2016 NISSAN NOTE remote control

BCS-124
< BASIC INSPECTION >[WITHOUT INTELLIGENT KEY SYSTEM]
CONFIGURATION (BCM)
>> GO TO 4.
4.OPERATION CHECK
Confirm that each function controlled by BCM operates normally.
>> WORK END
Configuration ListINFOID:0000000012432398
CAUTION:
• Thoroughly read and understand the vehicle speci fication. ECU control may not operate normally if
the setting is not correct.
• The “setting value” of this vehicle is as follows: Never select any other value than the setting value
shown below. (If there is only 1 item in “setting value” that means that item is the only choice for this
certain vehicle.)
⇔ : Items which confirm vehicle specifications SETTING ITEM
NOTE
Items Setting value
CAN CONNECTION UNIT MODE4 ⇔ WITHOUT • MODE4: With CVT
• WITHOUT: Without CVT
KEYLESS ENTRY WITH ⇔ WITHOUT • WITH: With remote keyless entry
• WITHOUT: Without remote keyless entry
AUTO LOCK & UNLOCK FUNC WITH ⇔ WITHOUT • WITH: With auto door lock function
• WITHOUT: With auto door lock function
Revision: August 2015
2016 Versa Note

cardiagn.com

DLK-6
REMOTE KEYLESS ENTRY SYSTEM : System
Diagram .................................................................
199
REMOTE KEYLESS ENTRY SYSTEM : System
Description .............................................................
199
DIAGNOSIS SYSTEM (BCM) ..........................201
COMMON ITEM ..................................................... ..201
COMMON ITEM : CONSULT Function (BCM -
COMMON ITEM) ...................................................
201
DOOR LOCK .......................................................... ..202
DOOR LOCK : CONSULT Function (BCM -
DOOR LOCK) ........................................................
202
MULTI REMOTE ENT ............................................ ..202
MULTI REMOTE ENT : CONSULT Function
(BCM - MULTI REMOTE ENT) ..............................
203
ECU DIAGNOSIS INFORMATION .............205
BCM, IPDM E/R .............................................. .205
List of ECU Reference ......................................... ..205
WIRING DIAGRAM ....................................206
POWER DOOR LOCK SYSTEM .................... .206
Wiring Diagram .................................................... ..206
REMOTE KEYLESS ENTRY SYSTEM ...........216
Wiring Diagram .................................................... ..216
BASIC INSPECTION ..................................225
DIAGNOSIS AND REPAIR WORKFLOW ...... .225
Work Flow ............................................................ ..225
INSPECTION AND ADJUSTMENT .................228
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT ..................................................... ..
228
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Description ............................. ..
228
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Special Repair Requirement ....
228
DTC/CIRCUIT DIAGNOSIS ...................... ..229
U1000 CAN COMM ......................................... .229
Description ........................................................... ..229
DTC Logic ..............................................................229
Diagnosis Procedure .............................................229
U1010 CONTROL UNIT (CAN) .......................230
DTC Logic ............................................................ ..230
Diagnosis Procedure .............................................230
POWER SUPPLY AND GROUND CIRCUIT ...231
BCM ........................................................................ ..231
BCM : Diagnosis Procedure ..................................231
DOOR SWITCH ...............................................232
Description ........................................................... ..232
Component Function Check ............................... .232
Diagnosis Procedure .............................................232
Component Inspection ..........................................234
DOOR LOCK AND UNLOCK SWITCH ............235
DRIVER SIDE ......................................................... .235
DRIVER SIDE : Description ..................................235
DRIVER SIDE : Component Function Check ......235
DRIVER SIDE : Diagnosis Procedure ...................235
PASSENGER SIDE .................................................236
PASSENGER SIDE : Descripti on .........................236
PASSENGER SIDE :
Component Function Check ............................... .
236
PASSENGER SIDE : Diagnosis Procedure ..........237
KEY CYLINDER SWITCH ................................239
Description ........................................................... .239
Component Function Check .................................239
Diagnosis Procedure .............................................239
Component Inspection ..........................................240
KEY SWITCH (BCM INPUT) ............................241
Diagnosis Procedure ............................................ .241
DOOR LOCK ACTUATOR ...............................242
DRIVER SIDE ......................................................... .242
DRIVER SIDE : Description ..................................242
DRIVER SIDE : Component Function Check ......242
DRIVER SIDE : Diagnosis Procedure ...................242
PASSENGER SIDE .................................................243
PASSENGER SIDE : Descripti on .........................243
PASSENGER SIDE :
Component Function Check ............................... .
243
PASSENGER SIDE : Diagnosis Procedure ..........243
REAR LH ................................................................ .244
REAR LH : Description .........................................244
REAR LH : Component Function Check ............ .244
REAR LH : Diagnosis Procedure ..........................244
REAR RH ................................................................ .245
REAR RH : Description .........................................245
REAR RH : Component Function Check .............245
REAR RH : Diagnosis Procedure .........................246
REMOTE KEYLESS ENTRY RECEIVER ........247
Description ........................................................... .247
Component Function Check ................................247
Diagnosis Procedure .............................................247
KEYFOB BATTERY AND FUNCTION .............250
Description ........................................................... .250
Component Function Check ................................250
Diagnosis Procedure .............................................250
HORN FUNCTION ............................................252
Description ........................................................... .252
Component Function Check ................................252
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-22
< SYSTEM DESCRIPTION >[WITH INTELLIGENT KEY SYSTEM]
SYSTEM (INTELLIGENT KEY SYSTEM)
SYSTEM (INTELLIGENT KEY SYSTEM)
INTELLIGENT KEY SYSTEM
INTELLIGENT KEY SYSTEM : System DescriptionINFOID:0000000012429983
SYSTEM DIAGRAM
SYSTEM DESCRIPTION
• The Intelligent Key system is a system that makes it
possible to lock and unlock the door locks (door lock/
unlock function) by carrying the Intelligent Key, which operates based on the results of electronic ID verifica-
tion using two-way communication between the Intelligent Key and the vehicle (BCM).
NOTE:
The driver should always carry the Intelligent Key.
• The settings for each function can be changed with CONSULT.
• If an Intelligent Key is lost, a new Intelligent Key can be registered. A maximum of 4 Intelligent Keys can be
registered.
• It is possible to perform a diagnosis on the syst em and register an Intelligent Key with CONSULT.
• For initialization and registration of Intelligent Keys, refer to CONSULT Immobilizer mode and follow the on-
screen instructions.
ALKIA3645GB
Function DescriptionRefer
Door lock Lock/unlock can be performed by pressing the request switch. DLK-23
Remote keyless entryLock/unlock can be performed by pressing the remote controller button of the
Intelligent Key.
DLK-25
Revision: August 2015
2016 Versa Note

