2016 KIA SEDONA light

13
Reverse Parking Aid Function*
When the gear shift lever is moved into R (Reverse)
and while the vehicle is moving backwards, the outside
rearview mirrors [A] will rotate downward to aid in
reverse parking .
When the left or right mirror buttons [B] are depressed,
the Reverse Parking Aid Function will operate .
To turn OFF the function, press the switches again.
The outside rearview mirrors will automatically return to
their original positions when:
•The ENGINE START/STOP Button is in the
OFF position
•The gear shift lever is moved to any position except
R (Reverse)
• Outside rearview mirror switches are not depressed
REMINDER: When the outside rearview mirror switches are not depressed, the Reverse Parking Aid Function will not operate and the outside rearview mirrors will not rotate downward .
(Button/switch panel located on Driver's Door )
AB
Engine Start/Stop Button & Smart Key Video
To view a video on your mobile device, snap this QR Code or visit the listed website .
Refer to page 2 for more information .
QR CODE
www.KuTechVideos.com/yp13/2016
Engine Start/Stop Button
To start the engine:
1 . Depress the brake pedal
2 . Press the ENGINE START/STOP button
while gear shift is in P (Park)

To turn the engine OFF: Press the ENGINE START/STOP button .
To use the ENGINE START/STOP button, you must have the
Smart Key fob on your person or inside the vehicle .
REMINDERS:
• In an emergency situation while the vehicle is in motion, you are able to turn the engine off and to the ACC position by pressing the ENGINE START/STOP button for more than 2 seconds or 3 times successively within 3 seconds
• If Smart Key fob battery is dead, with the lock button facing the ENGINE START/STOP button, hold the fob up against the ENGINE START/STOP button and press
To use electrical accessories:
ACC position •When in the OFF position and without depressing the brake pedal, press the ENGINE START/STOP button once (orange light)
ON position •When already in the ACC position (orange light) and without depressing the brake pedal, press the ENGINE START/STOP button again (red light) • When in the OFF position and without depressing the brake pedal, press the ENGINE START/STOP button twice (red light)
Keeping the vehicle in ACC or the ON position for extended periods of time without turning engine on may discharge the vehicle’s battery .
QUICK TIPS
A
B
B
ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. *IF EQUIPPED
DRIVER'S PANEL

14
Tilt/Telescoping Steering Wheel
To adjust the Steering Wheel, press the Lock-Release Lever [A] down and
adjust [B] the distance and [C] desired angle .
When finished, pull the Lock-Release Lever [A] up to lock Steering Wheel
in place .
A
B
C
Headlights & High Beams
To o p e r a t e :
•Rotate lever to change the Headlight function
•Push lever to turn High Beams ON
•Pull lever to flash Headlights/High Beams
AUTO Light function — When the light switch is in the AUTO Light
position, the tail lights and headlights will turn ON/OFF automatically
depending on the amount of light outside the vehicle .
Headlight position
Parking light position
AUTOAutomatic Headlights position
OFFOFF position
A
CB
A
SEDONA FEATURES & FUNCTIONS GUIDE
*IF EQUIPPED
STEERING WHEEL CONTROLS

15
Turn Signals & Fog Lights*
To o p e r a t e :
•Turn Signals - Move lever Up/Down for Right /Left Turn Signal
•Fog Lights - Push toggle switch to turn Fog Lights ON/OFF
REMINDER: Headlights must be ON for Fog Light operation .
One-Touch Lane Change Signal is activated by moving the Turn Signal
Lever slightly for less than 1 second and then releasing . The lane change
signal will blink 3 times .
To change how many times (3/5/7) the Lane Change Signal blinks, go to
User Settings Mode in the LCD Instrument Cluster modes .
For more information on the User Settings Mode, please refer to your Owner’s Manual.
Windshield Wipers & Washers
To o p e r a t e :
•Move lever Up/Down to change Wiper modes
•Press button [A] to adjust Intermittent Wipe
•Pull lever to spray and wipeM I S T: Single wipe
OFF: Wiper off
I N T: Intermittent Wipe
LO: Slow wipe
HI: Fast wipe
PUSH
FRONT
PULL
FRONT
PUSH
PULL
PUSH
FRONT
PULL
FRONT
PUSH
PULL
A
Rear Wiper & Washer*
To operate:
•Rotate Rear Wiper switch to change Wiper modes
•Push to spray and wipeHI: Fast wipe
LO: Slow wipe
OFF: Wiper off
A
Pressing button up increases Intermittent wipe frequency and wipe speed . Pressing button down decreases frequency of wipes .
QUICK TIP
LO and HI sets wiper speed . No intermittent wipe function on Rear Wipers .
QUICK TIP
ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. *IF EQUIPPED
STEERING WHEEL CONTROLS

