2016 TOYOTA MIRAI Quick Reference Guide

7
OVERVIEWHYDROGEN FUEL CELL SYSTEM
& SAFETY FEATURESFEATURES/OPERATIONS
SAFETY AND EMERGENCY FEATURES
* Driver door unlocking function can be programmed to unlock driver door only, or
all doors. Grasping passenger door handle or pushing unlock button on rear hatch
will unlock all doors. (If equipped)
NOTE: Doors may also be locked/unlocked using remote.
UnlockingLocking
Carry remote to unlock Carry remote to lock
Driver door unlock*All-door lock
Back door lock/unlock
Carry remote to
lock/unlock
Touch
Grasp
Push
Lock
Push
Unlock

8
OVERVIEW
Fuel door release button and cap
When the fuel door is open, the fuel cell system will not start. When the
“READY” indicator is on, the fuel door will not open.
Push
Push
Push
Store cap
Replace cap
Light control-Instrument panel
-
+%ULJKWQHVV
control

9
OVERVIEWHYDROGEN FUEL CELL SYSTEM
& SAFETY FEATURESFEATURES/OPERATIONS
SAFETY AND EMERGENCY FEATURES
HYDROGEN FUEL CELL SYSTEM
& SAFETY FEATURES
)XHOFHOOYHKLFOHVHI

10 The Automatic High Beam uses an in-vehicle camera sensor to assess the
brightness of streetlights, the lights of oncoming and preceding vehicles, etc., and
automatically turns high beams on or off as necessary.
To turn the high beams on/off manually, pull the lever to the original position or
press the switch.
Refer to the Owner‘s Manual for more details on this system before attempting
to use it.
Automatic high beams
1) Activate the system2) Press the Automatic High Beam
switch When the fuel cell system is stopped, water is automatically purged from the
tailpipe. To minimize water accumulation in parking garages, etc., purge can be
done manually before parking. While the “READY” indicator is on, press the H2O
switch.
Refer to the Owner‘s Manual for more details on this system before attempting
to use it.
Water release (H2O) switch
HYDROGEN FUEL CELL SYSTEM
& SAFETY FEATURES

11
OVERVIEWHYDROGEN FUEL CELL SYSTEM
& SAFETY FEATURESFEATURES/OPERATIONS
SAFETY AND EMERGENCY FEATURES
While driving on a road that has lane markers, this system recognizes the lane
markers using a camera sensor and alerts the driver when the vehicle deviates
from its lane.
Refer to the Owner‘s Manual for more details on this system before attempting
to use it.
Press the LDA switch (in steering wheel) to turn the LDA system ON, the indicator
will illuminate. Press again to turn OFF.
When the inside of both lane lines turn white:
- Indicates that both right and left lane markers are recognized.
When the inside of either lane line turns white:
- Indicates that the lane marker on the white-marked side is recognized.
When the inside of both lane lines are black:
- Indicates that no lane markers are recognized or the LDA system is temporarily
canceled.
Lane Departure Alert (LDA)
Turning the LDA system ON
Indication on the multi-information display
Camera sensor
Press to ON
Multi-information display

12
HYDROGEN FUEL CELL SYSTEM
& SAFETY FEATURES

Pre-Collision System (PCS)
When a high possibility of a frontal collision is detected by the radar sensor, a
buzzer sounds and a message urging the driver to take evasive action appears
on the multi-information display. If the driver then applies brakes, the system
applies greater brake force in relation to how strongly the brake pedal is
depressed. If the system determines that a collision is unavoidable, the brakes
are automatically applied to reduce the collision speed. The alert timing for the
pre-collision system can be changed or turned on/off, as necessary, by pressing
TRAC switch.
The system is enabled each time the power switch is turned to ON mode.
Refer to the Owner‘s Manual for more details on this system before attempting
to use it.


Each time the Pre-Collision System switch is pressed, the response to the distance
changes as follows:
Far
Middle
Near
Press the TRAC switch for 3 seconds or more.
Changing the pre-collision warning timing
Disabling the Pre-Collision System

13
OVERVIEWHYDROGEN FUEL CELL SYSTEM
& SAFETY FEATURESFEATURES/OPERATIONS
SAFETY AND EMERGENCY FEATURES
Turn the BSM system ON
Blind Spot Monitor (BSM)
The Blind Spot Monitor is a system that has two functions:
• The Blind Spot Monitor function (assists the driver in making the decision when
changing lanes)

14
FEATURES/OPERATIONS
Auto lock/unlock
Automatic door lock functions can be set, or turned OFF.
-Doors lock when shifting to any positions other than P.
-Doors lock when the vehicle speed is approximately 12 mph or higher.
-Doors unlock when shifting into P.
-Doors unlock when the driver’s door is opened.
Refer to the Owner’s Manual for more details.(1) Depress the brake pedal, and
press the “POWER” switch
EULH