Page 28 of 296

26
Access
ReAR RooF FLAP
Support bar
A support bar is provided for 
transporting long loads, after opening 
the rear roof flap.
Fold back the support bar by lifting the 
lever.
g
uide it to the door pillar.
Support the long loads to be 
transported, lift them and reposition the 
support bar with one hand.
e
nsure that it is secured correctly by 
pressing the handle downwards past 
the point of resistance and secure the 
loads firmly. The rear bumper has been 
reinforced to serve as a footrest 
when entering the vehicle.
The rear doors only lock when the 
support bar is installed.
When the rear roof flap is open, take 
care when driving where height is 
restricted.
Never rest loads directly on the rear 
doors.
Comply with the usual indications, to 
warn other drivers.
Reserve the use of the rear roof flap 
for short journeys. The side supports can be used as 
hooking points.
-  
lower the black paddle to secure 
the rear roof flap.
Securing the rear roof flap places it on 
the seal correctly and ensures sealing 
without noise.
This rear roof flap is only compatible 
with side-hinged rear doors.
T
o open the rear roof flap:
-
 
raise the black paddle of the toggle,
-
 
relieve the toggle by pressing the 
rear roof flap (downwards) then 
release the hook,
-
 lift the rear roof flap,
-
 
pass the point of resistance to 
secure the rear roof flap using the 
support stays.
Never drive without the stays in place.
T
o close the rear roof flap:
-
 
check that the support bar is 
secured correctly
,
-
 
lower the rear roof flap,
-
 
while pressing the rear roof flap 
(downwards), take hold of the 
two
 
loops of the spring then place 
the hook in its housing, Never attach any load to the rear roof 
flap.
Never drive without the support bar in 
place.  
     
        
        Page 29 of 296

27
Access
CeNtRAL L o CKIN g
An initial press permits 
central locking of the vehicle, 
when all of the doors are 
closed.
Door open warning lamp
The control switch L
e D:
-  
flashes when the doors are locked with 
the vehicle stationary and the engine off,
- comes on when the doors are locked  
and from the time the ignition is 
switched on.
Anti-intrusion security
If this warning lamp comes 
on, check that all of your 
vehicle's doors are closed 
correctly.
Locking while driving
When the vehicle moves off, as soon 
as you reach approximately 6 mph 
(10
 
km/h), the system locks the doors. 
The characteristic central locking noise 
is heard. The L e D in the switch on 
the dashboard central switch panel 
comes
 
on.
During the journey, opening a door 
results in complete unlocking of the 
vehicle.
Activating / deactivating the 
function
With the ignition on, press 
and hold this switch to 
activate or deactivate the 
function.
Driving with the doors locked may 
make access to the interior more 
difficult in an emergency.
A second press permits central 
unlocking of the vehicle.
The control is inactive when the vehicle 
has been locked using the remote 
control or the key from the outside.
The doors can still be opened from the 
inside. 
ReADY To go
3  
     
        
        Page 51 of 296

49
MANuAL geARB ox
5-speed
6-speed
To change gear easily, always depress 
the clutch pedal fully.
To prevent the mat from becoming 
caught under the pedal:
-
 
ensure that the mat is positioned 
and secured correctly on the floor
,
-
 
never fit one mat on top of another
 .
When driving, avoid leaving your hand 
on the gear knob as the force exerted, 
even if slight, may wear the internal 
components of the gearbox over time.
Changing into 5th or 6th gear
To engage the gear correctly, move the 
gear lever fully to the right.
engaging reverse gear
The lever should be moved slowly 
to reduce noise.
To engage reverse gear, wait until the 
vehicle has come to a complete stop.
SteeRINg WH ee L  ADJ u S t M e N t
When the vehicle is stationary, 
release the steering wheel adjustment 
mechanism by pulling the lever.
Adjust the steering wheel for height 
and reach, then lock the mechanism by 
pushing the lever fully forward. In the 6-speed configuration, raise the 
collar below the gear knob. 
gearbox and steering wheel 
ReADY To go
3  
     
        
        Page 82 of 296
80
Seats
Fully folded position
example of operations for the 
1/3   section. They are identical for the 
2/3
  section. -
 
Raise the grey control bar
 , located 
at the rear of the seat cushion.
-  
T
 ilt the entire seat forward.
Putting back in place
Check that the seat is locked 
on the floor securely when it is 
returned to the sitting position.
-
 
Place the head restraints in the low 
position.
-
 
If necessary
, move the front seats 
forward.
-
 Press the grey control located on 
the upper part of the seat backrest.
-
 
Fold the seat backrest onto the 
seat cushion. T
ilt the entire seat rearwards until it 
locks into place.
Raise the seat backrest.
The seat is locked correctly when the 
control (at the top of the seat back) is 
no longer visible.  
     