38
How to Sync Transmitter with HomeLink®*
If programming for the first time, begin with Step 1 (repeating this step will
delete all information) .
To program non-rolling and rolling code garage door openers and
other devices:
1 . Press and hold the left [A] and center [D] buttons simultaneously until the
indicator light [C] begins to flash (to reprogram buttons, skip this step)
2 . Press and hold the desired button [A], [B] or [D] and hold the button
on the transmitter while it is approximately 1 to 3 inches away from
the mirror . The HomeLink® Indicator light [C] will flash rapidly once the
frequency signal has been successfully programmed
To finish programming rolling code garage door openers, complete
these steps:
3 . Locate the “learn” or “smart” button on the garage door’s motor
head unit . Press and release the button and complete Step 4 within
30 seconds
4 . Firmly press and release the programmed HomeLink® button up to
three times
Operating HomeLink®:
Press one of the programmed HomeLink® buttons .
Erasing programmed buttons:
Press and hold the left [A] and center [D] buttons simultaneously
for approximately 20 seconds, and then release both buttons within
30 seconds .
If your garage door opener was manufactured in 2011 or later, and you’re unable to program your vehicle’s HomeLink® system, you may need to purchase a HomeLink Repeater Kit. For more information, go to www.HomeLink.com or call (800) 355-3515.
The HomeLink® with Auto-Dimming Rearview Mirror* is designed to reduce
glare from a vehicle’s headlights located in the rear and also connect up to
three electronic transmitters into one location .
• To turn automatic dimming ON, press [~] button [F]
• To turn automatic dimming OFF, press [~] button [G]
REMINDER: Mirror indicator light [C] will illuminate when automatic dimming is ON .
HomeLink® with Auto-Dimming
Rearview Mirror*
[A] HomeLink® button
[B] HomeLink® button
[C] Indicator light
[D] HomeLink® button
[E] Glare detection sensor
[F] Automatic dimming ON
[G] Automatic dimming OFF
•
•You can reprogram a single HomeLink® button by repeating Step 2 •Erasing programmed buttons will delete all trained transmitters
QUICK TIPS
ABCDEFG
A
A
E
B
ABD
C
C
AD
F
F
CG
G
D
D
C
SEDONA FEATURES & FUNCTIONS GUIDE
*IF EQUIPPED
OTHER KEY FEATURES

39
Map/Room Lamps
Automatic turn off function*
The interior lights automatically turn off approximately 30 seconds after the
ENGINE START/STOP button is OFF .
Map/Room Lamp Operation
Press the lens [A] to turn the Map Lamp ON/OFF . This light produces a spot
beam for convenient use as a map lamp or as a personal lamp for the driver
or the front passenger .
When the button [B] is pressed the following occurs:
•When any door or the liftgate is opened, the map and room lamps turn ON
•When doors are unlocked from the Smart Key or key removed from
ignition, the Map and Room Lamps turn ON for approximately 30
seconds or until a door is opened
•When doors are closed, the lamps will gradually turn OFF after
approximately 30 seconds
•When all doors are locked or the ignition is turned ON, the Map Lamp
will turn OFF immediately .
When the button [C] is pressed, the lamps stay ON continuously .
Room Lamp - Press the lens [D] to turn the Room Lamp ON/OFF .
REMINDER: When Room Lamp lens is pressed ON it will remain ON, even when the Map Lamp switch is in the OFF position .

•When doors are unlocked by the Smart Key*, the lamp turns ON for approximately 30 seconds •If your vehicle is equipped with the theft alarm system, the interior lights automatically turn off approximately 3 seconds after the system is in armed stage •Using interior lights for an extended period of time may cause battery discharge
QUICK TIPS
A
CB
DD
A
Sunvisor
Use the Sunvisor to shield direct light through the front or side
windows . Slide the Sunvisor out and adjust as needed .
REMINDERS:
•Sunvisor may not shield all direct light
•The Sunvisor may impair visibility if not adjusted properly
• Be aware of seating position when adjusting or swinging Sunvisor around to or from the front or side windows .
A
B
D
C
(Lamp controls located in the overhead consoles)
ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. *IF EQUIPPED
OTHER KEY FEATURES

