2016 JEEP WRANGLER lock

TILT STEERING COLUMN
This feature allows you to tilt the steering column
upward or downward. The tilt lever is located on the
steering column, below the turn signal lever.Push down on the lever to unlock the steering column.
With one hand firmly on the steering wheel, move the
steering column up or down, as desired. Pull upwards on
the lever to lock the column firmly in place.
Mist Control
Tilt Steering Column Lever
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!
Do not adjust the steering column while driving.
Adjusting the steering column while driving or driv-
ing with the steering column unlocked, could cause the
driver to lose control of the vehicle. Failure to follow
this warning may result in serious injury or death.
ELECTRONIC SPEED CONTROL — IF EQUIPPED
When engaged, the Electronic Speed Control takes over
accelerator operations at speeds greater than 25 mph
(40 km/h).
The Electronic Speed Control buttons are located on the
right side of the steering wheel.
Electronic Speed Control Buttons
1 — ON/OFF3 — SET -
2 — RES + 4 — CANCEL
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181

STORAGE
Glove Compartment
The lockable glove compartment is located on the pas-
senger side of the lower instrument panel. Pull outward
on the handle/latch to open the glove compartment.
Console Storage Compartment
To lock or unlock the storage compartment, insert the
ignition key and turn. To open the storage compartment,
push the latch and lift the cover.
Center Console
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

9. Reinstall the hard top. Refer to “Freedom Top Three-Piece Modular Hard Top — Front/Rear Panel Instal-
lation” in this section.
Installing The Soft Top — Four-Door Models
NOTE: The following procedures are for first time set up
only. For future soft top procedures, refer to “Soft Top” in
this section.
1. Locate and remove the following items prior to hard top removal:
• Right and left door frames
• Six door frame attachment knobs
• Right and left quarter windows
• Rear window 2. Remove the hard top. Refer to “Freedom Top Three-
Piece Modular Hard Top — Front/Rear Panel Re-
moval” in this section.
3. Install the door frames. Refer to “Door Frame” in this section.
4. Install the soft top with the pivot brackets above the sport bar brackets, lower the soft top into the sport bar
bracket slots in a downward motion to lock tab on soft
top. You will need to lift the top to get the brackets to
line up. (Another person may be needed to help with
this operation.)
202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

NOTE:If you are doing this alone, use one arm to hold
the soft top up, the other to align the brackets.
5. Lower the pivot bracket onto the sport bar bracket mounting tab in a downward motion to lock into tab. 6. Install the pivot bracket bolts back into place using a
10.0 mm wrench or socket driver. Secure them until
they are snug, being careful not to cross-thread the
screws or overtighten.
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203

Front Panel(s) Removal
NOTE: Left panel must be removed before removing
right panel.
1. Fold down the sun visor, and move it to the side.
2. Turn the rear fasteners (knobs) (located on the over-head speaker bar assembly) counterclockwise until
they can be removed.
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207

3. Turn the center L-shaped locks (two) from the centerof the roof panel. 4. Turn the rear L-shaped lock (located above the shoul-
der belt anchorage).
208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Front Panel(s) Installation With Rear Hard Top
Removed
1. Turn the left and right panels over and move thespacer block (located on the rear of the panel) upward
90 degrees. NOTE:
The front panel(s) must be positioned properly
to ensure sealing. Set the panels on the windshield frame
so that there is no overhang. Also, make sure that the
panels are sitting flush with the body.
2. Install the right panel first, then the left panel.
3. Reinstall the panel(s) using the same steps for removal in reverse order.
Rear Hard Top Removal
1. Remove both front panels. Refer to “Front Panel(s)Removal” in this section.
2. Open both doors.
3. Remove the two Torx head screws that secure the hard top at the B-pillar (near the top of the door) using a #40
Torx head driver (Four–Door Only).
214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE