2016 KIA K900 light

DRIVER’S PA NEL
*IF EQUIPPED 12
REMINDERS:
- The system does NOT automatically park the vehicle
- This is a supplementary system. It is the
responsibility of the driver to always check the
area around the vehicle when parking the vehicle
Parking Guide System (PGS) \f Rear- Camera \bisplay*
§ Press TOP VIEW button to adjust the rear-view angle, as if looking down from above
§ Press the NORMAL VIEW button to adjust the rear-view angle, as a normal rear view perspective
www.KuTechVideos.com/kh13/2016
PARKING GUIDE
SYSTEM (PGS) VIDEO
To view a video on
your mobile device,
snap this QR Code or
visit the listed website.
Refer to page 2 for
more information.
The Parking Assist System is a supplemental system that
assists the driver by chiming if an object is detected within the
sensing areas in the front or rear of the vehicle when parking or
backing up.
When the ENGINE START/STOP button is ON and the shift
lever is in R (Reverse), the system is activated and the
Parking Assist button indicator is illuminated.
To turn off the Parking Assist System, press the button
A.
Parking Assist System
A
REMINDERS:
- If the vehicle is moving at speeds over 6 mph, the
system may not activate
- When more than two objects are sensed at the
same time, the closest one will be recognized rst
- The Parking Assist System is not a substitute for
proper and safe backing-up procedures. Always
drive safely and use caution when backing up.
The Parking Assist System may not detect every
object behind the vehicle
When parking (parallel parking or backing into or out of a
parking spot) the Parking Guide System (PGS)* displays the
vehicle’s projected trajectory on the navigation monitor. The
system also plays a series of audible tones as the vehicle
approaches an object, making parking e a sier.
The PGS will activate when the back-up light is ON with the
ENGINE START/STOP button ON and the shift lever in the
R (Reverse) position.
The rear-view angle of the camera can be changed by pressing
the following buttons on the navigation display:
(Buttons located on driver’s panel,
left of the steering wheel)
29319_Text.indd 1211/6/15 10:21 AM

DRIVER’S PA NEL
*IF EQUIPPED 14
To start the engine:
1. Depress the brake pedal
2. Press the ENGINE START/STOP button while gear shift is
in P (Park)
To turn the engine O F F, press the ENGINE START/STOP
button while the gear shift is in P (Park).
To use the ENGINE START/STOP button, you must have the
Smart Key on your person or inside the vehicle.
Engine Start/Stop Button
www.KuTechVideos.com/kh13/2016
ENGINE STA RT/STOP
BUTTON AND
SMART KEY VIDEO
To view a video on
your mobile device,
snap this QR Code or
visit the listed website.
Refer to page 2 for
more information.
REMINDERS:
-
If Smart Key fob battery is dead, you can still start the engine by pressing
the ENGINE START/STOP button with the Lock-button end of the Smart
Key. The Smart Key must contact the ENGINE START/STOP button directly,
at a right angle
- In an emergency situation while the vehicle is in motion, you are able to turn
the engine off and to the ACC position by pressing the ENGINE STA RT/ STOP
button for more than 2 seconds or 3 times successively within 3 seconds
B
CA
Quick Tip\f
To use electrical accessories:
ACC position
- When in the OFF position A and without
depressing the brake pedal, press the ENGINE
START/STOP
button once. The ACC indicator will illuminate (amber) B.
To check warning lights:
ON position
- When already in the ACC position
B and without
depressing the brake pedal, press the ENGINE
START/STOP button again. The ON indicator will
illuminate (red)
C.
- When in the OFF position
A and without
depressing the brake pedal, press the ENGINE
START/STOP button twice. The ON indicator will
illuminate (red)
C.
Keeping the vehicle in ACC or ON position too long
can discharge the vehicle’s battery.
29319_Text.indd 1411/6/15 10:21 AM

