2016 SUBARU WRX display

Instruments and controls/Multi function display
! Keyless buzzer volume setting
1. Perform the preparation steps accord-
ing to “ Preparation for car settings ” F 3-83.
2. Operate the “ ” or “ ” switch to
select the “ Keyless Buzzer Volume ” item.
Then push the
button. 3. Select a volume level by operating the
“
” or “ ” switch, and confirm the setting
by pushing the
button.
4. The system will notify you that the
setting is complete.
If the setting is not available, the following
notification will be displayed. In this case,
perform the setting procedure again. ! Hazard warning flasher setting
1. Perform the preparation steps accord-
ing to “ Preparation for car settings ” F 3-83.
2. Operate the “ ” or “ ” switch to
select the “ Hazard Warning Flasher ” item.3-84

Then push the button.
3. The current setting will be displayed.
Push the
button to enter the selection
mode.
4. Select “ On ” or “ Off ” by operating the
“
” or “ ” switch. Then push the button.
5. Select “ Set ” by operating the “ ”
switch, and confirm the setting by pushing
the
button.
6. The system will notify you that the
setting is complete. If the setting is not available, the following
notification will be displayed. In this case,
perform the setting procedure again.
! Defogger setting
1. Perform the preparation steps accord-
ing to “ Preparation for car settings ” F 3-83.Instruments and controls/Multi function display
– CONTINUED –3-85

Instruments and controls/Multi function display
2. Operate the “ ” or “ ” switch to
select the “ Defogger ” item. Then push the
button.
3. The current setting will be displayed.
Push the
button to enter the selection
mode. 4. Select the preferred setting by operat-
ing the “
” or “ ” switch. Then push the
button.
5. Select “ Set ” by operating the “ ”
switch, and confirm the setting by pushing
the
button. 6. The system will notify you that the
setting is complete.
If the setting is not available, the following
notification will be displayed. In this case,
perform the setting procedure again.3-86

! Interior light off delay timer setting
1. Perform the preparation steps accord-
ing to “ Preparation for car settings ” F 3-83.
2. Operate the “ ” or “ ” switch to
select the “ Interior Light ” item. Then push
the
button. 3. The current setting will be displayed.
Push the
button to enter the selection
mode.
4. Select the preferred setting by operat-
ing the “
” or “ ” switch. Then push the
button. 5. Select “ Set ” by operating the “ ”
switch, and confirm the setting by pushing
the
button.
6. The system will notify you that the
setting is complete.
If the setting is not available, the following
notification will be displayed. In this case,
perform the setting procedure again.Instruments and controls/Multi function display
– CONTINUED –3-87

Instruments and controls/Multi function display
! Auto light sensor sensitivity setting
1. Perform the preparation steps accord-
ing to “ Preparation for car settings ” F 3-83.
2. Operate the “ ” or “ ” switch to
select the “ Auto Light Sensor ” item. Then push the
button.
3. The current setting will be displayed.
Push the
button to enter the selection
mode.
4. Select the preferred setting by operat-
ing the “
” or “ ” switch. Then push the button.
5. Select “ Set ” by operating the “ ”
switch, and confirm the setting by pushing
the
button.
6. The system will notify you that the
setting is complete.3-88

If the setting is not available, the following
notification will be displayed. In this case,
perform the setting procedure again.
! Keyless access setting (models
with “ keyless access with push-
button start system ” )
! Preparation for keyless access
settings
1. Perform the preparation steps accord-
ing to “ Preparation for car settings ” F 3-83. 2. Operate the “ ” or “ ” switch to
select the “ Keyless Access Setting ” item.
Then push the
button.
! Driver ’ s door unlock setting
1. Perform the preparation steps accord-
ing to “ Preparation for keyless access
settings ” F 3-89. 2. Operate the “ ” or “ ” switch to
select the “ Driver ’ s Door Unlock ” item.
Then push the
button.
3. The current setting will be displayed.
Push the
button to enter the selection
mode.Instruments and controls/Multi function display
– CONTINUED –3-89

Instruments and controls/Multi function display
4. Select the preferred setting by operat-
ing the “
” or “ ” switch. Then push the
button.
5. Select “ Set ” by operating the “ ”
switch, and confirm the setting by pushing
the
button. 6. The system will notify you that the
setting is complete.
If the setting is not available, the following
notification will be displayed. In this case,
perform the setting procedure again. ! Welcome lighting setting
The leaving time and approaching time
settings can be adjusted.
! Leaving time setting
1. Perform the preparation steps accord-
ing to “ Preparation for car settings ” F 3-83.
2. Operate the “ ” or “ ” switch to
select the “ Welcome Lighting ” item, and
then push the
switch.3-90

3. Select the “ Leaving time set ” by
operating the “
” or “ ” switch, and then
push the
switch.
4. The current setting will be displayed.
Push the
switch to enter the selection
mode. 5. Select the preferred setting by operat-
ing the “
” or “ ” switch, and then push
the
switch.
6. Select “ Set ” by operating the “ ”
switch, and confirm the setting by pushing
the
switch. 7. The system will notify you that the
setting is complete.
If the setting is not available, the following
notification will be displayed. In this case,
perform the setting procedure again.Instruments and controls/Multi function display
– CONTINUED –3-91