cardiagn.com

SYSTEM (INTELLIGENT KEY SYSTEM)DLK-23
< SYSTEM DESCRIPTION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
DOOR LOCK FUNCTION
DOOR LOCK FUNCTION : System DescriptionINFOID:0000000012429984
SYSTEM DIAGRAM
DOOR REQUEST SWITCH OPERATION
When pressing the request switch, it is possible to lock and unlock the door by carrying the Intelligent Key.
OPERATION DESCRIPTION
• When the BCM detects that each door request switch is pressed, it starts the outside key antenna and inside
key antenna corresponding to the pressed door request swit ch and transmits the request signal to the Intelli-
gent Key. And then, check that the Intelligent Key is near the door.
• If the Intelligent Key is within the outside key antenna detection area, it receives the request signal and
transmits the key ID signal to the BCM via remote keyless entry receiver.
• BCM receives the key ID signal and compares it with the registered key ID.
• BCM transmits door lock/unlock signal and operates each door lock actuator. At the same time, BCM blinks
hazard warning lamp (lock: 2 times, unlock: 1 time) and sounds Intelligent Key buzzer (lock: 1 time, unlock:
1 time) as a reminder.
OPERATION CONDITION
If the following conditions are satisfied, door lock/unl ock operation is performed if the door request switch is
operated:
Key reminder The key reminder buzzer sounds a warning if the door is locked with the key left
inside the vehicle. DLK-27
WarningIf an action that does not meet the operating condition of the Intelligent Key sys-
tem is taken, the buzzer sounds to inform the driver.
DLK-27
Engine start
The engine can be turned on while carrying the Intelligent Key. DLK-22
Interior room lamp control Interior room lamp is controlled according to door lock/unlock state. DLK-20
FunctionDescriptionRefer
JMKIA6137GB
Revision: August 2015 2016 Versa Note

