2016 NISSAN NOTE key

FUEL FILLER LID OPENERDLK-307
< REMOVAL AND INSTALLATION > [WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
FUEL FILLER LID LOCK : Removal and InstallationINFOID:0000000012430283
REMOVAL
1. Fully open fuel filler lid.
2. Remove luggage side lower finisher (LH). Refer to INT-34, "
LUGGAGE SIDE LOWER FINISHER :
Removal and Installation".
3. Disconnect the harness connector from the fuel filler lid lock assemby.
4. Release pawls (A) and remove fuel filler lid lock assembly (1). CAUTION:
Be careful not to damage gasket (2) when removing.
5. Disconnect fuel filler lid opener cable (1) by pulling downward and then sliding cable end to the side to remove from fuel filler
lid lock assembly (2).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, check fuel filler lid assembly open/close, lock/unlock operation.
JMKIA8138ZZ
JMKIA8139ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-308
< REMOVAL AND INSTALLATION >[WITHOUT INTELLIGENT KEY SYSTEM]
DOOR SWITCH
DOOR SWITCH
Removal and InstallationINFOID:0000000012430284
REMOVAL
1. Remove the door switch bolt (A).
2. Disconnect the harness connector and remove door switch (1).
INSTALLATION
Installation is in the reverse order of removal.
JMKIA2173ZZ
Revision: August 2015
2016 Versa Note

cardiagn.com

REMOTE KEYLESS ENTRY RECEIVERDLK-309
< REMOVAL AND INSTALLATION > [WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
REMOTE KEYLESS ENTRY RECEIVER
Removal and InstallationINFOID:0000000012430285
REMOVAL
1. Remove glove box assembly. Refer to IP-25, "Removal and Installation".
2. Remove remote keyless entry receiver bolt (A).
3. Disconnect the harness connector and remove remote keyless entry receiver (1)
INSTALLATION
Installation is in the reverse order of removal.
JMKIA7947ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-310
< REMOVAL AND INSTALLATION >[WITHOUT INTELLIGENT KEY SYSTEM]
KEYFOB BATTERY
KEYFOB BATTERY
Removal and InstallationINFOID:0000000012430286
REPLACEMENT
1. Remove screw from the rear of keyfob.
2. Place the key with the lower case facing up. Use a suitable tool wrapped with tape between upper case
and lower case and separate the lower case from the upper case.
CAUTION:
• Do not touch the circuit board or battery termi nal. Doing so could cause the keyfob to malfunc-
tion
• The keyfob is water-resistant. However, if it does get wet, immediately wipe it dry.
3. When replacing the circuit board assembly, remove circuit board assembly from the upper case.
[Circuit board assembly: Switch rubber + Board surface]
CAUTION:
Do not touch the printed circuits directly.
4. Remove the battery from the lower case and replace it.
CAUTION:
When replacing battery, keep dirt, grease, and other foreign materials off the electrode contact
area.
5. After replacement, fit the lower and upper cases together and tighten with the screw. CAUTION:
After replacing the battery, Be sure to check that door locking operates normally using the keyfob.
Refer to DLK-247, "
ComponentFunctionCheck".
Battery replacement : Coin-type lithium battery
(CR1620)
Revision: August 2015 2016 Versa Note

