2016 Peugeot Expert VU turn signal

27
Expert_en_Chap01_instruments-de-bord_ed01-2016
Warning / indicator lampStateCause Action / Observations
+
+ SCR emissions
control system
(BlueHDi Diesel)
fixed, on switching
on the ignition,
associated with the
SERVICE and engine
diagnostic warning
lamps, accompanied
by an audible signal
and a message. A fault with the SCR emissions
control system has been detected.
th

is alert disappears once the exhaust emissions
return to normal levels.
flashing, on switching
on the ignition,
associated with the
SERVICE and engine
diagnostic warning
lamps, accompanied by
an audible signal and
a message indicating
the remaining driving
range. After confirmation of the fault with the
emissions control system, you can
drive for up to 650 miles (1 100 km)
before the engine starting inhibition
system is triggered.
Contact a PE
u

g
Eo
t dealer or a qualified workshop
without delay , to avoid a breakdown .
flashing, on switching
on the ignition,
associated with the
SERVICE and engine
diagnostic warning
lamps, accompanied
by an audible signal
and a message. You have exceeded the authorised
driving limit following confirmation
of a fault with the emissions control
system: the engine starting inhibition
system prevents starting of the
engine.
to b

e able to start the engine, you must call on a
PE
u

g
Eo
t dealer or a qualified workshop.
1
Instruments

31
Expert_en_Chap01_instruments-de-bord_ed01-2016
With the engine running, when the needle or
the bar graph (depending on version) is:
-
i
n zone A , the temperature of the engine
coolant is correct,
-

i
n zone B, the temperature of the engine
coolant is too high; the maximum
temperature and the central STOP warning
lamps come on, accompanied by an
audible signal and a warning message in
the touch screen.
You MUST stop as soon as it is safe to do so.
Wait a few minutes before switching off the
engine.
Contact a PE
u

g
Eo
t dealer or a qualified
workshop. After driving for a few minutes, the temperature
and pressure in the cooling system increase.
to t

op up the level:
F
w
ait at least one hour for the engine to
cool,
F
u
nscrew the cap two turns to allow the
pressure to drop,
F
w
hen the pressure has dropped, remove
the cap,
F
t
op up the level to the "MA X" mark.
Be aware of the risk of burns when
topping up the cooling system. Do not
fill above the maximum level (indicated
on the header tank).
Engine coolant temperature Service indicator
System which informs the driver when the
next service is due, in accordance with the
manufacturer's servicing schedule.
th

e point at which the next service is due is
calculated from the last indicator zero reset,
depending on the distance travelled and the
time elapsed since the last service.
For BlueHDi Diesel versions, the degree of
deterioration of the engine oil is also taken into
account (depending on the country of sale).Checking the level
1
Instruments

48
Expert_en_Chap02_ouvertures_ed01-2016
F to activate this selectivity between cab and loading
area , switch the ignition on and
press this button for more than
2


seconds.
Its indicator lamp comes on.
th

e modification is confirmed by an audible
signal and, depending on equipment, the
display of a message. F
t
o
deactivate this selectivity and
return to total unlocking, switch
the ignition on and press this
button for more than 2
seconds.
Its indicator lamp goes off.
By default, selectivity between cab and
loading area is activated.
Total unlocking
Using the remote control
F Press one of these buttons
(depending on equipment) to
unlock the vehicle.
un
locking is signalled by the rapid
flashing of the direction indicators for
about two seconds.
Depending on version, the door mirrors
unfold at the same time. If fitted to your vehicle, pressing
and holding this button allows the
windows to be opened.
t
h
e window
stops when you release the button.
Using the key
Using the remote control with
electric sliding side door(s)
F to totally unlock the
vehicle and open the
side door, press and
hold this button until the
door has opened.
F
t
o


totally unlock the vehicle
without opening the side door,
press this button.
Programming
F to totally unlock the vehicle, turn the key
towards the front of the vehicle.
F
t
h
en to open the door, pull the handle.
If your vehicle has an alarm, this is not
deactivated.
o
p
ening a door will trigger the
alarm, which can then be stopped by switching
the ignition on. Cab
and loading area selectivity
deactivated.
Access

50
Expert_en_Chap02_ouvertures_ed01-2016
Using the remote control
F to unlock the vehicle, press this button.
un

locking is signalled by the rapid
flashing of the direction indicators for
about two seconds.
Depending on version, the door mirrors
unfold at the same time. Driving with the doors locked may
render access for the emergency
services difficult in an emergency.
As a safety measure (children on
board), never leave the vehicle without
taking your remote control, even for a
short period. Ensure that no person or object might
prevent the correct closing of the
windows.
Be particularly aware of children when
operating the windows.
Locking
F to unlock the vehicle totally, turn the key
to the rear of the vehicle.
If your vehicle has an alarm, this will not be
activated.
F
t
o l
ock the vehicle totally , press
this button.
Using the key
If a door is not fully closed (except
the right-hand door with side-hinged
d o o r s):
-

v
ehicle stationary and the engine
running, this warning lamp
comes on, accompanied by an
alert message for a few seconds,
-

v
ehicle moving (speed above
6 mph (10 km/h)), this warning
lamp comes on, accompanied
by an audible signal and an alert
message for a few seconds.
If fitted to your vehicle, pressing
and holding this button closes the
windows.
t
he

window stops when
you release the button.
F
t
o u

nlock the vehicle
and open the side door,
press and hold this
button until the door has
opened.
Using the remote control with
electric sliding side door(s)
Using the remote control
Access

