2016 MITSUBISHI SHOGUN clock

Vehicles with aluminium wheels
Tighten the wheel nuts (flange nuts) un-
til their flange section comes in contact with the wheel and is no longer loose.CAUTIONl Never apply oil to either the wheel bolts or
the nuts, or they will tighten too much.NOTEl Flange nuts can be temporarily used on the
steel wheel as shown in the illustration, but return to the original wheel and tyre as soonas possible.
l If all four aluminium wheels are changed to
steel wheels, use tapered nuts.
10. Put the notch (J) provided on the jack
handle end on the valve (K) of the jack.
Using the jack handle, turn the release
valve anticlockwise slowly to lower thevehicle until the tyre touches the ground.WARNINGl Be sure to open the release valve slowly. If
it is opened quickly, the vehicle will drop
abruptly and the jack may come out of
position, causing a serious accident.
11. Tighten the nuts crisscross in 2 or 3
steps until each nut has been tightened
securely.

How to change a tyre
8-14OVWE16E1For emergencies8

Tightening torque
105 to 125 Nm
(Achieved by applying a force of 390
to 460 N at the end of the wheel nut wrench supplied with the vehicle.)CAUTIONl Never use your foot or a pipe extension for
extra force in the wheel nut wrench. If you
do so, you will tighten the nut too much.
12. Lower the jack all the way and remove
it.
CAUTIONl If the release valve is loosened too much (2
or more turns) in the anticlockwise direction, the jack’s oil will leak and the jack cannotbe used.CAUTIONl Close the release valve slowly when lower-
ing the vehicle, or the valve may be dam-
aged.NOTEl Occasionally when the vehicle is jacked up,
the grooved portion of the designated pointwill not come off. When this happens, rock
the vehicle to lower the ram.
l If the jack is difficult to remove by hand, in-
sert the jack handle (L) into the bracket (M).Then using the handle, remove the jack.
13. Press the piston down all the way, and
turn the release valve clockwise as far as possible.
14. Check your tyre inflation pressure at the
next gasstation. The correct pressures
are shown on the driver’s door label. See the illustration.
15. On vehicles with tyre pressure monitor-
ing system (TPMS), after filling your tyres to the correct pressure, reset the tyre pressure monitoring system(TPMS).
Refer to “Tyre pressure monitoring sys-
tem (TPMS): Reset of low tyre pressure
warning threshold” on page 6-56.
CAUTIONl After changing the tyre and driving the vehi-
cle about 1,000 km (620 miles), retighten the
wheel nuts to make sure that they have not come loose.
l If the steering wheel vibrates when driving
after changing the tyre, we recommend you to have the tyres checked for balance.
How to change a tyre
8-15OVWE16E1For emergencies8

1-High-mounted stop lamp (bulb type)*:
16 W (W16W)
2- Licence plate lamps: 5 W (W5W)
3- Rear fog lamp: 21 W (W21W)
4- Tail lamps*: 5 W (W5W)
5- Rear turn-signal lamps*: 21 W
(WY21W)
6- Rear turn-signal lamps*: 21 W
(WY21W)
7- Stop and tail lamps*: 21/5 W (W21/5W) Stop lamps*: 21/5 W (W21/5W)
8- Reversing lamps: 21 W (W21W)
Codes in parentheses indicate bulb
types.NOTEl On vehicles with LED type high-mounted
stop lamp, do not attempt to repair or replaceit.
For repair and replacement, contact a
MITSUBISHI MOTORS Authorized Serv-
ice Point.Inside
E01003403118
1- Luggage compartment lamp: 8 W
2- Door courtesy lamps: 3.4 W
3- Vanity mirror lamps* 2 W
4- Room & map lamps: 8 W
5- Rear personal lamps: 8 W
6- Glove box lamp: 1.4 W
Headlamps
E01003501199
Replacement of high-beam
1. Remove the bulb and connector assem-
bly (A) by turning it anticlockwise.
2. Depress the tab (B) on the harness con-
nector and pull the harness connector
(C) to remove it.
Replacement of lamp bulbs
10-26OVWE16E1Maintenance103-door models5-door models
Rear

