2016 Hyundai Creta headlight bulb

F18F18
Fuel filter (For Diesel) ........................................7-40Draining water from fuel filter ....................................7-40
Extracting air from the fuel filter ..............................7-40
Air cleaner ............................................................7-41 Filter replacement ........................................................7-41
Climate control air filter .....................................7-42 Filter inspection ...............................................................7-42
Filter replacement ...........................................................7-42
Wiper blades .........................................................7-44 Blade inspection ..............................................................7-44
Blade replacement ..........................................................7-44
Battery...................................................................7-47 For best battery service................................................7-47
Battery capacity label ....................................................7-49
Battery recharging .........................................................7-49
Reset items .......................................................................7-50
Tires and wheels ..................................................7-51 Tire care ............................................................................7-51
Recommended cold tire inflation pressures.............7-51
Checking tire inflation pressure ..................................7-53
Tire rotation .....................................................................7-54
Wheel alignment and tire balance ..............................7-55
Tire replacement .............................................................7-55
Wheel replacement ........................................................7-56
Tire traction ......................................................................7-57 Tire maintenance ...........................................................7-57
Tire sidewall labeling ......................................................7-57
Low aspect ratio tire ......................................................7-61
Fuses ......................................................................7-63 Instrument panel fuse replacement ...........................7-64
Engine compartment panel fuse replacement.........7-66
Fuse/Relay panel description ......................................7-68
Light bulbs.............................................................7-78 Headlight, position light, turn signal light,
and front fog light bulb replacement ........................7-79
Side repeater light bulb replacement.........................7-84
Rear combination light bulb replacement .................7-84
High mounted stop light ................................................7-86
License plate light bulb replacement ........................7-87
Interior light bulb replacement ....................................7-88
Appearance care ..................................................7-89 Exterior care ....................................................................7-89
Interior care......................................................................7-94
Emission control system .....................................7-96 Crankcase emission control system ...........................7-96
Evaporative emission control system.........................7-96
Exhaust emission control system ...............................7-97

7
Fuses ......................................................................7-63Instrument panel fuse replacement ...........................7-64
Engine compartment panel fuse replacement.........7-66
Fuse/Relay panel description ......................................7-68
Light­bulbs.............................................................7-78 Headlight, position light, turn signal light, and front fog light bulb replacement ....................7-79
Side repeater light bulb replacement.........................7-84
Rear combination light bulb replacement .................7-84
High mounted stop light ................................................7-86
License plate light bulb replacement ........................7-87
Interior light bulb replacement ....................................7-88
Appearance­care ..................................................7-89 Exterior care ....................................................................7-89
Interior care......................................................................7-94
Emission­control­system .....................................7-96 Crankcase emission control system ...........................7-96
Evaporative emission control system.........................7-96
Exhaust emission control system ...............................7-97

7-78
Maintenance
lIGhT BulBS
Consult an authorized HYUNDAI
dealer to replace most vehicle light
bulbs. It is difficult to replace vehicle
light bulbs because other parts of the
vehicle must be removed before you
can get to the bulb. This is especially
true for removing the headlight
assembly to get to the bulb(s).
Removing/installing the headlight
assembly can result in damage to
the vehicle.Information
After heavy driving, rain or washing
headlight and taillight lenses could
appear frosty. This condition is caused
by the temperature difference between
the lamp inside and outside.
This is similar to the condensation on
your windows inside your vehicle dur
ing the rain and doesn’t indicate a
problem with your vehicle. If the
water leaks into the lamp bulb circuit
ry, we recommend that the system be
checked by an authorized HYUNDAI
dealer.
Be sure to replace the burnedout
bulb with one of the same wattage
rating. Otherwise, it may cause dam
age to the fuse or electric wiring sys
tem.
NOTICE
i
Prior to replacing a light, depress
the foot brake, move the shift lever
into the P (Park, for automatic
transaxle vehicle) or neutral (for
manual transaxle vehicle), apply
the parking brake, place the igni
tion switch in the LOCK/OFF posi
tion, and take the key with you
when leaving the vehicle to avoid
sudden movement of the vehicle
and to prevent possible electric
shock.
Be aware the bulbs may be hot
and may burn your fingers.
WARNING

7-79
7
Maintenance
Headlight, position light, turn sig
nal light, static bending light and
front fog light bulb replacement
Type A
(1) Headlight (Low/High)
(2) Parking (Position) light
(3) Front turn signal light
(4) Front fog light (if equipped)
(5) Daytime running light (if equipped)
Information
If the headlight aiming adjustment is
necessary after the headlight assembly
is reinstalled, consult an authorized
HYUNDAI dealer.i
OGS075054
•Always handle them carefully,
and avoid scratches and abra
sions. If the bulbs are lit, avoid
contact with liquids. Never touch
the glass with bare hands.
Residual oil may cause the bulb
to overheat and burst when lit. A
bulb should be operated only
when installed in a headlight.
•If a bulb becomes damaged or
cracked, replace it immediately
and carefully dispose of it.
•Wear eye protection when
changing a bulb. Allow the bulb
to cool down before handling it.Halogen bulbs
•Halogen bulbs contain pressur
ized gas that will produce flying
pieces of glass if broken.
(Continued)
(Continued)
WARNING
OLMB073042L