STEERING WHEEL CONTROLS
*IF EQUIPPED 16
Tu r n Signals & Fog Lights
To operate:
§ Move lever up/down for right /left turn signal
§ Slightly move lever up/down to activate one-touch lane
change signal
§ Press toggle switch
A up to turn fog lights ON/OFF
REMINDERS:
- Headlights must be ON for fog light operation
- One-touch lane change signal is activated by
moving the turn signal lever slightly for less than 1
second and then releasing. The lane change signal
will blink 3 times
- To change how many times the lane change signal
blinks (3/5/7), go to User Settings in the LCD
instrument cluster modes
For more information on the User Settings Mode,
please refer to your Owner’s Manual.
A
Hea\flights & High Beams
AUTO Light* – When the light switch is in the AUTO
Light position, the tail lights and headlights will turn
ON/OFF automatically depending on the amount of light
outside the vehicle.
AFLS (Adaptive Front Lighting System) – AFLS helps improve
visibility during nighttime driving by aiming the low-beam
headlights in the direction the vehicle is moving. AFLS controls
the aiming direction based on steering angle and speed.
When the light switch is in the AUTO light position, AFLS
will activate.
REMINDER: When the AFLS indicator illuminates on the instrument cluster, the
AFLS is not working properly. See authorized Kia dealer for service.§ Press lever away from you to turn
high beam headlights ON
§ Pull lever to ash headlights/
high beams
Headlight
/ High Beam Lever Operation
§ Rotate lever switch to change the
headlight function:
Headlight position
Parking light position
A\bTO *Auto Light* / AFLS position
DRL/OFFOFF or DRL OFF position
Daytime Running Lights (DRL) – DRL makes it easier for
others to see the front of your vehicle during the day. The lights
will be on automatically unless one of the following occurs:
§ Headlights are on
§ Parking brake is applied
§ Fog lights are on §
Switch is in the DRL
OFF position
§ Engine is turned off
29319_Text.indd 1611/6/15 10:22 AM

CENTER PA NEL
*IF EQUIPPED 22
Driver Information System (DIS) Contro\fs
B Home – Displays the audio control unit’s
Home menu which provides access to the
following options: Phone, U VO*, Settings,
Media, SiriusXM
®*, FM /A M, Navigation*, and
SiriusXM Data®*
C Phone – Displays the Phone menu which
provides access to the following options:
Keypad, Call His tor y, Contacts and Favorites
D Map/Voice – Displays a map of the current
location or repeats voice guidance
ABC
D
E
F
J
HG
K
L
L
I
E Nav – Displays the navigation screen which
provides access to the following menu options:
Route, Destination, Nearby POI Search, Add
to Address Book, Tr a f c, Guidance Volume
and Settings
F Menu – Provides access to additional
functions when available
G Back – Returns to the previous screen
Provides access to
all navigation and audio system control unit features.
A Controller – In addition to the touchscreen, the controller serves as a means for navigating K900’s UVO
Luxury Services with Premium Navigation system. The controller is actually three buttons: A scroll knob —
for scrolling the keyboard and menus and zooming in and out on the map screen; an 8-way joystick — for
toggling from left to right and top to bottom of menus and moving the focus of the navigation map; and a
push button — for selecting the highlighted feature
Scro\f\f Knob \b-Way Joystick Push Button
29319_Text.indd 2211/6/15 10:22 AM

