2016 Peugeot Boxer fog light

4
boxer_en_Chap01_Vue-ensemble_ed01-2015
InStruMEntS And controLS
1. Fusebox.
2. Additional programmable heating.
3.

Cruise control / sped limiter controls. 4.

V ehicle configuration / Headlamp beam
height / Front/rear foglamps.
5.

Lighting and direction indicator

control
stalk.
6.

Instrument panel with screen.7.

Wiper / screenwash / trip computer
control stalk.
8.

Ignition switch.
9.


Driver's front airbag / Horn.
10.


Steering mounted audio system

controls.
Presentation

8
boxer_en_Chap01_Vue-ensemble_ed01-2015
InStruMEntS And controLS
Instrument panels, screens, speedometer 23
W
arning lamps, indicator
lamps

24-31g

auges, indicators
32, 35g

ear shift indicator
36-37
Lighting controls


45-47
Automatic illumination of headlamps


46g

uide-me-home lighting

46
Parking lamps


47
Opening the bonnet


127
Dashboard fuses


145-146
V

ehicle configuration

87-89
Setting the time


88
Headlamp beam height adjustment

47
Front/rear fog lamps

45
Pneumatic suspension


96-97
Stop & Start


40-42 Front/rear wipers


48
Screenwash/headlamp wash


48trip computer


92
Starter

, ignition switch
38
Hill start


39
Cruise control


49-51, 52-54
Speed limiter


55-57
Fixed speed limiter


58
Instruments and controls

4-5Steering wheel, reach adjustment 37
Horn
99
Steering mounted radio controls

186, 233
Mirrors, electric windows


85-86
Locking the load space


22
Additional heating, rear air
conditioning


65-66
Programmable additional heating


67-70
Location

12
boxer_en_Chap01_Vue-ensemble_ed01-2015
Eco-drIVInG
o ptimise the use of your gearbox
With a manual gearbox, move off gently and change up without
waiting. While accelerating changing up early. If your vehicle has
the system, the gear shift indicator invites you to engage the most
suitable gear; follow its instructions as soon as it is displayed in
the instrument panel.
drive smoothly
Maintain a safe distance between vehicles, use engine
braking rather than the brake pedal, and press the accelerator
progressively.
t
hese practices contribute towards a reduction in
fuel consumption and CO
2 emissions and also helps reduce the
background traffic noise.
If your vehicle has cruise control, make use of the system at
speeds above 20 mph (30 km/h) when the traffic is flowing well.
control the use of your electrical equipment
Before moving off, if the passenger compartment is too warm,
ventilate it by opening the windows and air vents before using the
air conditioning.
Above 30 mph (50 km/h), close the windows and leave the air
vents open.
Remember to make use of equipment that can help keep the
temperature in the passenger compartment down (window
blinds...).
Switch off the air conditioning, unless it has automatic digital
regulation, as soon as the desired temperature is attained.
Switch off the demisting and defrosting controls, if not automatic.
Switch off the heated seat as soon as possible.
Switch off the headlamps and front foglamps when the level of
light does not require their use.
e

co-driving is a range of everyday practices that allow the motorist to o\
ptimise their fuel consumption and CO
2 emissions.
Avoid running the engine before moving off, particularly in winter;
your vehicle will warm up much faster while driving.
As a passenger, if you avoid connecting your multimedia devices
(film, music, video game...), you will contribute towards limiting the\

consumption of electrical energy, and so of fuel.
Disconnect your portable devices before leaving the vehicle.
Motoring & the environment

29
boxer_en_Chap02_Pret-a-Partir_ed01-2015
Warning/indicator lampisindicates Solution - action
Diesel
pre-heater on.the ambient temperature
necessitates pre-heating. Wait until the lamp goes off before operating the starter.
Dipped beam on.a manual selection.
turn the lighting control stalk ring to the second


position.
Main beam that the control stalk has been
pulled towards you.Pull the lighting control stalk again to return to dipped
beam.
Direction
indicators flashing with
buzzer.a change of direction using the
lighting stalk.
to the Right: press the stalk upwards.
to the Left: press the stalk downwards.
Front foglamps on.that the button on the MOD

e

control panel has been pressed. Manual selection.t

he foglamps only operate if the dipped beam
headlamps are on.
Rear foglamps on.that the button on the MOD
e

control panel has been pressed. Manual selection.


t

he lamps only operate if the dipped beam headlamps
are on. When visibility is normal, please switch them off.
Cruise control on.that the cruise control has been
selected. Manual selection.
"
e ase of use and comfort - Steering mounted controls"
section.
Instruments and controls
2
rEAdY to SEt oFF

45
boxer_en_Chap03_ergo-et-confort_ed01-2015
LIGHtInG controL StALK
Selection is by rotation of the white mark on
the ring.
direction indicators (green
flashing)
Left: downwards.
Right: upwards.
Sidelamps on
d

ipped/main beam
headlamps on
Switching between dipped and main
beam
Pull the control stalk fully towards you.
Headlamp flash
Pull the control stalk towards you,
regardless of the position of the ring.
Front foglamps
r

ear foglamps
If your vehicle is fitted with foglamps, these
operate with the dipped or main beam
headlamps.
Press one of these controls to switch on the
lamps.
t

he foglamps should only be used in
fog or when snow is falling.
In clear weather or in rain, both day and
night, rear foglamps dazzle and their use is
prohibited.
Do not forget to switch them off when they
are no longer necessary."Motorway" function
Pull the lever towards the steering wheel with
a press, without passing the point of resistance
of the lighting stalk; the corresponding direction
indicators will flash five times.
3
EASE oF uSE and coMFort
Steering mounted controls