cardiagn.com

STEERING LOCK UNITDLK-311
< REMOVAL AND INSTALLATION > [WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
STEERING LOCK UNIT
Exploded ViewINFOID:0000000012828149
NOTE:
Steering lock unit and key cylinder are serviced as an a ssembly. Ignition switch is available separately.
Removal and Installation - Steering lock unitINFOID:0000000012828150
REMOVAL
1. Disconnect battery cables. Refer to PG-70, "Removal and Installation (Battery)".
2. Remove combination switch. Refer to BCS-138, "
Removal and Installation".
3. Remove cluster lid A. Refer to IP-21, "
Removal and Installation".
4. Disconnect the harness connector from the spiral cable.
5. Disconnect the harness connector from the ignition switch.
ALKIA4124ZZ
1. Steering lock bracket 2. Steering column 3. Ignition switch
4. Steering lock unit 5. NATS antenna amp. A. Tamper resistant self-shear type screw
B. Key cylinder Front
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-312
< REMOVAL AND INSTALLATION >[WITHOUT INTELLIGENT KEY SYSTEM]
STEERING LOCK UNIT
6. Disconnect the harness connector from the key switch.
7. For models with CVT but without intelligent key system,
perform the following steps to separate key inter-
lock cable from steering lock unit:
a. Lift lock plate (A) in the direction of the arrow ( C) and remove in the direction of the arrow ( D).
b. Disconnect the key interlock cable from the steering lock unit.
8. Using suitable tool, remove tamper resistant self-shear type screw. CAUTION:
Do not reuse screw. Replace with new tamper resistant self-shear type screw.
9. Remove steering lock bracket and steering lock unit.
10. Remove NATS antenna amp. (if necessary). Refer to SEC-159, "
Removal and Installation".
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse screw. Replace with new tamper resistant self-shear type screw.
• Tighten tamper resistant self-shear type screw until head breaks off.
• Adjust the neutral position of the steering angle sensor. Refer to BRC-55, "
ADJUSTMENT OF STEERING
ANGLE SENSOR NEUTRAL POSITION : Description".
• For initialization and registration of mechanical keys, refer to CONSULT Immobilizer mode and follow the on-
screen instructions.
Removal and Installation - Ignition switchINFOID:0000000012828152
REMOVAL
1. Remove steering column cover. Refer to IP-17, "Removal and Installation".
2. Disconnect ignition switch harness connector.
3. Remove ignition switch screws and ignition switch.
INSTALLATION
Installation is in the reverse order of removal.
Adjust the neutral position of t he steering angle sensor. Refer to BRC-55, "
ADJUSTMENT OF STEERING
ANGLE SENSOR NEUTRAL POSITION : Description".
(1) :Key interlock cable
(B) :Steering lock unit
JSDIA1798ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

EM-34
< REMOVAL AND INSTALLATION >[HR16DE]
OIL PAN AND OIL STRAINER
OIL PAN AND OIL STRAINER
Exploded ViewINFOID:0000000012431709
Removal and Installation (Lower Oil Pan)INFOID:0000000012431710
REMOVAL
WARNING:
• Be careful not to get bu
rned, engine coolant and engine oil may be hot.
• Prolonged and repeated contact with used engi ne oil may cause skin cancer; avoid direct skin con-
tact with used oil. If skin contact is made, wash thoroughly with soap or hand cleaner as soon as
possible.
1. Drain engine oil. Refer to LU-8, "
Draining".
1. Rear oil seal 2. O-ring 3. Oil pan (upper)
4. Oil pump chain tensioner (for oil pump drive chain) 5. Oil pump drive chain
6. Crankshaft key
7. Crankshaft sprocket 8. Oil pump sprocket9. Oil pump
10. O-ring 11. O-ring 12. Oil pan drain plug
13. Drain plug washer 14. Oil pan (lower) 15. Oil filter
16. Connector bolt 17. Oil cooler 18. O-ring
19. Relief valve A. Refer to EM-37, "
Removal and In-
stallation (Upper Oil Pan)"
B. Refer to LU-10, "Removal and Instal-
lation"
C. Oil pan (lower) side
AWBIA1595ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

TIMING CHAINEM-51
< REMOVAL AND INSTALLATION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EM
NP
O
TIMING CHAIN
Exploded ViewINFOID:0000000012431718
Removal and InstallationINFOID:0000000012431719
CAUTION:
The rotation direction indicated in the t
ext is as viewed from the engine front.
NOTE:
• When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from
spilling.
• When removing the camshafts, the oil pump drive chain does not need to be removed.
REMOVAL
1. Timing chain slack guide 2. Timing chain tensioner3. Camshaft sprocket (EXH)
4. Camshaft sprocket (INT )5. Plug 6. Front oil seal
7. Crankshaft pulley 8. Crankshaft pulley bolt9. Front cover
10. Crankshaft sprocket 11. Crankshaft sprocket key 12. Oil pump sprocket
13. Oil pump drive chain 14. Oil pump drive chain tensioner 15. Timing chain
16. Timing chain tension guide A. Refer to INSTALLATION
AWBIA1475ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com