51
Expert_en_Chap02_ouvertures_ed01-2016
Deadlocking
Deadlocking renders the exterior and
interior door controls inoperative.
It also deactivates the manual central
control button.
th
erefore, never leave anyone inside
the vehicle when it is deadlocked.
to d

eadlock the vehicle:
F
t
u
rn the key to the rear of the vehicle.
F
t
hen
within five seconds , turn the key to
the rear again. Depending on version, the door mirrors
fold at the same time.
Using the remote control
to lock the vehicle:
F
P
ress this button.
F
t
hen
within five seconds after
locking , press this button again.
If your vehicle is not fitted with an alarm,
deadlocking is signalled by the fixed
illumination of the direction indicators
for about two seconds.
to d

eadlock the vehicle:
Using the key
If your vehicle is not fitted with an
alarm, locking is confirmed by the fixed
illumination of the direction indicators
for about two seconds.
According to version, the door mirrors
fold at the same time.
If one of the openings (doors or boot) is
still open, the central locking does not
take place.
When the vehicle is locked, if it is
unlocked inadvertently, it will lock itself
again automatically after about thirty
seconds unless a door is opened.
And if your vehicle has an alarm, this
will be reactivated (with volumetric
monitoring, even if this had been
deactivated).
th

e folding and unfolding of the door
mirrors by the remote control can be
deactivated by a PE
u

g
Eo
t dealer or a
qualified workshop.
2
Access

55
Expert_en_Chap02_ouvertures_ed01-2016
"Keyless Entry and
Starting"
It allows the central locking or unlocking of the
vehicle from a distance.
It is also used to locate and start the vehicle, as
well as providing protection against theft.
Remote control
this separation of cab and loading
area locking provide security in use.
It allows you to prevent access to the
part of the vehicle where you are not
present.
What is the point
of total or selective
unlocking?
total unlocking allows all of the vehicle's doors
(front, side and rear) to be unlocked.
Selective unlocking allows either the cab
doors, or the loading area doors (side and
rear) to be unlocked. F
t
o a
ctivate this selectivity
between cab and loading
area , switch the ignition on and
press this button for more than
2


seconds.
Its indicator lamp comes on.
th

e modification is confirmed by an audible
signal and, depending on equipment, the
display of a message. F
t
o
deactivate this selectivity and
return to total unlocking, switch
the ignition on and press this
button for more than 2
seconds.
Its indicator lamp goes off.
By default, selectivity between cab and
loading area is activated.
Programming
2
Access

68
Expert_en_Chap02_ouvertures_ed01-2016
B a c k- u p c o nt r o l (s)
If the alarm is activated, the audible
signal triggered on opening a door
with the key (integral with the remote
control) will stop when the ignition is
switched on.
Integral key
Locking the driver's door
Unlocking
F Insert the integral key into the door lock, then turn it to the front.
If your vehicle has an alarm, it will not
be deactivated/activated on unlocking/
locking the vehicle.
op

ening a door will trigger the alarm,
which can be stopped by switching the
ignition on.
to d

eadlock the vehicle, turn the key
again within five seconds of locking.
Locking the front passenger door
F open the door.
Unlocking
F use the interior door handle.
It is used to lock and unlock the vehicle when
the remote control cannot operate:
-

c

ell battery flat, vehicle battery discharged
or disconnected, ...
-

v

ehicle located in an area with strong
electromagnetic signals.
F

P

ress and hold button 1 to extract the
integral key 2 . F

I

nsert the integral key into the door lock,
then turn it to the rear. F
R
emove the cap on on the edge of the
d o o r.
F
I
nsert the key into the latch aperture
(without forcing) and turn the assembly.
F
R
emove the key and refit the cap.
F
C
lose the door and check from the outside
that the vehicle has locked correctly.
Access

149
Expert_en_Chap04_eclairage-et-visibilite_ed01-2016
Front daytime running
lamps
(light-emitting diodes)
they come on automatically when the engine
is started, when the lighting control stalk is in
position "0" or " AUTO ".
Automatic illumination of
headlamps
Activation
When a low level of ambient light is detected
by a sunshine sensor, the number plate
lamps,


sidelamps and dipped beam headlamps
are switched on automatically, without any
action on the part of the driver.
t
h
ey can also
come on if rain is detected, at the same time as
automatic operation of the windscreen wipers.
As soon as the brightness returns to a
sufficient level or after the windscreen wipers
are switched off, the lamps are switched off
automatically.
Deactivation
F turn the ring to another position. Deactivation of the function is
accompanied by the display of a message.
Operating fault
In the event of a malfunction of the
sunshine sensor, the lighting comes
on; this warning lamp is displayed
Contact a PE
u

g
Eo
t dealer or a qualified
workshop. in the instrument panel accompanied by an
audible signal and/or a message.
In fog or snow, the sunshine sensor
may detect sufficient light. In this
case, the lighting will not come on
automatically.
Do not cover the sunshine sensor,
coupled with the rain sensor and
located in the top of the windscreen
behind the rear view mirror; the
associated functions would no longer
be controlled.
F
t
u

rn the ring to the "AUTO" position.
t
h

e
activation of the function is accompanied
by the display of a message.
4
Lighting and visibility