2016 Ram 1500 homelink

▫To Accelerate For Passing...............195
PARKSENSE REAR PARK ASSIST — IF
EQUIPPED...........................196
▫ParkSense Sensors.....................196
▫ParkSense Warning Display..............196
▫ParkSense Display.....................197
▫Enabling And Disabling ParkSense.........201
▫Service The ParkSense Rear Park Assist
System.............................202
▫Cleaning The ParkSense System...........203
▫ParkSense System Usage Precautions........203
PARKSENSE FRONT AND REAR PARK ASSIST —
IF EQUIPPED..........................205
▫ParkSense Sensors.....................206▫ParkSense Warning Display..............206
▫ParkSense Display.....................207
▫Enabling And Disabling Front And/Or Rear
ParkSense...........................209
▫Service The ParkSense Park Assist System. . . .210
▫Cleaning The ParkSense System...........211
▫ParkSense System Usage Precautions........211
PARKVIEW REAR BACK UP CAMERA — IF
EQUIPPED...........................214
OVERHEAD CONSOLE — IF EQUIPPED.....217
▫Courtesy/Reading Lights...............217
GARAGE DOOR OPENER — IF EQUIPPED . . .219
▫Before You Begin Programming HomeLink . . .220
▫Programming A Rolling Code............221
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

▫Programming A Non-Rolling Code.........223
▫Canadian/Gate Operator Programming.....225
▫Using HomeLink.....................226
▫Security............................226
▫Troubleshooting Tips...................227
▫General Information....................228
POWER SUNROOF — IF EQUIPPED........228
▫Opening Sunroof — Manual Mode.........230
▫Closing Sunroof — Manual Mode..........230
▫Opening Sunroof — Express..............230
▫Closing Sunroof — Express...............230
▫Pinch Protect Feature...................230
▫Venting Sunroof — Express..............231▫Sunshade Operation....................231
▫Wind Buffeting.......................231
▫Sunroof Maintenance...................231
▫Ignition Off Operation..................232
ELECTRICAL POWER OUTLETS...........232
CIGAR LIGHTER AND ASH RECEIVER — IF
EQUIPPED...........................237
POWER INVERTER — IF EQUIPPED........237
AUXILIARY SWITCHES — IF EQUIPPED.....239
CUPHOLDERS........................239
▫Front Seat Cupholders (40–20–40 Seats)......239
▫Front Instrument Panel Cupholders — Floor
Storage Bin..........................240
▫Rear Cupholders — If Equipped..........
.240
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127

GARAGE DOOR OPENER — IF EQUIPPED
HomeLink replaces up to three hand-held transmitters
that operate devices such as garage door openers, motor-
ized gates, lighting or home security systems. The
HomeLink unit is powered by your vehicles 12 Volt
battery.
The HomeLink buttons that are located in the overhead
console designate the three different HomeLink channels.
NOTE:HomeLink is disabled when the Vehicle Security
Alarm is active.
HomeLink Buttons
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 219

WARNING!
•Your motorized door or gate will open and close
while you are training the universal transceiver. Do
not train the transceiver if people, pets or other
objects are in the path of the door or gate. Only use
this transceiver with a garage door opener that has
a “stop and reverse” feature as required by Federal
safety standards. This includes most garage door
opener models manufactured after 1982. Do not use
a garage door opener without these safety features.
Call toll-free 1-800-355-3515 or, on the Internet at
www.HomeLink.com for safety information or as-
sistance.
•Vehicle exhaust contains carbon monoxide, a dan-
gerous gas. Do not run your vehicle in the garage
while training the transceiver. Exhaust gas can
cause serious injury or death.NOTE:Only use this transceiver with a garage door
opener that has a “stop and reverse” feature as required
by federal safety standards. This includes most garage
door opener models manufactured after 1982. Do not use
a garage door opener without these safety features. Call
toll-free 1-800-355-3515 or, on the Internet at HomeLink-
.com for safety information or assistance.
Before You Begin Programming HomeLink
Ensure your vehicle is parked outside of the garage
before you begin programming.
For efficient programming and accurate transmission of
the radio-frequency signal it is recommended that a new
battery be placed in the hand-held transmitter of the
device that is being programmed to the HomeLink
system.
To erase the channels place the ignition in the ON/RUN
position and push and hold the two outside HomeLink
buttons (I and III) for up to 20 seconds. The Electronic
220 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Vehicle Information Center (EVIC), or Driver Interactive
Display (DID) will display “CLEARING CHANNELS.”
Release the buttons when the EVIC/DID displays
“CHANNELS CLEARED.”
NOTE:
•For vehicle’s equipped with Keyless Enter-N-Go, place
the ignition in the RUN position with the Engine ON.
•Erasing all channels should only be performed when
programming HomeLink for the first time. Do not
erase channels when programming additional buttons.
•If you have any problems, or require assistance, please
call toll-free 1-800-355-3515 or, on the Internet at
HomeLink.com for information or assistance.Programming A Rolling Code
For programming garage door openers that were manu-
factured after 1995. These garage door openers can be
identified by the “LEARN” or “TRAIN” button located
where the hanging antenna is attached to the garage door
opener. It is NOT the button that is normally used to
open and close the door. The name and color of the
button may vary by manufacturer.
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 221