41
Back-Up Warning System
(Rear Parking Assist System)*
The Back-Up Warning System is not a safety device . The Back-Up Warning
System is a supplemental system that assists the driver by chiming if any
object is detected within the sensing area to the rear and side of the vehicle
when backing up .
The system is activated when the ignition is ON and the vehicle is in
R (Reverse) . To deactivate the system, press the Back-Up Warning System
button [A] (LED illuminated) .
REMINDERS:
•If the vehicle is moving at speeds over 3 mph, the system may not activate correctly
• When more than two objects are sensed at the same time, the closest one will be recognized first
The Back-Up Warning System is not a substitute for proper and safe backing-up procedures. Always drive safely and use caution when backing up. The Back-Up Warning System may not detect every object behind the vehicle.
(Navigation screen display shown)
Rear-Camera Display*
The Rear-Camera Display system is not a safety device . It is a supplemental
system that displays the view behind the vehicle through the Standard
Audio System, UVO eServices System and the UVO eServices with Premium
Navigation screens while the vehicle is in Reverse .
The Rear-Camera Display* activates when the:
•ENGINE START/STOP button is in the ON position (Green Light)
•Gear Shift Lever is in the R (Reverse) position
•To turn the Rear-Camera Display* OFF, press the camera button [B]
(Button located below Gear shift)
A
B
REMINDERS:
•The Rear-Camera Display* is ON by default when ignition is cycled
•While camera is active, only the volume controls on the Audio System can be operated
• The screen image above is for illustration purposes only . The actual image or graphics may differ in your vehicle
The Rear-Camera Display* is not a substitute for proper and safe backing-up procedures. The Rear-Camera Display may not display every object behind the vehicle. Always drive safely and use caution when backing up.
AB
ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. *IF EQUIPPED
OTHER KEY FEATURES

42
Power Liftgate (Tailgate)*
Inside the Vehicle:
Press the Power Liftgate Open/Close button* [A] to
automatically open/close the Liftgate .
Depress the POWER DOOR OFF button* [B] to disable .
REMINDER: If POWER DOOR OFF button is pressed, the Power Liftgate button on the Smart Key will be disabled .
REMINDERS:
•All doors are closed and locked after about 15 seconds
•If the POWER DOOR OFF button is depressed, the Smart Liftgate will not operate
• The Smart Power Liftgate feature will not operate when the doors are recently closed and locked, and the Smart Key is still detected after 15 seconds near the vehicle or within 60 inches of the door handles, a door is not locked or closed or the Smart Key is in the vehicle
For more information on the Smart Power Liftgate operation, please refer to the Owner's Manual.
Outside the Vehicle:
To open Power Liftgate* automatically, press the Rear Hatch
Release button [C] on exterior of the Liftgate .
Automatically close by pressing Power Liftgate Close button* [D] .
Smart Key:
To open the Power Liftgate*, press and
hold the Smart key Liftgate button [E]
until the Liftgate begins opening . Press
again to close .
REMINDER: Pulling the Rear Hatch upward by the handle or pressing the button a second time will interrupt the automatic opening of the Power Liftgate .

Smart Power Liftgate*
When the Smart Key fob is on your person and you are
near the back of the vehicle, within close proximity, the
hazard lights will blink and a chime will sound for about
3 seconds as an alert that the Smart Power Liftgate* is
about to open .
Then the alert system will blink and chime two additional
times before opening the Smart Power Liftgate* .
The Smart Power Liftgate* feature is OFF by default . To enable the Smart Power
Liftgate*, go to User Settings in the LCD Instrument Cluster modes .
During the Smart Power Liftgate alert, the Smart Power Liftgate can be deactivated with the Smart Key by pressing any button on the key fob .
QUICK TIPS
HOLDHOLD
HOLDE
D
C(Button located on inside edge of liftgate)
AB
(Buttons located on overhead console)
Smart Power Liftgate Video To view a video on your mobile device, snap this QR Code or visit the listed website .
Refer to page 2 for more information .
QR CODE
www.KuTechVideos.com/yp13/2016
AE
B
C
D
SEDONA FEATURES & FUNCTIONS GUIDE
*IF EQUIPPED
OTHER KEY FEATURES

43
Fuel Cap/Malfunction Indicator
(Check Engine Light)
Tighten for ONE CLICK to prevent Malfunction
Indicator [~] from illuminating .
REMINDER: The Fuel Filler Door Release button is located on the driver’s button panel, left of the Steering Wheel .
One-Click Fuel Cap Video To view a video on your mobile device, snap this QR Code or visit the listed website .
Refer to page 2 for more information .
QR CODE
www.KuTechVideos.com/yp13/2016
Child Safety Locks
Located on the front edge of the rear
passenger doors, press the Child Safety
Lock to the lock position [~] to disable
the inner door handles from opening the
rear passenger doors .
Hood Release Lever and Latch
Opening the Hood:
1 . Pull the Hood Release Lever [A] to unlatch the Hood
2 . In the front of the vehicle, lift the Hood slightly, push the secondary
Latch [B] to the left inside of the Hood’s center and lift the Hood
3 . Pull out the support rod from the Hood and set into place to hold
the Hood open
REMINDER: Open the Hood only after turning the engine off, on a flat surface, with the gear shift in P (Park) position and setting the parking brake .
(Lever located near floor below Driver's Panel) (Secondary latch located inside lip of Hood)
A
B
Closing the Hood:
Lower the Hood about halfway and then press down to securely lock
in place .
A
B
(Located on the front edge of the rear passenger doors)
ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. *IF EQUIPPED
OTHER KEY FEATURES