46
boxer_en_Chap03_ergo-et-confort_ed01-2015
AutoMAtI c ILL u MI n At I on
Activation
turn the ring to this position.
Do not cover the sunshine sensor at
the top centre of the windscreen.
GuIdE-ME-HoME LIGHtInG
Ignition off or key in the StoP position.
Within 2 minutes after switching of f the
engine, position the ignition key in the S
t
OP

position or remove it.
Pull the lighting stalk towards the steering
wheel.
t

he indicator lamp comes on in
the instrument panel.
e

ach action on the lighting stalk,
pulled towards the steering
wheel, prolongs the guide me home
lighting by 30 seconds up to approximately
3
minutes. When this time has elapsed, the
lamps are switched off automatically.
Deactivate this control by keeping the stalk
pulled towards the steering wheel for more
than 2 seconds. If your vehicle is fitted with this function:
when you leave your vehicle, the dipped
beam headlamps remain on for the selected
duration (when leaving a car park for
example).
You can adjust the sensitivity of the
sunshine sensor.
Refer to the "
t
echnology on board -


Vehicle configuration" section.
If your vehicle is fitted with this function, the
dipped beam headlamps are switched on
automatically if the light is poor.
In fog or snow, the sunshine sensor may
detect sufficient light.
t

herefore, the lamps
will not be switched on automatically. If
necessary, you must switch on the dipped
beam headlamps manually.t
hey are switched off when the light returns
to a sufficient level.
LEd dAYtIME runnInG LAMPS
On starting the vehicle, in daylight the LeD
daytime running lamps come on automatically .
If the sidelamps and headlamps are switched
on manually or automatically, the daytime
running lamps go off.
Programming
For countries where exterior lighting by
day is not a legal requirement, you can
activate or deactivate the function via the
configuration menu.
t

he lamps are switched off automatically
when the ignition is switched off.
Steering mounted controls

146
boxer_en_Chap08_Aide-Rapide_ed01-2015
FusesA (amps) Allocation
12 7.5Right-hand dipped headlamp
13 7.5Left-hand dipped headlamp
31 5
e

ngine compartment control unit relay - Dashboard control unit relay (ig\
nition switch +)
32 7.5Cabin lighting (battery +)
33 7.5Battery check sensor on Stop & Start version (battery +)
34 7.5Minibus interior lighting - Hazard warning lamps
36 10Audio system - Air conditioning controls - Alarm -
tachograph - Battery cut-of

f control unit -
Additional heating programmer (battery +)
37 7.5Brake lamp switch -
t

hird brake lamp - Instrument panel (ignition +)
38 20Central door locking (battery +)
42 5ABS control unit and sensor - ASR sensor - DSC sensor - Brake lamp switch
43 20Windscreen wiper motor (ignition switch +)
47 20Driver's electric window motor
48 20Passenger's electric window motor
49 5Parking sensors control unit - Audio system - Steering mounted controls - Centre and side switch panels\
-
Auxiliary switch panel - Battery cut-off control unit (ignition switch +)
50 7.5Airbags and pre-tensioners control unit
51 5
tachograph - Power steering control unit -

Air conditioning - Reversing lamps - Water in Diesel sensor -
Air flow sensor (ignition switch +)
53 7.5Instrument panel (battery +)
89 -Not used
90 7.5Left-hand main beam
91 7.5Right-hand main beam
92 7.5Left-hand front foglamp
93 7.5Right-hand front foglamp
Failed fuse

151
boxer_en_Chap08_Aide-Rapide_ed01-2015
Halogen bulbs must be changed after
the headlamp has been off for several
minutes (risk of serious burns). Do not touch
the bulb directly with your fingers, use a
lint-free cloth.
When each operation has been completed,
check the operation of the lamps.
5 - Front foglamps
type E

, H11 - 55 W
-
t
urn the steering so that the wheel


on the side in question is turned fully
inwards.
-

Remove the screw located in the wheel


arch.
-

Remove the protective cover

.
LE
d
daytime running lamps
t

hese light-emitting diode (L
e
D) lamps
serve as both daytime running lamps and
sidelamps.
If your vehicle is fitted with L
e
D daytime
running lamps, contact a P
euge
O
t
dealer

.
4 - Sidelamps / daytime running lamps
type A

, W21/5W - 21W and 5W
-

Remove the cover by pulling on the


rubber tongue.
-
t
urn the bulb holder a quarter of a turn


anti-clockwise.
-

Change the bulb.
-


Remove the fixing clip and disconnect

the electrical connector.
-
t
urn and disengage the bulb holder
.
-

Change the bulb taking care to align the

metal part with the grooves on the lamp.
Failed bulb or lamp
QuICK HeLP
8