1. Turn the ignition switch to the ON/RUN position.
For vehicle’s equipped with Keyless Enter-N-Go, place
the ignition in the RUN position with the Engine ON.2. Place the hand - held transmitter 1 to 3 inches (3 to 8
cm) away from the HomeLink button you wish to
program.
3. Push and hold the HomeLink button you want to
program while you push and hold the hand - held
transmitter button.
4. Continue to hold both buttons until the EVIC/DID
display changes from “CHANNEL # TRAINING” to
“CHANNEL # TRAINED,” then release both buttons.
NOTE:
•It may take up to 30 seconds or longer in some cases
for the channel to train.
•If the EVIC/DID displays “DID NOT TRAIN” repeat
from Step 2.
5. At the garage door opener motor (in the garage),
locate the “LEARN” or “TRAINING” button. This can
usually be found where the hanging antenna wire is
Training The Garage Door Opener
1 — Door Opener
2 — Training Button 222 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

attached to the garage door opener/device motor.
Firmly push and release the “LEARN” or “TRAIN-
ING” button. On some garage door openers/devices
there may be a light that blinks when the garage door
opener/device is in the LEARN/TRAIN mode.
NOTE:You have 30 seconds in which to initiate the next
step after the LEARN button has been pushed.
6. Return to the vehicle and push the programmed
HomeLink button twice (holding the button for two
seconds each time). The EVIC/DID will display
“CHANNEL # TRANSMIT.” If the garage door
opener/device activates, programming is complete.
NOTE:If the garage door opener/device does not acti-
vate, push the button a third time (for two seconds) to
complete the training.
To program the remaining two HomeLink buttons, repeat
each step for each remaining button. DO NOT erase the
channels.Reprogramming A Single HomeLink Button
(Rolling Code)
To reprogram a channel that has been previously trained,
follow these steps:
1. Cycle the ignition to the ON/RUN position.
2. Push and hold the desired HomeLink button until the
indicator light begins to flash after 20 seconds.Do not
release the button.
3.Without releasing the buttonproceed with “Program-
ming A Rolling Code” step 2 and follow all remaining
steps.
Programming A Non-Rolling Code
For programming Garage Door Openers manufactured
before 1995.
1. Turn the ignition switch to the ON/RUN position.
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 223

2. Place the hand - held transmitter 1 to 3 inches (3 to 8
cm) away from the HomeLink button you wish to
program.
3. Push and hold the HomeLink button you want to
program while you push and hold the hand - held
transmitter button.
4. Continue to hold both buttons until the EVIC/DID
display changes from “CHANNEL # TRAINING” to
“CHANNEL # TRAINED,” then release both buttons.
NOTE:
•It may take up to 30 seconds or longer in some cases
for the channel to train.
•If the EVIC/DID displays “DID NOT TRAIN” repeat
from Step 2.5. Push and hold the programmed HomeLink button.
The EVIC/DID will display “CHANNEL # TRANS-
MIT.” If the garage door opener/device activates,
programming is complete.
To program the remaining two HomeLink buttons, repeat
each step for each remaining button. DO NOT erase the
channels.
Reprogramming A Single HomeLink Button (Non
— Rolling Code)
To reprogram a channel that has been previously trained,
follow these steps:
1. Cycle the ignition to the ON/RUN position.
2. Push and hold the desired HomeLink button until the
indicator light begins to flash after 20 seconds.Do not
release the button.
224 UNDERSTANDING THE FEATURES OF YOUR VEHICLE