the prior mode after refueling
and traveling 5 km (3 mi).
TIPThe display cannot be changed back to
fuel reserve tripmeter “F” after pushingthe “RESET” button.
OdometerTIP
For the U.K.: For any mode, the
odometer units can be switched
from kilometers to miles by push-
ing the “SELECT” button for 1 sec-
ond.

If the odometer indicates “-----”,
have a Yamaha dealer check the
multi-function display, as it may befaulty.
Tripmeters
To reset a tripmeter, select it by push-
U52SE1E0 4 ページ ２０１５年９月１６日　水曜日　午後５時２７分

Instrument and control functions
3-6
1
234
5
6
7
8
9
10
11
12
TIP
If the ambient temperature falls be-
low –10 C, a lower temperature
than –10 C will not be displayed.

If the ambient temperature climbs
above 40  C, a higher temperature
than 40 C will not be displayed.

The accuracy of the temperature
reading may be affected when rid-
ing slowly (approximately under 20
km/h (12 mi/h)) or when stopped at
traffic signals, railroad crossings,etc.
Clock
To set the clock:
1. Push the “SELECT” button and “RESET” button together for at
least two seconds.
2. When the hour digits start flashing, push the “RESET” button to set the
hours.
3. Push the “SELECT” button, and the minute digits will start flashing.
4. Push the “RESET” button to set the minute digits.
5. Push the “SELECT” button and then release it to start the clock.
Fuel meter
The fuel meter indicates the amount of
fuel in the fuel tank. The display seg-
ments of the fuel meter disappear to-
wards “E” (Empty) as the fuel level
decreases. When the bottom segment
of the fuel meter and fuel level warning
indicator “*” starts flashing, refuel as
soon as possible. When the key is
turned to “ON”, all of the display seg-
ments of the fuel meter will appear for a
few seconds, and then shows the actu-
al fuel level.
Brightness control mode
This function allows you to adjust the
brightness of the speedometer panel to
suit the outside lighting conditions.
To set the brightness
1. Turn the key to “OFF”.
2. Push and hold the “SELECT” but- ton.
3. Turn the key to “ON”, and then re- lease the “SELECT” button after
five seconds. The display will
change to brightness control mode.
4. Push the “RESET” button to select the desired brightness level in the
following order: BL-01  BL-02 
BL-03  BL-04  BL-05 
BL-01.
5. Turn the key to “OFF”.
U52SE1E0 6 ページ ２０１５年９月１６日　水曜日　午後５時２７分

Instrument and control functions
3-8
1
234
5
6
7
8
9
10
11
12
EAUS1963
Rear brake leverThe rear brake lever is located on the
left handlebar grip. To apply the rear
brake, pull the lever toward the handle-
bar grip.
This model is equipped with a unified
brake system.
When pulling the rear brake lever, the
rear brake and a portion of the front
brake are applied. For full braking per-
formance, apply both brake levers si-
multaneously.TIP
As the unified brake system is me-
chanical, additional free play can
be felt in the front brake lever when the rear brake lever is being
pulled.

The unified brake system does not
function when the front brake isapplied alone.
EAUT3591
Fuel tank capTo remove the fuel tank cap
1. Open the seat. (See page 3-11.)
2. Turn the fuel tank cap counter- clockwise and pull it off.
To install the fuel tank cap 1. Insert the fuel tank cap into the tank opening and turn it clockwise
until the “ ” marks on the cap and
rubber mat are aligned.
2. Close the seat.
WARNING
EWA11092
Make sure that the fuel tank cap is
1. Rear brake lever
1
1. Fuel tank cap
2. Match marks
1
2
U52SE1E0 8 ページ ２０１５年９月１６日　水曜日　午後５時２７分

Instrument and control functions
3-11
1
23
4
5
6
7
8
9
10
11
12
EAU13933
SeatTo open the seat 1. Place the scooter on the center- stand.
2. Insert the key into the main switch, and then turn it counterclockwise
to “OPEN”.TIPDo not push inward when turning thekey.
3. Fold the seat up.
To close the seat 1. Fold the seat down, and then push it down to lock it in place. 2. Remove the key from the main
switch if the scooter will be left un-
attended.
TIPMake sure that the seat is properly se-cured before riding.
EAUT3711
Passenger footrestTo use the passenger footrest, pull it
out as shown.
To retract the passenger footrest, push
it back to original position.
1. Turn.
1
1. Passenger footrest
1
U52SE1E0 11 ページ ２０１５年９月１６日　水曜日　午後５時２７分

Periodic maintenance and adjustment
6-29
1
2
3
4
56
7
8
9
10
11
12 2. Remove the bulb cover, and then
disconnect the headlight coupler.
3. Unhook the headlight bulb holder, and then remove the burnt-out
bulb. 4. Place a new headlight bulb into po-
sition, and then secure it with the
bulb holder.
5. Connect the coupler, and then in- stall the headlight bulb cover.
6. Install the cowling together with the headlight unit.
7. Have a Yamaha dealer adjust the headlight beam if necessary.
EAUT3641
Replacing an auxiliary light
bulbIf an auxiliary light bulb burns out, re-
place it as follows.1. Remove cowling A. (See page 6-8.)
2. Remove the socket (together with the bulb) by turning it counter-
clockwise.
3. Remove the burnt out bulb by pull- ing it out.
1. Headlight bulb cover
1. Headlight coupler
2. Headlight bulb holder
3. Headlight bulb
1
1
2
3
1. Auxiliary light bulb socket
1
U52SE1E0 29 ページ ２０１５年９月１６日　水曜日　午後５時２７分

Periodic maintenance and adjustment6-30
1
2
3
4
567
8
9
10
11
12
4. Insert a new bulb into the socket.
5. Install the socket (together with the
bulb) by turning it clockwise.
6. Install the cowling.
EAU24182
Tail/brake lightThis model is equipped with an
LED-type tail/brake light.
If the tail/brake light does not come on,
have a Yamaha dealer check it.
EAUT3652
Replacing a front turn signal
light bulbIf a front turn signal light burns out, re-
place it as follows. 1. Remove cowling A. (See page 6-8.)
2. Remove the socket (together with the bulb) by turning it counter-
clockwise.
3. Remove the burnt out bulb by pushing it in and turning it counter-
clockwise.
1. Auxiliary light bulb
1
1. Turn signal light bulb socket
1
U52SE1E0 30 ページ ２０１５年９月１６日　水曜日　午後５時２７分

Periodic maintenance and adjustment
6-31
1
2
3
4
56
7
8
9
10
11
12 4. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
NOTICE
ECAU0081
If a turn signal light bulb of different
wattage than recommended is used,
the turn signal light flashing may beaffected.
5. Install the socket (together with the bulb) by turning it clockwise.
6. Install the cowling.
EAUT3671
Replacing a rear turn signal
light bulb1. Remove the turn signal lens by re- moving the screw.
2. Remove the burnt-out bulb by pushing it in and turning it counter-
clockwise.
3. Insert a new bulb into the socket, push it in, and then turn it clock-
wise until it stops.NOTICE
ECAU0081
If a turn signal light bulb of different
wattage than recommended is used,
the turn signal light flashing may beaffected. 4. Install the lens by installing the
screw. NOTICE: Do not over-
tighten the screw, otherwise the
lens may break.
[ECA11192]
1. Turn signal light bulb
1
1. Turn signal light bulb
1
U52SE1E0 31 ページ ２０１５年９月１６日　水曜日　午後５時２７分