3.To install the bulb, perform the removal
steps in reverse.
Replacement of low beam (ex-
cept for vehicles with discharge
headlamps)
1. Remove the bulb and connector assem-
bly (A) by turning it anticlockwise.
2. Depress the tab (B) on the harness con-
nector and pull the harness connector
(C) to remove it.
3. To install the bulb, perform the removal
steps in reverse.
CAUTIONl Handle halogen lamp bulbs with care. The
gas inside halogen lamp bulbs is highly pres- surized, so dropping, knocking, or scratching
a halogen lamp bulb can cause it to shatter.
l Never hold the halogen lamp bulb with a
bare hand, dirty glove, etc.
The oil from your hand could cause the bulb to break the next time the headlamps are op-
erated. If the glass surface is dirty, it must be cleaned with alcohol, paint thinner, etc., andrefit it after drying it thoroughly.Position lamps (except for vehi-
cles with discharge headlamps)
E01003702332
1. Turn the bulb socket anticlockwise to re-
move it.
2. Remove the bulb from the socket by
pulling out.
3. To install the bulb, perform the removal
steps in reverse.
Replacement of lamp bulbs
10-27OVWE16E1Maintenance10

Front turn-signal lamps
E01003800733
1. Turn the bulb socket anticlockwise to re-
move it.
2. Remove the bulb from the socket by
pulling out.
3. To install the bulb, perform the removal
steps in reverse.
Front fog lamps*
E01004002983
1. Remove the 5 clips (A, C) and screw (B)
by following procedures then turn up the cover (D).
2. Depress the tab (E) on the harness con-
nector (F) and pull the harness connector
to remove it.
3. Remove the entire socket and bulb as-
sembly (G) by turning it anticlockwise.CAUTIONl Handle halogen lamp bulbs with care. The
gas inside halogen lamp bulbs is highly pres-
surized, so dropping, knocking, or scratching
a halogen lamp bulb can cause it to shatter.
l Never hold the halogen lamp bulb with a
bare hand, dirty glove, etc.
The oil from your hand could cause the bulb to break the next time the fog lamps are op- erated. If the glass surface is dirty, it must becleaned with alcohol, paint thinner, etc., and
refit it after drying thoroughly.
Replacement of lamp bulbs
10-28OVWE16E1Maintenance10

4.To install the bulb, perform the removal
steps in reverse.
NOTEl When refitting the clips (H and I) of the cov-
er, push the pin (J).Rear combination lamps
E01004200659
On corner side
1. Remove the screws that hold the lamp
unit.
2. Slide the lamp unit out sideways to re-
move it.
Left sideRight side3. Remove the socket and bulb assemblies
by turning them anticlockwise. Remove the bulb by pulling it out.3-door models5-door models
A- Rear turn-signal lamp* B- Stop and tail lamp* Stop lamp*
C- Reversing lamp
4. To install the bulb, perform the removal
steps in reverse.
Replacement of lamp bulbs
10-29OVWE16E1Maintenance10

On bumper*
1. Remove the lens mounting screws.
2.Remove the socket and bulb assembly
together by turning it anticlockwise, and then remove the bulb by pulling it out.
D- Rear turn-signal lamp
E- Tail lamp
3. To install the bulb, perform the removal
steps in reverse.
Rear fog lamp
E01004100371
1. Open the spare wheel garnish (A). (Re-
fer to “To remove the spare wheel” on
page 8-10).
2. Remove the socket and bulb assembly
(B) by turning it anticlockwise, and then remove the bulb by pulling it out.
3. To install the bulb, perform the removal
steps in reverse.High-mounted stop lamp (bulb
type)*
E01004500535
1. Insert a straight blade (or minus) screw-
driver with a cloth over at the edge of
the cover and pry gently to remove the cover.
Replacement of lamp bulbs
10-30OVWE16E1Maintenance10

2.Remove the socket and bulb assembly
together by turning it anticlockwise, and then remove the bulb by pulling it out.
3. To install the bulb, perform the removal
steps in reverse.
Licence plate lamps
E01004602136
1. Remove the mounting screws and re-
move the lamp unit.
2. Remove the socket and bulb assembly
(A) together by turning it anticlockwise and then remove the bulb by pulling it out.
3. To install the bulb, perform the removal
steps in reverse.
NOTEl When installing the lamp unit, make sure the
direction of the lens is installed as shown in the illustration.
*: Right side of the vehicle
Room & map lamps
E01009500093
1. Insert a straight blade (or minus) screw-
driver with a cloth over its tip into the
lens and pry gently to remove it.
Replacement of lamp bulbs
10-31OVWE16E1Maintenance10 *