cardiagn.com

SYSTEM (INTELLIGENT KEY SYSTEM)DLK-25
< SYSTEM DESCRIPTION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
REMOTE KEYLESS ENTRY FUNCTION
REMOTE KEYLESS ENTRY FUNCT ION : System DescriptionINFOID:0000000012429985
SYSTEM DIAGRAM
REMOTE KEYLESS ENTRY OPERATION
The Intelligent Key has the same functions as the remote control entry system. Therefore, it can be used in the
same manner as the remote controller by operating the door lock/unlock button.
Remote keyless entry system contro ls operation of the following items:
• Auto door lock
• Door lock/unlock
• Hazard and buzzer reminder
OPERATION AREA
To check that the Intelligent Key works normally, us e within 1 m (3 ft) range of each door, however the opera-
ble range may differ according to surroundings.
DOOR LOCK/UNLOCK FUNCTION
• When door lock/unlock button of the Intelligent Key is pressed, lock signal or unlock signal is transmitted from Intelligent Key to BCM via remote keyless entry receiver.
• BCM receives the signal and compares it with the registered key ID to the vehicle.
• BCM transmits door lock/unlock signal to each door lock actuator and operates each door lock actuator,
when key ID matches. At the same time, BCM blinks hazard warning lamps (lock: 2 times, unlock: 1 time)
and sounds Intelligent Key buzzer (lock: 1 time) as a reminder.
OPERATION CONDITION
Door lock function
Intelligent Key
Remote keyless entry receiver
Door switch
Door request switch
Door lock actuator
Inside key antenna
Outside key antenna
Intelligent Key warning buzzer
CAN communication system
BCM
Hazard warning lamp
Push-button ignition switch
Combination meter
Door lock/unlock function ××××××× ×
Hazard and buzzer reminder function ×××× ×
Auto door lock function ××××× × × ×
ALKIA3195GB
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-26
< SYSTEM DESCRIPTION >[WITH INTELLIGENT KEY SYSTEM]
SYSTEM (INTELLIGENT KEY SYSTEM)
HAZARD AND BUZZER REMINDER FUNCTION
For the operation check, BCM blinks hazard warning lamps (lock: 2 times, unlock: 1 time) and sounds Intelli-
gent Key warning buzzer (lock: 1 time) when door lock or unlock operates by each remote controller button
operation of Intelligent Key.
How to Change Hazard and Buzzer Reminder Mode
Refer to
BCS-22, "INTELLIGENT KEY : CONSULT Func tion (BCM - INTELLIGENT KEY)".
AUTO DOOR LOCK FUNCTION
After door is unlocked by Intelligent Key button operati on and if 30 seconds or more passes without performing
the following operation, all doors are automatically locked. However, operation check function does not acti-
vate.
Auto door lock mode can be changed by the “AUTO LOCK SET” in “Work support”. Refer to BCS-22, "
INTEL-
LIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)".
LIST OF OPERATION RELATED PARTS
Parts marked with × are the parts related to operation.
KEY REMINDER FUNCTION
Remote controller operation Operation condition
Lock • All door are closed.
• Ignition switch is in the LOCK or OFF position.
• P position warning is not activated.
Unlock • Ignition switch is in the LOCK or OFF position.
• Intelligent Key is outside the vehicle.
• P position warning is not activated.
Operating condition
• Door switch is ON. (door is open)
• BCM receives lock signal.
• Push switch is pressed.
Remote keyless entry functions
Intelligent Key
Remote keyless entry receiver
Door switch
Door lock actuator
Push-button ignition switch
Intelligent Key warning buzzer
CAN communication system
BCM
Combination meter
Hazard warning lamp
IPDM E/R
Horn
Door lock/unlock function by remote control button
××××××
Hazard and buzzer reminder function ×××××××
Auto door lock function ××××××
Revision: August 2015 2016 Versa Note

