2016 NISSAN NOTE Display

DIAGNOSIS SYSTEM (TCM)TM-95
< SYSTEM DESCRIPTION > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
LINE PRESSURE SEN (V) ×Displays the signal voltage of the line pressure sensor.
ATF TEMP SEN (V) ×Displays the signal voltage of the CVT fluid temperature
sensor.
G SENSOR (V) ×Displays the signal voltage of the G sensor.
VIGN SEN (V) ×Displays the battery voltage applied to TCM.
VEHICLE SPEED (km/h or mph)× Displays the vehicle speed recognized by TCM.
INPUT REV (rpm) Displays the input shaft speed of CVT recognized by
TCM.
PRI SPEED (rpm)× Displays the primary pulley speed recognized by TCM.
SEC SPEED (rpm) Displays the secondary pulley speed recognized by
TCM.
OUTPUT REV (rpm) Displays the output shaft speed of CVT recognized by
TCM.
ENG SPEED (rpm)× Displays the engine speed recognized by TCM.
SLIP REV (rpm)× Displays the speed difference between the input shaft
speed of CVT and the engine speed.
TOTAL GEAR RATIO ×Displays the total CVT gear ratio calculated from input
shaft speed/output shaft speed of CVT.
PULLEY GEAR RATIO ×Displays the pulley gear ratio calculated from primary
pulley speed/secondary pulley speed.
AUX GEARBOX Displays the gear position of the auxiliary gearbox recog-
nized by TCM.
G SPEED (G) Displays the acceleration and deceleration speed of the
vehicle calculated from vehicle speed change.
ACCEL POSI SEN 1 (deg)×× Displays the estimated throttle position received through
CAN communication.
VENG TRQ (Nm)× Display the engine torque recognized by TCM.
PRI TRQ (Nm) Display the input shaft torque of CVT.
TRQ RTO Display the torque ratio of torque converter.
LINE PRESSURE (MPa)× Displays the secondary pressure (line pressure) calcu-
lated from the signal voltage of the secondary pressure
sensor.
FLUID TEMP (°C or °F) × Displays the CVT fluid temperature calculated from the
signal voltage of the CVT fluid temperature sensor.
DSR REV (rpm) Displays the target primary pulley speed calculated from
processing of gear shift control.
TRGT GEAR RATIO Displays the target gear ratio from the input shaft to the
output shaft of CVT calculated from processing of gear
shift control.
TGT PLLY GR RATIO Displays the target gear ratio of the pulley from process-
ing of gear shift control.
TRGT AUX GEARBOX Displays the target gear of the auxiliary gearbox calculat-
ed from processing of gear shift control.
LU PRS (MPa) Displays the target oil pressure of the torque converter
clutch solenoid valve calculated from oil pressure pro-
cessing of gear shift control.
Monitored item
(Unit)Monitor item selection
Remarks
MAIN SIG-
NALS ECU IN-
PUT SIG-
NALS
Revision: August 2015 2016 Versa Note

cardiagn.com

TM-96
< SYSTEM DESCRIPTION >[CVT: RE0F11A]
DIAGNOSIS SYSTEM (TCM)
LINE PRS
(MPa) Displays the target oil pressure of the line pressure sole-
noid valve calculated from oil pressure processing of
gear shift control.
TRGT PRI PRESSURE (MPa) Displays the target oil pressure of the primary pressure
solenoid valve calculated from oil pressure processing of
gear shift control.
TRGT HC/RB PRESS (MPa) Displays the target oil pressure of the high clutch & re-
verse brake solenoid valve calculated from oil pressure
processing of gear shift control.
TRGT LB PRESSURE (MPa) Displays the target oil pressure of the low brake solenoid
valve calculated from oil pressure processing of gear
shift control.
ISOLT1 (A)× Displays the command current from TCM to the torque
converter clutch solenoid valve.
ISOLT2 (A) ×Displays the command current from TCM to the line
pressure solenoid valve.
PRI SOLENOID (A)× Displays the command current from TCM to the primary
pressure solenoid valve.
HC/RB SOLENOID (A)× Displays the command current from TCM to the high
clutch& reverse brake solenoid valve.
L/B SOLENOID (A)× Displays the command current from TCM to the low
brake solenoid valve.
SOLMON1 (A)×× Monitors the command current from TCM to the torque
converter clutch solenoid valve and displays the moni-
tored value.
SOLMON2 (A)×× Monitors the command current from TCM to the line
pressure solenoid valve and displays the monitored val-
ue.
PRI SOL MON (A)×× Monitors the command current from TCM to the primary
pressure solenoid valve and displays the monitored val-
ue.
HC/RB SOL MON (A)×× Monitors the command current from TCM to the high
clutch& reverse brake solenoid valve and displays the
monitored value.
L/B SOL MON (A)×× Monitors the current command from TCM to the low
brake solenoid valve and displays the monitored value.
D POSITION SW (On/Off) ×Displays the operation status of the transmission range
switch (D position).
N POSITION SW (On/Off) ×Displays the operation status of the transmission range
switch (N position).
R POSITION SW (On/Off) ×Displays the operation status of the transmission range
switch (R position).
P POSITION SW (On/Off) ×Displays the operation status of the transmission range
switch (P position).
BRAKESW (On/Off)×× Displays the reception status of the stop lamp switch sig-
nal received through CAN communication.
L POSITION SW (On/Off) ×Displays the operation status of the transmission range
switch (L position).
IDLE SW (On/Off)×× Displays the reception status of the closed throttle posi-
tion signal received through CAN communication.
SPORT MODE SW (On/Off)×× Displays the reception status of the overdrive control
switch signal received through CAN communication.
Monitored item
(Unit)Monitor item selection
Remarks
MAIN SIG-
NALS ECU IN-
PUT SIG-
NALS
Revision: August 2015 2016 Versa Note