CENTER PA NEL
27*IF EQUIPPED
A LWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPERATING INFORMATION AND SAFETY WARNINGS.
Automatic Climate Control System (continued\f
REMINDER: Your automatic climate control system
may differ from the image. See your Owner’s
Manual for more details.
Quick Ti\bs
- Keep inside glass as clean as possible to help
reduce window fogging
- Defrost Mode activates A /C and opens the fresh
air vent to help dehumidify the air and improve
defroster performance
Rear Climate Control
A Fan Speed Control knob
B Rear Climate Control OFF button
C Rear Climate Control LCD screen
D Rear Te m p e r a t u r e Control knob
E AUTO (Automatic) Climate Control button
F Climate Control REAR LOCK button
Tu r n the rear temperature control knob
D to set the rear
passenger’s zone temperature.
The rear seat, rear audio and rear climate controls can be
activated or deactivated by using the REAR LOCK button
F.
The REAR LOCK button light
F will be illuminated when the
rear seat controls are locked.
REAR LOCK settings can also be changed in the UVO
eServices with Premium Navigation system.
To set from the navigation system:
§ Press the CLIMATE button
§ Deselect the Rear Climate option
REAR LOCK settings return to the default setting when
ignition is cycled.
AB
CDE
F
www.KuTechVideos.com/kh13/2016
TRI-ZONE
AUTOMATIC CLIM ATE
CONTROL VIDEO
To view a video on
your mobile device,
snap this QR Code or
visit the listed website.
Refer to page 2 for
more information.
REMINDER: If the rear climate controls have been deactivated through
navigation system, they must be activated the same way.
29319_Text.indd 2711/6/15 10:22 AM

CENTER PA NEL
*IF EQUIPPED 28
Automatic Transmission (Shift by \fire) and S\bort Mode
To shift into any gear from Park, depress the brake pedal,
then press the Unlock button A, located on the side of the
gear shift lever, and shift.
P: Park – To shift into Park from any ge a r, press the P button
B on the gear shift while vehicle is stationary and the brake
pedal is depressed.
R: Reverse – To shift into Reverse, depress brake pedal,
press the Unlock button
A, and move the shift lever forward
twice to skip over Neutral and into Reverse.
N: Neutral
D: Drive
[+]: Sport Mode Upshift
[–]: Sport Mode Downshift
Sport Shift Mode: With the gear shift in Drive, pull the lever
to the left for Sport mode.
§ To upshift [+] – move the shift lever forward
§ To downshift [-] – pull the shift lever rearward
Paddle Shifters*: Paddle shifting is operable when the shift
lever is in the Sport mode position.
REMINDERS:
- Paddle shifters can be operated when the vehicle speed is more than 6 mph
- When in Sport mode, pulling the left and right paddle shifters at the same
time will NOT shift gears
www.KuTechVideos.com/kh13/2016
AUTOMATIC
TRANSMISSION
(SHIFT BY WIRE)
AND SPORT MODE
To view a video on
your mobile device,
snap this QR Code or
visit the listed website.
Refer to page 2 for
more information.
B
A
Quick Ti\bs
- Press the Unlock button
A when shifting from P
(Park) to any gear
- The instrument cluster and the light on top of
the shift lever identies the gear the vehicle is
currently in
REMINDERS:
- When in P (Park), if the Unlock button is not
pressed while shifting, the transmission does
not shift
- If the vehicle is turned off while in Neutral without
shifting into Park, it will remain in Neutral until
the driver’s door is opened. At that point it will
automatically shift into Park
- If going through a car wash, remind the attendant
to keep the vehicle in Neutral (N) and keep the
engine running. Also, disable the power trunk
lid control using the button inside the glove
compartment, turn off the auto rain-sensing
wipers and fold in the mirrors
(Button located on center panel below the gear shift)
CD
29319_Text.indd 2811/6/15 10:23 AM

CENTER PANEL
29*IF EQUIPPED
ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLE TE OPER ATING INFORMATION AND SAFE T Y WARNINGS.
The Electric Parking Brake (EPB) system utilizes an electric
motor to engage the parking brake.
Applying the Parking Brake
Depress the brake pedal and pull up the EPB switch
C.
Ensure that the indicator light
is illuminated on the
instrument cluster.
Releasing the Parking Brake
The EPB will automatically release when the shifter is placed
in Reverse or Drive. To release EPB manually, depress the
brake pedal, then press the EPB switch
C, with the ignition
switch in the ON position. Ensure that the indicator light

