2016 TOYOTA VENZA reset

73 1
1-3. Adjustable components (seats, mirrors, steering wheel)
Before driving
VENZA_OM_OM73030U_(U) Driving position memor y 
 : If equippedYour preferred driving position (the position of the driver’s seat and
angle of the outside rear view mirrors) can be memorized and
recalled by pressing a button. It is also possible to set this function
to activate automatically wh en the doors are unlocked.
Two different driving positions can be entered into memory.
■ Entering a position to memory
Check that the shift lever is in P.
Vehicles with smart key system: Turn the “ENGINE START
STOP” switch is in IGNITION ON mode.
Vehicles without smart key system: Turn the engine switch
is in the “ON” position.
Adjust the driver’s seat and outside rear view mirrors to the
desired positions.
While pressing the “SET” but-
ton, or within 3 seconds after
the “SET” button is pressed,
press button “1” or “2” until the
signal beeps. If the selected button has
already been preset, the previ-
ously recorded position will be
overwritten.STEP 1
STEP 2
STEP 3
STEP 4

1892-2. Instrument cluster
2
When driving
VENZA_OM_OM73030U_(U) Instrument panel light control
The brightness of the instrument panel lights can be adjusted.
Darker
BrighterOdometer/trip meter and trip meter reset button Switches between odometer and trip meter displays. Pushing and hold-
ing the button will reset the trip meter when the trip meter is being dis-
played.
Odometer and trip meter Odometer: Displays the total distance the vehicle has been driven.
Trip meter: Displays the distance the vehicle has been driven since the
meter was last reset. Trip meters A and B can be used to record and
display different distances independently.

1952-2. Instrument cluster
2
When driving
VENZA_OM_OM73030U_(U) Switching the display
“INFO” button
“SELECT RESET” button To reset the functions below,
press the “SELECT RESET” but-
ton.
• Average Fuel Economy
• Average Speed
• Trip Timer
“SETUP” button
Trip information
Display items can be switched by pressing the “INFO” button.
■ Average Fuel Economy
Displays the average fuel cons umption since the function was
reset. ● The function can be reset by pressing and holding the “SELECT
RESET” button when the average fuel economy is displayed.
● Use the displayed average fuel consumption as a reference.
■ Current Fuel Economy
Displays the current rate of fuel consumption.

1962-2. Instrument cluster
VENZA_OM_OM73030U_(U) ■ Distance to Empty
Displays the estimated maximum di stance that can be driven with
the quantity of fuel remaining. ● This distance is computed based on your average fuel consumption. As
a result, the actual distance that can be driven may differ from that dis-
played.
● When only a small amount of fuel is added to the tank, the display may
not be updated. When refueling, turn the “ENGINE START STOP”
switch off. If the vehicle is refueled without turning the “ENGINE START
STOP” switch off, the display may not be update.
■ Average Speed
Displays the average vehicle sp eed since the function was reset.The function can be reset by pressing and holding the “SELECT RESET”
button when the average speed is displayed.

1972-2. Instrument cluster
2
When driving
VENZA_OM_OM73030U_(U) ■ Tr i p Ti m e r
Displays the elapsed time since the timer was reset. The timer only functions when the engine is running. The timer can be
started and paused by pressing the “SELECT RESET” button, and reset
by pressing and holding the “SELECT RESET” button when the trip timer
is displayed.
The display layout may be customized to show 1 line of trip informa-
tion in the normal font size, 2 lines in the normal font size, or 1 line in
a larger font size. (  P. 200)
When 2 lines of trip information are displayed, it is possible for both of
them to be reset.
Press the “SELECT RESET” button. The first display item that may be reset will be highlighted yellow.
Press the “SELECT RESET” button to select or reset each
display item as described above.
Press the “SETUP” button to change which display items to
reset by highlighting it in yellow. This function only applies if both lines can be adjusted.
Press the “INFO” button to exit the adjusting mode.Press the “INFO” button a second time to switch the display items. STEP 1
STEP 2
STEP 3
STEP 4

1982-2. Instrument cluster
VENZA_OM_OM73030U_(U) Setting up the displays
Press the “SETUP” button wh ile the vehicle is stopped.The “Custom Settings” screen is displayed on the multi-information
display.
If left idle for approximately 10 seconds, the display will revert to the
previous screen.
Select “Display / Clock” by
pressing the “INFO” or “SETUP”
button, and press the “SELECT
RESET” button. If you select “Exit” and press
“SELECT RESET”, the display
will revert to the previous screen.
Select the desired item by press-
ing the “INFO” or “SETUP” but-
ton. Press the “SELECT RESET” but-
ton to enter the setting mode.
The current setting is indicated by
yellow text.STEP 1
STEP 2
STEP 3

1992-2. Instrument cluster
2
When driving
VENZA_OM_OM73030U_(U) ■ Setting the clock
Select “Clock” on the “Display Settings” screen, and press the
“SELECT RESET” button.
Press the “INFO” button to adjust
the hours and the “SETUP” but-
ton to adjust the minutes.
Press and hold the buttons to
adjust the time more quickly. Press the “SELECT RESET” but-
ton to set the clock.
■ Selecting the units
Select “Units” on the “Display Settings” screen, and press the
“SELECT RESET” button.
Select the units you want to read
by pressing the “INFO” or
“SETUP” button. Press the “SELECT RESET” but-
ton to set the units.
The current setting is indicated by
yellow text.STEP 1
STEP 2
STEP 1
STEP 2

2002-2. Instrument cluster
VENZA_OM_OM73030U_(U) ■ Selecting the language
Select “Language” on the “Display Settings” screen, and
press the “SELECT RESET” button.
Select the language you want to
read by pressing the “INFO” or
“SETUP” button. Press the “SELECT RESET” but-
ton to set the language.
The current setting is indicated by
yellow text.
To shortcut directly to the “Lan-
guage” screen from the initial
“Custom Settings” screen, press
and hold the “SETUP” button for
5 seconds.
■ Selecting the trip information layout
Select “Layout” on the “Display Settings” screen, and press
the “SELECT RESET” button.
Select the desired layout by
pressing the “INFO” or “SETUP”
button, and press the “SELECT
RESET” button. The current setting is indicated by
yellow text.STEP 1
STEP 2
STEP 1
STEP 2