cardiagn.com

DIAGNOSIS SYSTEM (TCM)TM-97
< SYSTEM DESCRIPTION > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
STRDWNSW (On/Off) ו Displays the operation status of the paddle shifter
(down switch).
• It is displayed although not equipped.
STRUPSW (On/Off) ו Displays the operation status of the paddle shifter (up
switch).
• It is displayed although not equipped.
DOWNLVR (On/Off) ו Displays the operation status of the selector lever
(down switch).
• It is displayed although not equipped.
UPLVR (On/Off) ו Displays the operation status of the selector lever (up
switch).
• It is displayed although not equipped.
NONMMODE (On/Off) ו Displays if the selector lever position is not at the man-
ual shift gate.
• It is displayed although not equipped.
MMODE (On/Off) ו Displays if the selector lever position is at the manual
shift gate.
• It is displayed although not equipped.
INDLRNG (On/Off) Displays the transmission status of the shift position (L
position) signal transmitted through CAN communica-
tion.
INDDRNG (On/Off) Displays the transmission status of the shift position (D
position) signal transmitted through CAN communica-
tion.
INGNRNG (On/Off) Displays the transmission status of the shift position (N
position) signal transmitted through CAN communica-
tion.
INGRRNG (On/Off) Displays the transmission status of the shift position (R
position) signal transmitted through CAN communica-
tion.
INGPRNG (On/Off) Displays the transmission status of the shift position (P
position) signal transmitted through CAN communica-
tion.
CVT LAMP (On/Off) Displays the transmission status of the OD OFF indicator
lamp signal transmitted through CAN communication.
SPORT MODE IND (On/Off) Displays the transmission status of the OD OFF indicator
lamp signal transmitted through CAN communication.
MMODE IND (On/Off) • Displays the transmission status of the manual mode
signal transmitted through CAN communication.
• It is displayed although not equipped.
VDC ON (On/Off) ו Displays the reception status of the VDC (ESP) oper-
ation signal received through CAN communication.
• It is displayed although not equipped.
TCS ON (On/Off) ו Displays the reception status of the TCS operation sig-
nal received through CAN communication.
• It is displayed although not equipped.
ABS FAIL SIGNAL (On/Off) ×Displays the reception status of the ABS malfunction sig-
nal received through CAN communication.
ABS ON (On/Off) ×Displays the reception status of the ABS operation signal
received through CAN communication.
RANGE ×Displays the gear position recognized by TCM.
M GEAR POS ×Display the target gear of manual mode
Monitored item
(Unit)Monitor item selection
Remarks
MAIN SIG-
NALS ECU IN-
PUT SIG-
NALS
Revision: August 2015 2016 Versa Note

