2016 Hyundai Creta belt

7-28
Maintenance
EXPlANATION OF SChEdulEd MAINTENANCE ITEMS
Engine oil and filter
The engine oil and filter should be
changed at the intervals specified in
the maintenance schedule. If the car
is being driven in severe conditions,
more frequent oil and filter changes
are required.
Drive belts
Inspect all drive belts for evidence of
cuts, cracks, excessive wear or oil
saturation and replace if necessary.
Drive belts should be checked peri
odically for proper tension and
adjusted as necessary.
When you are inspecting the belt,
place the ignition switch in the
LOCK/OFF or ACC position.
Fuel filter
A clogged filter can limit the speed at
which the vehicle may be driven,
damage the emission system and
cause multiple issues such as hard
starting. If an excessive amount of
foreign matter accumulates in the
fuel tank, the filter may require
replacement more frequently.
After installing a new filter, run the
engine for several minutes, and
check for leaks at the connections.
We recommend that the fuel filter be
replaced by an authoized HYUNDAI
dealer.
Fuel lines, fuel hoses and con
nections
Check the fuel lines, fuel hoses and
connections for leakage and dam
age. We recommend that the fuel
lines, fuel hoses and connections be
replaced by an authoized HYUNDAI
dealer.
NOTICE
Diesel Engine
Never work on injection system
with engine running or within 30
seconds after shutting off engine.
High pressure pump, rail, injectors
and high pressure pipes are sub
ject to high pressure even after
the engine stopped. The fuel jet
produced by fuel leaks may cause
serious injury, if it touch the body.
People using pacemakers should
not move than 30cm closer to the
ECU or wiring harness within the
engine room while engine is run
ning, since the high currents in the
Common Rail system produce
considerable magnetic fields.
WARNING

7-59
7
Maintenance
4. Tire ply composition and materi
al
The number of layers or plies of rub
bercoated fabric in the tire. Tire
manufacturers also must indicate the
materials in the tire, which include
steel, nylon, polyester, and others.
The letter "R" means radial ply con
struction; the letter "D" means diago
nal or bias ply construction; and the
letter "B" means beltedbias ply con
struction.
5. Maximum permissible inflation
pressure
This number is the greatest amount
of air pressure that should be put in
the tire. Do not exceed the maximum
permissible inflation pressure. Refer
to the Tire and Loading Information
label for recommended inflation
pressure.
6. Maximum load rating
This number indicates the maximum
load in kilograms and pounds that
can be carried by the tire. When
replacing the tires on the vehicle,
always use a tire that has the same
load rating as the factory installed
tire.
7. Uniform tire quality grading
Quality grades can be found where
applicable on the tire sidewall
between tread shoulder and maxi
mum chapter width.
For example:
TREAD wear 200
TRACTION AA
TEMPERATURE A
Tire age
Tires degrade over time, even
when they are not being used.
Regardless of the remaining
tread, it is recommended that tires
generally be replaced after six (6)
years of normal service. Heat
caused by hot climates or frequent
high loading conditions can accel
erate the aging process. Failure
to follow this warning could cause
sudden tire failure, which could
lead to a loss of control and an
accident involving serious injury or
death.
WARNING

7-95
7
Maintenance
Cleaning the upholstery and interi
or trim
Vinyl
Remove dust and loose dirt from
vinyl with a whisk broom or vacuum
cleaner. Clean vinyl surfaces with a
vinyl cleaner.
Fabric
Remove dust and loose dirt from fab
ric with a whisk broom or vacuum
cleaner. Clean with a mild soap solu
tion recommended for upholstery or
carpets. Remove fresh spots imme
diately with a fabric spot cleaner. If
fresh spots do not receive immediate
attention, the fabric can be stained
and its color can be affected. Also, its
fireresistant proper ties can be
reduced if the material is not proper
ly maintained.
Using anything but recommended
cleaners and procedures may affect
the fabric’s appearance and fire
resistant properties.
Cleaning the lap/shoulder belt
webbing
Clean the belt webbing with any mild
soap solution recommended for
cleaning upholstery or carpet. Follow
the instructions provided with the
soap. Do not bleach or redye the
webbing because this may weaken it.
Cleaning the interior window glass
If the interior glass surfaces of the
vehicle become fogged (that is, cov
ered with an oily, greasy or waxy
film), they should be cleaned with
glass cleaner. Follow the directions
on the glass cleaner container.
Do not scrape or scratch the inside
of the rear window. This may result
in damage to the rear window
defroster grid.
NOTICE
NOTICE