cardiagn.com

COMPONENT PARTSDLK-193
< SYSTEM DESCRIPTION > [WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
SYSTEM DESCRIPTION
COMPONENT PARTS
REMOTE KEYLESS ENTRY SYSTEM
REMOTE KEYLESS EN TRY SYSTEM : Component Parts LocationINFOID:0000000012430155
A. View with glove box door removed B. View of LH door switch (RH similar)
No. Component Function
1. Combination meter Combination meter transmits the vehicle speed sig-
nal to BCM via CAN communication.
BCM also receives the vehicle speed signal from
ABS actuator and electric unit (control unit) via CAN
communication. BCM compares both signals to de-
tect the vehicle speed.
Security indicator lamp is located on combination
meter.
Security indicator lamp blinks when ignition switch
is in any position other than ON to warn that NIS-
SAN VEHICLE IMMOBILIZER SYSTEM-NATS
[NVIS (NATS)] is on board.
Refer to
MWI-9, "
METER SYSTEM : Combination
Meter" (Type A) or MWI-59, "METER SYSTEM :
Combination Meter" (Type B).
2. Ignition switch Ignition switch transmits ON/OFF signal to BCM.
BCM maintains the ignition switch position status.
ALKIA3211ZZ
Revision: August 2015
2016 Versa Note

cardiagn.com

DLK-194
< SYSTEM DESCRIPTION >[WITHOUT INTELLIGENT KEY SYSTEM]
COMPONENT PARTS
REMOTE KEYLESS ENTRY SYSTEM : Fron t Door Lock Assembly (Driver Side)
INFOID:0000000012430156
• Door lock actuator and unlock sensor are Integrated in front door
lock assembly LH.
• Door lock actuator receives lock/unlock signal from BCM, and then locks/unlocks driver door.
• Only front door lock assembly LH integrates unlock sensor. Unlock sensor transmits lock/unlock status of driver door to BCM.
3. BCM Then, when the ignition switch is turned ON, BCM
performs ID verification between BCM and ECM. If
the ID verification result is OK, ECM can start en-
gine.
Refer to BCS-77, "
BODY CONTROL SYSTEM :
Component Parts Location" for detailed installation
location.
4. Main power window and door lock/unlock switch Door lock and unlock switch is integrated into the
main power window and door lock/unlock switch.
Door lock and unlock switch transmits door lock/un-
lock operation signal to BCM.
Refer to PWC-7, "
Main Power Window And Door
Lock/Unlock Switch".
5. Front door lock assembly LH Door key cylinder switch is integrated into front door
lock assembly (driver side).
Door key cylinder switch detects door LOCK/UN-
LOCK operation using mechanical key, and then
transmits the operation signal to BCM.
Refer to DLK-194, "
REMOTE KEYLESS ENTRY
SYSTEM : Front Door Lock Assembly (Driver
Side)".
6. Rear door lock actuator LH Rear door lock actuator locks/unlocks the rear door
latch assembly.
7. Back door lock actuator Back door lock actuator locks/unlocks the back door
latch assembly. Refer to
DLK-195, "
REMOTE KEY-
LESS ENTRY SYSTEM : Back Door Lock Assem-
bly".
8. Remote keyless entry receiver Remote keyless entry receiver receives button op-
eration signal and key ID signal of Intelligent Key,
and them transmits them to the BCM.
Refer to DLK-195, "
REMOTE KEYLESS ENTRY
SYSTEM : Remote Keyless Entry Receiver".
9. Door switch Door switch detects door open/close condition and
then transmits ON/OFF signal to BCM. Refer to
DLK-195, "
REMOTE KEYLESS ENTRY SYSTEM :
Door Switch".
No.
Component Function
JMKIA8649ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com