        
        Page 84 of 296
82
Seats
ReAR SeAtS  (5  S e At  V e RSI o N ) Head restraint
each seat can be removed individually.
e
ach time a seat is returned to the 
sitting position or after removing then 
refitting a seat, check that it is locked 
on the floor securely.
The three independent rear seats 
are fitted with "comma" shape head 
restraints.
The back of the centre seat, folded 
onto the seat cushion, has a shell 
which serves as a table with cup 
holder. High position: lift and raise the head 
restraint.
Low position: press on the head 
restraint to lower it.
To remove the head restraint, after 
raising it press the tab and lift the head 
restraint.
To install the head restraint, engage 
the rods of the head restraint in the 
holes keeping it in line with the seat 
back.  
     
        
        Page 85 of 296

 83
Seats
Adjusting the angle of the seat backrest
Placing the seat back in the 
table position
Returning the seat back to the sitting position
Placing the seat in the fully 
folded position
Returning the seat to its original position
-  operate the control and adjust the 
angle of the seat backrest.
-
 
Pull the control to fold the seat back 
onto the seat cushion.
Do not place hard or heavy objects 
on the table. 
They could become 
dangerous projectiles in the event of 
sharp braking or impact. -
 
Release the seat back by pullin
 g 
the control, then return it to its 
original position.
When returning the seat backrest to 
the sitting position, ensure that it is 
locked securely.
-
 
Pull the control to place the seat 
back in the table position.
-
 
Raise the bar located behind the 
seat to release the rear anchoring 
points.
-
 
T
 ilt the entire seat forwards, until it 
locks. -
 Push the red control.
-
 
Fold back the seat to fix the rear 
anchoring points.
-
 
Raise the seat backrest by pullin
 g 
the control.
-
 
Check that the seat has correctly 
locked into place.Before unfolding the seat, check 
that no object is obstructing the 
anchorage points or preventing 
correct locking of the seats. 
eASe oF uSe and CoMFoRT
4  
     
        
        Page 87 of 296
 85
Seats
Head restraint
This is of the "comma" shape type.
High position: press the tab, lift and 
raise the head restraint.
Low position: push the tab and press 
the top of the head restraint to lower it.
To remove the head restraint: place it 
in the high position, lift it, then remove 
it.
Store it inside the vehicle, securing it 
firmly.
To install the head restraint: engage 
the rods of the head restraint in the 
holes keeping it in line with the seat 
back.
e
ach seat can be removed and must 
be replaced in the specified position, 
indicated by a symbol on its label.
The seats of row 2 and row 3 are 
independent and adjustable.
ReAR SeAt
S  (7  S e At  V e RSI o N ) 
eASe oF uSe and CoMFoRT
4  
     
        
        Page 89 of 296

 87
Seats
Adjusting the angle of the seat backrest
-  operate the control and adjust the 
angle.
Placing the seat backrest in the 
table position
-
 
Lower the head restraint fully
 .
-
  o perate the control to fold the seat 
back onto the seat cushion. Returning the seat backrest to the 
sitting position
-
 
Release the seat backrest by 
pullin
g the control, then return it to 
its original position.
-   e nsure that it has correctly locked 
into place.
Placing the seat in the fully folded 
position
-  
Place the seat in the table position.
-
 
Pull the red strap, located behind 
the seat, to release the feet of the 
seat from their anchorage on the 
floor
.
-
 
T
 ilt the entire seat forwards.
Row 2 seat adjustmentsReturning the seat to its original 
position
-  u nfold the entire seat.
Before folding the seat, ensure 
that:
-
 
in row 3, no passenger's 
foot is at one of the seat 
anchorages on the floor
,
-
 
the seat is locked securely on 
the floor
,
-
 
the seat belt is available for 
the passenger
. 
eASe oF uSe and CoMFoRT
4