cardiagn.com

TM-98
< SYSTEM DESCRIPTION >[CVT: RE0F11A]
DIAGNOSIS SYSTEM (TCM)
WORK SUPPORT
*: “Clutch point learning” can
be selected, but do not use it.
Engine brake adjustment
Check the degradation level of the CVT fluid.
G SEN SLOPE (%) Displays the gradient angle calculated from the G sensor
signal voltage.
ENGBRKLVL (On/Off) Displays the setting of “ENGINE BRAKE ADJ” in “Work
Support”.
PVIGN VOLT (V) ×Displays the backup voltage of TCM.
TRGT AUX GR RATIO Displays the target gear ratio of the auxiliary gearbox cal-
culated from processing of gear shift control.
G SEN CALIBRATION (YET/DONE) Displays the status of “G
SENSOR CALIBRATION” in
“Work Support”.
N IDLE STATUS (On/Off) Displays idle neutral status.
CVT-B • Displays CVT fluid temperature count.
• This monitor item does not use.
CVT-A • Displays CVT fluid temperature count.
• This monitor item does not use.
Monitored item
(Unit)Monitor item selection
Remarks
MAIN SIG-
NALS ECU IN-
PUT SIG-
NALS
Item name Description
ENGINE BRAKE ADJ. Although there is no malfunction on the transaxle and the CVT system, if a customer
make a complaint like “I do not feel comfortable with automatic operation of the engine
brake on downhill”, the engine brake may be cancelled with “engine brake adjust-
ment”.
CONFORM CVTF DETERIORTN Check the degradation level of the CVT fluid under severe conditions.
G SENSOR CALIBRATION Compensate the G sensor.
ERASE CALIBRATION DATA Erase the calibration data memorized by TCM.
ERASE LEARNING VALUE Erase the learning value me morized by TCM.
ERASE MEMORY DATA Perform “erasing of the calibration data” and “erasing of the learned value” at the same
time.
CLUTCH POINT LEARNING* Allow learning of the clutch engagement point of the auxiliary gearbox for TCM.
ENGINE BRAKE LEVEL
ON : Turn ON the engine brake control.
OFF : Turn OFF the engine brake control.
CVTF degradation level data
210,000 or more : Replacement of the CVT fluid is required.
Less than 210,000 : Replacement of the CVT fluid is not required.
Revision: August 2015 2016 Versa Note

cardiagn.com

TCM
TM-99
< ECU DIAGNOSIS INFORMATION > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
ECU DIAGNOSIS INFORMATION
TCM
Reference ValueINFOID:0000000012431033
CONSULT DATA MONITOR STANDARD VALUE
• In CONSULT, electric shift timing or lock-up timing, i. e. operation timing of each solenoid valve, is displayed.
Therefore, if there is an obvious difference between t he shift timing estimated from a shift shock (or engine
speed variations) and that shown on the CONSULT, the mechanism parts (including the hydraulic circuit)
excluding the solenoids and sensors may be malfunctioning. In this case, check the mechanical parts follow-
ing the appropriate diagnosis procedure.
• Shift point (gear position) displayed on CONSULT slight ly differs from shift pattern described in Service Man-
ual. This is due to the following reasons.
- Actual shift pattern may vary slightly within specified tolerances.
- While shift pattern described in Service Manual indica tes start of each shift, CONSULT shows gear position
at end of shift.
- The solenoid display (ON/OFF) on CONSULT is changed at the start of gear shifting. In contrast, the gear
position display is changed at the time when gear shif ting calculated in the control unit is completed.
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Monitor item ConditionValue/Status (Approx.)
VSP SENSOR While driving Almost same as the speedometer display.
ESTM VSP SIG While driving Almost same as the speedometer display.
PRI SPEED SEN In driving (lock-up ON) A value obtained from dividing engine
speed by counter gear ratio
SEC REV SENSOR Auxiliary gearbox: 1GR
Approximately twice the “VHCL/S SE
(REV)”
Auxiliary gearbox: 2GR Almost same as the “VHCL/S SE (REV)”
VHCL/S SE (REV) Auxiliary gearbox: 1GR
Approximately half of the “SEC REV SEN-
SOR”
Auxiliary gearbox: 2GR Almost same as the “SEC REV SENSOR”
ENG SPEED SIG Engine running Almost same reading as tachometer
LINE PRESSURE SEN • Selector lever: “N” position
•At idle
0.88 – 0.92 V
AT F T E M P S E N CVT fluid: Approx. 20
°C (68 °F) 2.01 – 2.05 V
CVT fluid: Approx. 50 °C (122 °F) 1.45 – 1.50 V
CVT fluid: Approx. 80 °C (176 °F) 0.90 – 0.94 V
G SENSOR Vehicle is level 2.5 V
VIGN SEN Ignition switch: ON 10 – 16 V
VEHICLE SPEED While driving Almost same as the speedo meter display.
INPUT REV In driving (lock-up ON) Almost same as the engine speed.
PRI SPEED In driving (lock-up ON) A value obtained from dividing engine
speed by counter gear ratio
SEC SPEED Auxiliary gearbox: 1GR
Approximately twice the “OUTPUT REV”
Auxiliary gearbox: 2GR Almost same as “OUTPUT REV”
OUTPUT REV Auxiliary gearbox: 1GR
Approximately half of “SEC SPEED”
Auxiliary gearbox: 2GR Almost same as “SEC SPEED”
ENG SPEED Engine running Almost same reading as tachometer
SLIP REV While driving Engine speed − Input speed
Revision: August 2015 2016 Versa Note

cardiagn.com

TM-100
< ECU DIAGNOSIS INFORMATION >[CVT: RE0F11A]
TCM
TOTAL GEAR RATIOAuxiliary gearbox: 1GR
Counter gear ratio
×Pulley ratio Auxiliary
gearbox gear ratio
Auxiliary gearbox: 2GR Counter gear ratio ×Pulley ratio
PULLEY GEAR RATIO In driving (forward)
2.20 − 0.55
In driving (reverse) 2.20
AUX GEARBOX Vehicle started with selector lever in “L” position
1st
Release the accelerator pedal after the follow-
ing conditions are satisfied
• Selector lever: “D” position
• Accelerator pedal position: 1/8 or less
• Vehicle speed: 50 km/h (31 MPH) or more 2nd
In gear shifting of auxiliary gearbox 1st ⇔ 2nd
G SPEED Vehicle stopped
0.00 G
During acceleration The value changes to the positive side
along with acceleration.
During deceleration The value changes to the positive side
along with deceleration.
ACCEL POSI SEN 1 Accelerator pedal released
0.00 deg
Accelerator pedal fully depressed 80.00 deg
VENG TRQ While driving The value changes along with acceleration/
deceleration.
PRI TRQ While driving The value changes along with acceleration/
deceleration.
TRQ RTO While driving The value changes along with acceleration/
deceleration.
LINE PRESSURE Selector lever: “P” position 0.575 MPa
FLUID TEMP Ignition switch ON. Displays the CVT fluid temperature.
DSR REV While driving It varies along with the driving condition.
TRGT GEAR RATIO While driving It varies along with the driving condition.
TGT PLLY GR RATIO In driving (forward)
2.20 − 0.55
In driving (reverse) 2.20
TRGT AUX GEARBOX Vehicle started with selector lever in “L” position
1st
Release the accelerator pedal after the follow-
ing conditions are satisfied
• Selector lever: “D” position
• Accelerator pedal position: 1/8 or less
• Vehicle speed: 50 km/h (31 MPH) or more 2nd
In gear shifting of auxiliary gearbox Display gear position after gear shifting
LU PRS • Engine started
• Vehicle is stopped.
−
0.500 MPa
• Selector lever: “D” position
• Accelerator pedal position: 1/8 or less
• Vehicle speed: 20 km/h (12 MPH) or more 0.450 MPa
LINE PRS • After engine warm up
• Selector lever: “N” position
•At idle
0.500 MPa
• After engine warming up
• Selector lever: “D” position
• Depress the accelerator pedal fully 4.930 – 5.430 MPa
TRGT PRI PRESSURE • Selector lever: “L” position
• Vehicle speed: 20 km/h (12 MPH) 0.325 MPa
Monitor item
ConditionValue/Status (Approx.)
Revision: August 2015 2016 Versa Note