7-80
Maintenance
Headlight (Low/High)
1. Open the hood.
2. Remove the headlight bulb cover by turning it counterclockwise.
3. Disconnect the headlight bulb socketconnector.
4. Unsnap the headlight bulb retain ing wire by depressing the end
and pushing it upward.
5. Remove the bulb from the head light assembly. 6. Install a new headlight bulb and
snap the headlight bulb retaining
wire into position by aligning the
wire with the groove on the bulb.
7. Connect the headlight bulb socket connector.
8. Install the headlight bulb cover by turning it clockwise.
Turn signal light
1. Remove the turn signal light bulbcover by turning it counterclock
wise.
2. Remove the socket from the assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
3. Insert a new bulb by inserting it into the socket and rotating it until
it locks into place.
4. Install the socket in the assembly by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
5. Install the turn signal light bulb cover by turning it clockwise.
OGS075050
Turn signal lightParking
(Position) light
Headlight

7-81
7
Maintenance
Parking (Position) light
1. Remove the socket from the
assembly by pulling it straight out.
2. Remove the bulb from the socket by pulling it out.
3. Insert a new bulb by inserting it into the socket.
4. Install the socket in the assembly by pushing it in.
Front fog light bulb replacement
1. Remove the under cover by rotating the screws and bolts.
2. Reach your hand into the back of the front bumper.
3. Disconnect the power connector from the socket.
4. Remove the bulbsocket from the housing by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the housing.
5. Install the new bulbsocket into the housing by aligning the tabs on
the socket with the slots in the
housing. Push the socket into the
housing and turn the socket clock
wise.
6. Connect the power connector to the socket.
7. Reinstall the front bumper under cover.
Type B
(1) Headlight (Low/High)
(2) Parking (Position) light
(3) Front turn signal light
(4) Static bending light
(5) Front fog light (if equipped)
(6) Daytime running light (if equipped)
OGS075055

7-82
Maintenance
Information
If the headlight aiming adjustment is
necessary after the headlight assembly
is reinstalled, consult an authorized
HYUNDAI dealer.
Headlight (Low/High) and static
bending light replacement
1. Open the hood.
2. Remove the headlight bulb cover by turning it counterclockwise.
3. Disconnect the headlight bulb socketconnector.
4. Unsnap the headlight bulb retain ing wire by depressing the end
and pushing it upward.
5. Remove the bulb from the head light assembly.
i
•Always handle them carefully,
and avoid scratches and abra
sions. If the bulbs are lit, avoid
contact with liquids. Never touch
the glass with bare hands.
Residual oil may cause the bulb
to overheat and burst when lit. A
bulb should be operated only
when installed in a headlight.
•If a bulb becomes damaged or
cracked, replace it immediately
and carefully dispose of it.
•Wear eye protection when
changing a bulb. Allow the bulb
to cool down before handling it.Halogen bulbs
•Halogen bulbs contain pressur
ized gas that will produce flying
pieces of glass if broken.
(Continued)
(Continued)
WARNING
OLMB073042L
OGS075051
Static bending light
Turn signal
Low/High

7-83
7
Maintenance
6. Install a new headlight bulb and
snap the headlight bulb retaining
wire into position by aligning the
wire with the groove on the bulb.
7. Connect the headlight bulb socket connector.
8. Install the headlight bulb cover by turning it clockwise.
Information
BiFunction projection
headlamp
This headlamp is bifunction type that
switches the low beam to high or the
high beam to low using solenoid sys
tem. So, the moving sound may be
heard when the headlamp switches
the low beam to high or the high beam
to low and it does not indicate mal
function of the headlamp.
Turn signal light
1. Remove the turn signal light bulb cover by turning it counterclock
wise.
2. Remove the socket from the assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
3. Insert a new bulb by inserting it into the socket and rotating it until
it locks into place.
4. Install the socket in the assembly by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
5. Install the turn signal light bulb cover by turning it clockwise.
Front fog light bulb replacement
1.Remove the under cover by rotating the screws and bolts.
2.Reach your hand into the back of the front bumper.
3.Disconnect the power connector from the socket.
4.Remove the bulbsocket from the housing by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the housing.
5.Install the new bulbsocket into the housing by aligning the tabs on the
socket with the slots in the hous
ing. Push the socket into the hous
ing and turn the socket clockwise.
6.Connect the power connector to the socket.
7.Reinstall the front bumper under cover.
i