i s O F F.
Ele\ftri\f Parking Brake (EPB)
Aut\b H\bld
Qui\fk Tip
Pull up and hold EPB switch again to increase brake
pressure if parked on a decline or incline.
www.KuTechVideos.com/kh13/2016
ELECTRIC PARKING
BRAKE (EPB) / AUTO
HOLD VIDEO
To view a video on
your mobile device,
snap this QR Code or
visit the listed website.
Refer to page 2 for
more information.
REMINDERS: - As a bulb check, the EPB malfunction indicator will illuminate for approximately 3 seconds when the ignition switch is turned ON
- If the warning light does not illuminate temporarily or remains continuously lit, take your vehicle to an authorized Kia dealer and have the system checked
- The EPB should not be operated while the vehicle is moving
- A click or electric brake motor sound may be heard while operating or releasing the EPB. These conditions are normal and indicate that the EPB is functioning properly
Auto Hold temporarily maintains the vehicle at a standstill even if the brake pedal is released. Auto
Hold can be turned On/Off using the AUTO HOLD switch D on the center panel. Before Auto Hold
will operate, the driver’s door, engine hood and trunk must be closed and the driver’s seat belt must
be fastened.
The Auto Hold indicator, which is in the instrument cluster, has four states:
White : Standby – With vehicle at a standstill, and AUTO HOLD switch
D turned ON, the indicator
will illuminate white. While driving the vehicle (vehicle is not at a standstill), the Auto Hold indicator
will remain white.
Green : Engaged – When coming to a complete stop by depressing the brake pedal, the Auto Hold
indicator changes from white to green.
OFF (not illuminated) – The indicator will turn OFF when the AUTO HOLD switch
D is manually
turned OFF or when the EPB is manually turned ON.
Yellow : Malfunction – When the indicator is illuminated yellow, there may be a system malfunction.
Take your vehicle to a local Kia dealer.
29319_Text.indd 2911/6/15 10:23 AM

CENTER PA NEL
*IF EQUIPPED 30
Drive Mode Integrated Control Syste\f
NORMAL, ECO, SPORT, SMART and SNOW drive modes
may be changed according the driver’s preference or road
conditions. The system’s default mode is NORMAL and is not
displayed on the instrument cluster nor the navigation screen.
To change the drive mode from the NORMAL (default) mode,
press the DRIVE MODE button
A.
ECO Mode – A green ECO indicator will illuminate on the
instrument clu s t er. To deactivate, press the DRIVE MODE
button
A again to change the selection to another setting.
SPORT Mode – A yellow SPORT indicator will illuminate on
the instrument clu s t er. To deactivate, press the DRIVE MODE
button
A again to change the selection to another setting.
SNOW Mode – To activate, press the SNOW MODE button
B
located below the gear shift. It will operate regardless of the
mode you selected with the Drive Mode button. To deactivate
SNOW mode, press SNOW mode button
B again.
S\fart Mode
When SMART mode is activated, the system automatically
selects the drive mode (ECO, NORMAL, SPORT) best suited
to the current driving style (economic, average, aggressive). A
SMART indicator will illuminate on the instrument clu s t er. The
color of the SMART indicator (green, white, red) depends on
the current driving style. To deactivate, press the DRIVE MODE
button
A again to change the selection to another setting.
Quic\b Tip

When the ENGINE START/STOP button is turned
of f, the system will default to Normal mode and
each mode will need to be selected again when the
vehicle restarts.
REMINDERS:

When ECO mode is selected, the following may
occur to improve fuel economy:
- Acceleration may be slightly reduced even when
the accelerator is fully depressed
- Air conditioner performance may be limited
- Shift pattern of the automatic transmission
may change
- Engine noise may increase
- System’s power will be limited when
driving uphill
- When SPORT mode is selected, fuel economy
may decrease
- When SNOW MODE is selected, the SNOW mode
will operate regardless of which drive mode
(NORMAL/SPORT/ECO/SMART) is selected
B
(Button located on center panel below the gear shift)
A
29319_Text.indd 3011/6/15 10:23 AM