cardiagn.com

TM-110
< ECU DIAGNOSIS INFORMATION >[CVT: RE0F11A]
TCM
DTC Index
INFOID:0000000012431037
NOTE:
• If multiple malfunction codes are detected at the same time, check each code according to the “DTC check
priority list”. TM-109, "
DTC Inspection Priority Chart".
• The ignition counter is displayed in “FFD”. Refer to TM-93, "
CONSULT Function".
2P0740 TORQUE CONVERTER
TM-167
P0743 TORQUE CONVERTERTM-169
P0962 PC SOLENOID ATM-184
P0963 PC SOLENOID ATM-186
P0966 PC SOLENOID BTM-189
P0967 PC SOLENOID BTM-191
P0998 SHIFT SOLENOID FTM-193
P0999 SHIFT SOLENOID FTM-195
P099B SHIFT SOLENOID GTM-197
P099C SHIFT SOLENOID GTM-199
3P0890 TCM TM-182
4P062F EEPROM
TM-143
P0705 T/M RANGE SENSOR ATM-144
P0706 T/M RANGE SENSOR ATM-150
P0711 FLUID TEMP SENSOR ATM-153
P0712 FLUID TEMP SENSOR ATM-157
P0713 FLUID TEMP SENSOR ATM-159
P0715 INPUT SPEED SENSOR ATM-161
P0847 FLUID PRESS SEN/SW BTM-177
P0848 FLUID PRESS SEN/SW BTM-179
P1586 G SENSORTM-201
P1588 G SENSORTM-204
P2765 OUTPUT SPEED SENSORTM-206
5P0720 OUTPUT SPEED SENSOR TM-164
6P0746 PC SOLENOID A
TM-173
P2857 CLUTCH B PRESSURETM-209
P2858 CLUTCH A PRESSURETM-210
P2859 CLUTCH A PRESSURE TM-211
P285A CLUTCH B PRESSURETM-213
7P0744 TORQUE CONVERTER
TM-171P0846 FLUID PRESS SEN/SW BTM-175
P0965 PC SOLENOID BTM-188
PriorityDTC (Diagnostic Trouble Code) Reference
DTC*1, *2
Items
(CONSULT screen terms) Trip MILPermanent
DTC
group
*3Reference
GST CONSULT
(TRANSMISSION)
P062F P062F EEPROM 1ON B TM-143
P0705P0705 T/M RANGE SENSOR A 2ON B TM-144
P0706P0706 T/M RANGE SENSOR A 2ON B TM-150
P0711P0711 FLUID TEMP SENSOR A 2ON A TM-153
Revision: August 2015 2016 Versa Note

cardiagn.com

ADDITIONAL SERVICE WHEN REPLACING TCMTM-125
< BASIC INSPECTION > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
ADDITIONAL SERVICE WHEN REPLACING TCM
DescriptionINFOID:0000000012431042
When replacing the TCM, perform the following work. For work procedure, refer to TM-125, "Work Procedure".
TCM PROGRAMMING• Since vehicle specifications are not yet written in a new TCM, it is necessary to write them with CONSULT.
CAUTION:
When replacing TCM, save TCM data on CONSULT before removing TCM.
LOADING AND STORING OF CALIBRATION DATA• The TCM acquires calibration data (individual characteristic value) of each solenoid that is stored in the
ROM assembly (in the control valve). This enables the TCM to perform accurate control. After the TCM is
replaced, check that the calibrati on data is correctly loaded and stored.
CALIBRATION OF G SENSOR
• TCM stores calibration data (inherent characteristic value) of G sensor to provide accurate control. There-
fore, it is required to perform calibration of G sensor after the replacement of TCM.
CAUTION:
When replacing TCM and transaxle assembly simultaneously, replace transaxle assembly first and
then replace TCM.
Work ProcedureINFOID:0000000012431043
1.CHECK NEW TCM PART NUMBER
Check new TCM part number to see whether it is blank TCM or not.
NOTE:
• Part number of blank TCM is 310F6-XXXXX.
• Check the part number when ordering TCM or with the one included in the label on the container box.
Is the new TCM a blank TCM?
YES >> GO TO 2.
NO >> GO TO 3.
2.SAVING TCM DATA (VEHICLE SPECIFICATIONS)
NOTE:
Save necessary data stored in TCM in CONSULT according to the following instructions: With CONSULT
1. Turn ignition switch OFF.
2. Turn ignition switch ON.
3. Select “Re/programming, Configuration”.
4. Select “AT/CVT”.
NOTE:
If “AT/CVT” is not displayed and TCM data cannot be saved on CONSULT, GO TO 3.
5. Select “Programming”.
6. Save TCM data on CONSULT according to the CONSULT display.
>> GO TO 3.
3.REPLACE TCM
1. Turn ignition switch OFF and wait for 10 seconds.
2. Replace TCM. Refer to TM-239, "
Removal and Installation".
>> GO TO 4.
4.LOAD CALIBRATION DATA
1. Shift the selector lever to the “P” position.
2. Turn ignition switch ON.
3. Check that "P" is displayed on shift position indicator on combination meter. NOTE:
Revision: August 2015 2016 Versa Note

cardiagn.com